Henny Penny 680 KFC manual Or boil Water Shortening Ing over

Page 40

Foaming	or boil-	Water in	shortening.
ing over	of
shortening.
		Condensation line		stopped
		up.
		Improper	or bad
		shortening.
		Improper	filtering.
		Cold zone full of cracklings.
		Improper	rinsing	after
		cleaning	the fryer.

At end of cooking cycle, drain shortening and clean cookpot. Add fresh shortening.

Remove and clean conden- sation line.

Use recommended shortening.

Refer to the procedure covering filtering the shortening.

Filter shortening.

Clean and neutralize the cookpot. Rinse with vinegar to remove the alkaline, then rinse with hot water and dry cookpot.

Shortening		will	Drain	valve	clogged	with	Open valve - push cleaning
not drain	from		crumbs.				brush through drain open-
cookpot							ing from inside of cookpot.
			Drain	valve	will not	open by	Replace cotter	pins in valve
			pulling	the knob.			coupling.
Shortening		leaking	Obstruction		in drain.
through	drain		Faulty	drain	valve.		Replace drain	valve.
valve.			Faulty	drain	valve.		Replace drain	valve.

Image 40

Contents Page Specifications Henny Penny 8 Head GAS Pressure FryerPage Page Limited Warranty for Henny Penny Appliances Introduction Section Introduction Pressure FryerPressure HeatPage Page Page Prop UP a Ramp for Each Caster on the Selected Side Insert Page Page Page ALL STR N Unit again after installation Shortening MAY Start UP Procedure Lever Is not to be Pulled Page Page Push handle back and raise lid Switches Indicators Lo ModeCool Mode Melt Cycle OperationHeat Light will illuminate whenever the control calls for Page Refer to KFC’s Standards Library on cleaning instructions Page 397 Connecw Hj i’.,‘i ,e.*f Page Product Color Not Correct Too Dark Spotted Rancid Taste Shortening Too old Pressure will not Eplace pressure plate Replace module Heating of shortening too slow Or boil Water Shortening Ing over Gasket coming out of lid Pressure System Page Page Pump Position Check from Page Complete Control Panel Henny PennyPressure Regulation Every 90 daysPage Page Page LID Counterweight CONT’D Pressure PADLID Adjustment Hertz Page Replacement Solenoid ValveSeat Operating Control ValveDo not Manuallyactivate the Safety Removal & CleaningSafety Valve Operating ControlPressure Gauge Do not Disassemble or Modify this VavleCalibration Steps Page Page Page Page Page Page Page Page Page Using 3/8 socket, remove nut securing ground wire If no red glow is seen, proceed with the following Page Page Page Epyg-ui nuebq plea ewy Page Page Page Page Product One Units Part PER Number Description AssyLatch Plate PANEL, Right Side Page Not Avail Page Counterweight BAR Part PER Number DescriptionCable CarriageHenny Penny Model 1005 Linkageassembly Units Part PER Number Description AssyLID Instruction Label CAM Slide FillerPage 705 Page Dead Weight Fitting ConnectorPressure Gauge Pipe ELBOW, 1/4Page LINK, Drain ROD SUPPORT, Drain RODBRACKET, HI-LIMIT HI-LIMITPage Units Smooth and Rounded Edge of Blade Solenoid Valveassembly CORE, Disc AssemblyCOVER, Coil Housing HOUSING, CoilHead GAS Cooker I I SIE IAy--4A-+-7 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 IfApplicable SMS ProgrammingCode After the load compensation, press and release the Func Review Usage SMS Special ProgramMode Reset Usage Factory Presets F/C, Gas/Electric, Speaker VolumeMode Speaker Frequency, Codes, Initialize SystemAppliance Test Tech I/O ModeHeat Control Press and release the Function button and MELT, Mode