Henny Penny 680 KFC manual

Page 50

The Lid Counterweight in the back of the fryer balances the weight of the lid system to allow easier opening and closing of the lid. The weight has two cables attached to it, and weighs about 150 lbs. (67.5 Kg). One cable is centered on the weight and is the cable being used. The other cable is a safety cable and is off center. In case the main cable becomes loose or broken, the safety cable catches the weight and puts the weight into a bind, not allowing the lid to be opened or closed.

1.Using a 3/8” socket, remove the back shroud of the fryer.

2.With one person holding the weight level, another person locks the lid down.

3.Unthread the broken cable from the weight and the bracket attached to the fryer, and remove broken cable.

4.Thread a 5116” nut on each end of the new cable.

5.Screw the new cable into the weight, using a wrench, until it is tight.

6.Using a l/2” wrench, tighten the nut (already threaded on the cable) against the weight securing the cable into the weight.

7.Pull cable over pulley and down behind the weight.

8.Thread the other end of the cable through a 5116” nut on the underside of the bracket.

9.Tighten the cable up by screwing the cable through the nut, until the weight becomes level.

Image 50
Contents Page Specifications Henny Penny 8 Head GAS Pressure FryerPage Page Limited Warranty for Henny Penny Appliances Introduction Section Pressure IntroductionPressure Fryer HeatPage Page Page Prop UP a Ramp for Each Caster on the Selected Side Insert Page Page Page ALL STR N Unit again after installation Shortening MAY Start UP Procedure Lever Is not to be Pulled Page Page Push handle back and raise lid Cool Mode Switches IndicatorsLo Mode Melt Cycle OperationHeat Light will illuminate whenever the control calls for Page Refer to KFC’s Standards Library on cleaning instructions Page 397 Connecw Hj i’.,‘i ,e.*f Page Product Color Not Correct Too Dark Spotted Rancid Taste Shortening Too old Pressure will not Eplace pressure plate Replace module Heating of shortening too slow Or boil Water Shortening Ing over Gasket coming out of lid Pressure System Page Page Pump Position Check from Page Pressure Regulation Complete ControlPanel Henny Penny Every 90 daysPage Page Page LID Counterweight CONT’D Pressure PADLID Adjustment Hertz Page Seat ReplacementSolenoid Valve Operating Control ValveSafety Valve Do not Manuallyactivate the SafetyRemoval & Cleaning Operating ControlCalibration Steps Do not Disassemble or Modify this VavlePressure Gauge Page Page Page Page Page Page Page Page Page Using 3/8 socket, remove nut securing ground wire If no red glow is seen, proceed with the following Page Page Page Epyg-ui nuebq plea ewy Page Page Page Page Product One Units Part PER Number Description AssyLatch Plate PANEL, Right Side Page Not Avail Page Cable Counterweight BARPart PER Number Description CarriageHenny Penny Model 1005 LID Instruction Label LinkageassemblyUnits Part PER Number Description Assy CAM Slide FillerPage 705 Page Pressure Gauge Dead WeightFitting Connector Pipe ELBOW, 1/4Page BRACKET, HI-LIMIT LINK, Drain RODSUPPORT, Drain ROD HI-LIMITPage Units Smooth and Rounded Edge of Blade COVER, Coil Housing Solenoid ValveassemblyCORE, Disc Assembly HOUSING, CoilHead GAS Cooker I I SIE IAy--4A-+-7 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Code SMS ProgrammingIfApplicable After the load compensation, press and release the Func Mode SMS Special ProgramReview Usage Mode Reset UsageFactory Presets F/C, Gas/Electric, Speaker Volume Speaker Frequency, Codes, Initialize SystemHeat Control Tech I/O ModeAppliance Test Press and release the Function button and MELT, Mode