Henny Penny 680 KFC manual Using 3/8 socket, remove nut securing ground wire

Page 67

6.Remove air hose.

7.Remove pilot orifice and elbows off of faulty burner.

8.Screw pilot orifice and elbows onto new burner.

Use pipe thread sealant on threads on elements.

9. Remove old insulation from burner area.

10. .Using a gasket adhesive, mount the insulation provided onto the outer surface of burner bracket.

Do not get adhesive onto burner “windows”. It will discolor, blocking the view.

11.Carefully mount burner assembly onto studs and bracket, making sure the insulation seals around burner.

Avoid striking the ignitor while making the installa- tion. Also, do not over-tighten the nuts on the studs, or the studs could break.

12.Fasten condensation deflector onto frame and reconnect gas line into fitting on new burner.

13.Check for gas leaks per section in the installation portion of this manual.

14.Place side panel on unit, turn gas on and electrical supply to unit.

ace

t: Right Burner

1.

Follow steps 1 thru

3 on left burner instructions, except

 

 

 

remove right side panel, and drop down drain rod.

 

 

2.

Using 3/8” socket, remove nut securing ground wire and

 

 

 

nuts securing the burner assembly. Drop burner assembly

 

 

 

from unit.

 

 

 

3.

Follow steps 6 thru

15 on the left burner instructions.

Image 67
Contents Page Henny Penny 8 Head GAS Pressure Fryer SpecificationsPage Page Limited Warranty for Henny Penny Appliances Introduction Section Heat IntroductionPressure Fryer PressurePage Page Page Prop UP a Ramp for Each Caster on the Selected Side Insert Page Page Page ALL STR N Unit again after installation Shortening MAY Start UP Procedure Lever Is not to be Pulled Page Page Push handle back and raise lid Melt Cycle Operation Switches IndicatorsLo Mode Cool ModeHeat Light will illuminate whenever the control calls for Page Refer to KFC’s Standards Library on cleaning instructions Page 397 Connecw Hj i’.,‘i ,e.*f Page Product Color Not Correct Too Dark Spotted Rancid Taste Shortening Too old Pressure will not Eplace pressure plate Replace module Heating of shortening too slow Or boil Water Shortening Ing over Gasket coming out of lid Pressure System Page Page Pump Position Check from Page Every 90 days Complete ControlPanel Henny Penny Pressure RegulationPage Page Page Pressure PAD LID Counterweight CONT’DLID Adjustment Hertz Page Operating Control Valve ReplacementSolenoid Valve SeatOperating Control Do not Manuallyactivate the SafetyRemoval & Cleaning Safety ValvePressure Gauge Do not Disassemble or Modify this VavleCalibration Steps Page Page Page Page Page Page Page Page Page Using 3/8 socket, remove nut securing ground wire If no red glow is seen, proceed with the following Page Page Page Epyg-ui nuebq plea ewy Page Page Page Page Product One Part PER Number Description Assy UnitsLatch Plate PANEL, Right Side Page Not Avail Page Carriage Counterweight BARPart PER Number Description CableHenny Penny Model 1005 CAM Slide Filler LinkageassemblyUnits Part PER Number Description Assy LID Instruction LabelPage 705 Page Pipe ELBOW, 1/4 Dead WeightFitting Connector Pressure GaugePage HI-LIMIT LINK, Drain RODSUPPORT, Drain ROD BRACKET, HI-LIMITPage Units Smooth and Rounded Edge of Blade HOUSING, Coil Solenoid ValveassemblyCORE, Disc Assembly COVER, Coil HousingHead GAS Cooker I I SIE IAy--4A-+-7 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 IfApplicable SMS ProgrammingCode After the load compensation, press and release the Func Review Usage SMS Special ProgramMode Speaker Frequency, Codes, Initialize System Reset UsageFactory Presets F/C, Gas/Electric, Speaker Volume ModeAppliance Test Tech I/O ModeHeat Control Press and release the Function button and MELT, Mode