Henny Penny 680 KFC manual

Page 43

Before replacing a high temperature limit control, check to see that its circuit is closed.

The shortening temperature must be below 380°F (193°C) to accurately perform this check.

1. Remove electrical power supplied to the fryer.

Remove electrical power supplied to the fryer by unplugging the unit, or by turning off the wall circuit breaker or electrical shock could result.

2.Remove the control panel.

3.Remove the two electrical wires from the high temperature limit control.

4.Manually reset the control, then check for continuity between the two terminals after resetting the control. If the circuit is open, replace the control, then continue with this procedure. (If the circuit is closed, the high limit is not defective. Reconnect the two electrical wires.)

Remove electrical power supplied to the fryer by unplugging the unit, or by turning off the wall circuit breaker or electrical shock could result.

1.If the tube is broken or cracked, the control will open, shut- ting off electrical power. The control cannot be reset.

2.Drain shortening from the eookpot and discard. A substance in the tube could contaminate the shortening.

3.Remove control panel.

4.Loosen small inside screw nut on capillary tube.

Image 43

Contents Page Henny Penny 8 Head GAS Pressure Fryer SpecificationsPage Page Limited Warranty for Henny Penny Appliances Introduction Section Heat IntroductionPressure Fryer PressurePage Page Page Prop UP a Ramp for Each Caster on the Selected Side Insert Page Page Page ALL STR N Unit again after installation Shortening MAY Start UP Procedure Lever Is not to be Pulled Page Page Push handle back and raise lid Melt Cycle Operation Switches IndicatorsLo Mode Cool ModeHeat Light will illuminate whenever the control calls for Page Refer to KFC’s Standards Library on cleaning instructions Page 397 Connecw Hj i’.,‘i ,e.*f Page Product Color Not Correct Too Dark Spotted Rancid Taste Shortening Too old Pressure will not Eplace pressure plate Replace module Heating of shortening too slow Or boil Water Shortening Ing over Gasket coming out of lid Pressure System Page Page Pump Position Check from Page Every 90 days Complete ControlPanel Henny Penny Pressure RegulationPage Page Page Pressure PAD LID Counterweight CONT’DLID Adjustment Hertz Page Operating Control Valve ReplacementSolenoid Valve SeatOperating Control Do not Manuallyactivate the SafetyRemoval & Cleaning Safety ValvePressure Gauge Do not Disassemble or Modify this VavleCalibration Steps Page Page Page Page Page Page Page Page Page Using 3/8 socket, remove nut securing ground wire If no red glow is seen, proceed with the following Page Page Page Epyg-ui nuebq plea ewy Page Page Page Page Product One Part PER Number Description Assy UnitsLatch Plate PANEL, Right Side Page Not Avail Page Carriage Counterweight BARPart PER Number Description CableHenny Penny Model 1005 CAM Slide Filler LinkageassemblyUnits Part PER Number Description Assy LID Instruction LabelPage 705 Page Pipe ELBOW, 1/4 Dead WeightFitting Connector Pressure GaugePage HI-LIMIT LINK, Drain RODSUPPORT, Drain ROD BRACKET, HI-LIMITPage Units Smooth and Rounded Edge of Blade HOUSING, Coil Solenoid ValveassemblyCORE, Disc Assembly COVER, Coil HousingHead GAS Cooker I I SIE IAy--4A-+-7 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 IfApplicable SMS ProgrammingCode After the load compensation, press and release the Func Review Usage SMS Special ProgramMode Speaker Frequency, Codes, Initialize System Reset UsageFactory Presets F/C, Gas/Electric, Speaker Volume ModeAppliance Test Tech I/O ModeHeat Control Press and release the Function button and MELT, Mode