Henny Penny 680 KFC manual Rancid Taste Shortening Too old

Page 35

D. Rancid Taste

Shortening	too old.	Replace shortening,	and
		follow recommended	care
		and use of shortening.
Infrequent	filtering.	Replace shortening	and
		follow recommended	care
		and use of shortening.

General:

A.Meat Separation From Bone

B.Bone Color Not Proper

C. Breading Falls Off

D.Product Sticking Together

Non-compatible products cooked within the same shortening.

Raw product not fresh.

Incorrect meat cut.

Overcooking.

Product not fresh.

Using frozen product (black bone).

Improper processing of product (black bone).

Product not thoroughly cooked (red bone).

Incorrect breading

Product partially frozen.

Product breaded too long prior to cooking.

Improper loading procedure.

Wrong cook button pushed.

Replace shortening.

Use compatible products, and follow recommended care and use of shortening.

Use fresh product.

Use correct meat cutting procedures.

Check cooking time.

Use fresh product.

Use fresh product.

Use proper processing procedure for product.

Check cooking time.

Check cooking temperature.

Use correct breading

Thoroughly thaw the product, before breading.

*Refer to breading and frying instructions.

Properly load product per loading procedures.

Be sure to select the correct amount of product to be cooked.

Image 35

Contents Page Henny Penny 8 Head GAS Pressure Fryer SpecificationsPage Page Limited Warranty for Henny Penny Appliances Introduction Section Heat IntroductionPressure Fryer PressurePage Page Page Prop UP a Ramp for Each Caster on the Selected Side Insert Page Page Page ALL STR N Unit again after installation Shortening MAY Start UP Procedure Lever Is not to be Pulled Page Page Push handle back and raise lid Melt Cycle Operation Switches IndicatorsLo Mode Cool ModeHeat Light will illuminate whenever the control calls for Page Refer to KFC’s Standards Library on cleaning instructions Page 397 Connecw Hj i’.,‘i ,e.*f Page Product Color Not Correct Too Dark Spotted Rancid Taste Shortening Too old Pressure will not Eplace pressure plate Replace module Heating of shortening too slow Or boil Water Shortening Ing over Gasket coming out of lid Pressure System Page Page Pump Position Check from Page Every 90 days Complete ControlPanel Henny Penny Pressure RegulationPage Page Page Pressure PAD LID Counterweight CONT’DLID Adjustment Hertz Page Operating Control Valve ReplacementSolenoid Valve SeatOperating Control Do not Manuallyactivate the SafetyRemoval & Cleaning Safety ValveCalibration Steps Do not Disassemble or Modify this VavlePressure Gauge Page Page Page Page Page Page Page Page Page Using 3/8 socket, remove nut securing ground wire If no red glow is seen, proceed with the following Page Page Page Epyg-ui nuebq plea ewy Page Page Page Page Product One Part PER Number Description Assy UnitsLatch Plate PANEL, Right Side Page Not Avail Page Carriage Counterweight BARPart PER Number Description CableHenny Penny Model 1005 CAM Slide Filler LinkageassemblyUnits Part PER Number Description Assy LID Instruction LabelPage 705 Page Pipe ELBOW, 1/4 Dead WeightFitting Connector Pressure GaugePage HI-LIMIT LINK, Drain RODSUPPORT, Drain ROD BRACKET, HI-LIMITPage Units Smooth and Rounded Edge of Blade HOUSING, Coil Solenoid ValveassemblyCORE, Disc Assembly COVER, Coil HousingHead GAS Cooker I I SIE IAy--4A-+-7 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Code SMS ProgrammingIfApplicable After the load compensation, press and release the Func Mode SMS Special ProgramReview Usage Speaker Frequency, Codes, Initialize System Reset UsageFactory Presets F/C, Gas/Electric, Speaker Volume ModeHeat Control Tech I/O ModeAppliance Test Press and release the Function button and MELT, Mode