Henny Penny 680 KFC manual

Page 66

: Left ‘Burner

I

I

urners are different colors.

1.Remove electrical power supplied to the unit.

Remove electrical power supplied to the unit by unplug- ging the unit, or by turning off the wall circuit breaker, or electrical shock could result.

2.Using l/4” socket, remove both side panels.

3.Locate the air adjustment behind the control panel on each side of the unit.

4.Loosen the nuts securing the slide adjustments.

5.Replace power to unit and turn Power Switch to the “Power” position.

6.While the burners are igniting continously, slide the adjustment shield open or close until both burners are orangy-red. (Refer to color chart.)

7.Tighten nuts on adjustment shields and replace side panels.

1.Remove electrical power supplied to the unit.

Remove electrical power supplied to the unit by unplug- ging the unit, or by turning off the wall circuit breaker. Turn off the main gas supply to the fryer and discon- nect and/or cap the main supply line to the fryer, or possible explosion could result.

2.Remove the left side panel of the fryer.

3.Using 11/16” wrench loosen fitting on gas line going to burner, and disconnect gas line.

4.Using a Phillips head screwdriver, remove the two screws securing the condensation deflector onto the frame and remove deflector.

5.Using 3/8” socket, remove nuts securing burner and drop burner off unit.

Image 66

Contents Page Specifications Henny Penny 8 Head GAS Pressure FryerPage Page Limited Warranty for Henny Penny Appliances Introduction Section Pressure IntroductionPressure Fryer HeatPage Page Page Prop UP a Ramp for Each Caster on the Selected Side Insert Page Page Page ALL STR N Unit again after installation Shortening MAY Start UP Procedure Lever Is not to be Pulled Page Page Push handle back and raise lid Cool Mode Switches IndicatorsLo Mode Melt Cycle OperationHeat Light will illuminate whenever the control calls for Page Refer to KFC’s Standards Library on cleaning instructions Page 397 Connecw Hj i’.,‘i ,e.*f Page Product Color Not Correct Too Dark Spotted Rancid Taste Shortening Too old Pressure will not Eplace pressure plate Replace module Heating of shortening too slow Or boil Water Shortening Ing over Gasket coming out of lid Pressure System Page Page Pump Position Check from Page Pressure Regulation Complete ControlPanel Henny Penny Every 90 daysPage Page Page LID Counterweight CONT’D Pressure PADLID Adjustment Hertz Page Seat ReplacementSolenoid Valve Operating Control ValveSafety Valve Do not Manuallyactivate the SafetyRemoval & Cleaning Operating ControlDo not Disassemble or Modify this Vavle Pressure GaugeCalibration Steps Page Page Page Page Page Page Page Page Page Using 3/8 socket, remove nut securing ground wire If no red glow is seen, proceed with the following Page Page Page Epyg-ui nuebq plea ewy Page Page Page Page Product One Units Part PER Number Description AssyLatch Plate PANEL, Right Side Page Not Avail Page Cable Counterweight BARPart PER Number Description CarriageHenny Penny Model 1005 LID Instruction Label LinkageassemblyUnits Part PER Number Description Assy CAM Slide FillerPage 705 Page Pressure Gauge Dead WeightFitting Connector Pipe ELBOW, 1/4Page BRACKET, HI-LIMIT LINK, Drain RODSUPPORT, Drain ROD HI-LIMITPage Units Smooth and Rounded Edge of Blade COVER, Coil Housing Solenoid ValveassemblyCORE, Disc Assembly HOUSING, CoilHead GAS Cooker I I SIE IAy--4A-+-7 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 SMS Programming IfApplicableCode After the load compensation, press and release the Func SMS Special Program Review UsageMode Mode Reset UsageFactory Presets F/C, Gas/Electric, Speaker Volume Speaker Frequency, Codes, Initialize SystemTech I/O Mode Appliance TestHeat Control Press and release the Function button and MELT, Mode