Henny Penny 680 KFC manual

Page 21

Gauge

Solenoid Valve

Drain Valve

Drain Interlock Switch

Condensation Drain Pan

The pressure gauge indicates the pressure inside the cookpot.

The solenoid valve is an electro-mechanical device that causes pressure to be held in the cookpot.

The solenoid valve closes at the beginning of the frying cycle and is opened automatically at the end of the frying cycle. If this valve should become dirty or the teflon seat nicked, pressure will not build up and it must be repaired per the maintenance section.

The drain valve is a two-way ball valve. It is normally in the

.closed position. Pull the knob out to drain the shortening from the cookpot into the filter drain pan.

DO NOT OPEN THE DRAIN VALVE WHILE COOKPOT IS UNDER PRESSURE. Hot shortening will exhaust from this valve. Severe burns will result.

The drain interlock switch is a microswitch that provides protection for the cookpot in the event an operator inadver- tently drains the shortening from the cookpot while the main switch is in the POWER position. The switch is designed to automatically shut off the heat when the dram valve is opened.

The condensation drain pan is the collection point for the condensation formed within the steam exhaust system. It must be removed and emptied periodically.

The lid stop bracket stops the upward motion of the lid assembly. This allows the lid to be lifted to an upright position with the rack removed allowing easier access to the cookpot for filtering and cleaning.

Image 21

Contents Page Henny Penny 8 Head GAS Pressure Fryer SpecificationsPage Page Limited Warranty for Henny Penny Appliances Introduction Section Pressure Fryer IntroductionPressure HeatPage Page Page Prop UP a Ramp for Each Caster on the Selected Side Insert Page Page Page ALL STR N Unit again after installation Shortening MAY Start UP Procedure Lever Is not to be Pulled Page Page Push handle back and raise lid Lo Mode Switches IndicatorsCool Mode Melt Cycle OperationHeat Light will illuminate whenever the control calls for Page Refer to KFC’s Standards Library on cleaning instructions Page 397 Connecw Hj i’.,‘i ,e.*f Page Product Color Not Correct Too Dark Spotted Rancid Taste Shortening Too old Pressure will not Eplace pressure plate Replace module Heating of shortening too slow Or boil Water Shortening Ing over Gasket coming out of lid Pressure System Page Page Pump Position Check from Page Panel Henny Penny Complete ControlPressure Regulation Every 90 daysPage Page Page Pressure PAD LID Counterweight CONT’DLID Adjustment Hertz Page Solenoid Valve ReplacementSeat Operating Control ValveRemoval & Cleaning Do not Manuallyactivate the SafetySafety Valve Operating ControlDo not Disassemble or Modify this Vavle Pressure GaugeCalibration Steps Page Page Page Page Page Page Page Page Page Using 3/8 socket, remove nut securing ground wire If no red glow is seen, proceed with the following Page Page Page Epyg-ui nuebq plea ewy Page Page Page Page Product One Part PER Number Description Assy UnitsLatch Plate PANEL, Right Side Page Not Avail Page Part PER Number Description Counterweight BARCable CarriageHenny Penny Model 1005 Units Part PER Number Description Assy LinkageassemblyLID Instruction Label CAM Slide FillerPage 705 Page Fitting Connector Dead WeightPressure Gauge Pipe ELBOW, 1/4Page SUPPORT, Drain ROD LINK, Drain RODBRACKET, HI-LIMIT HI-LIMITPage Units Smooth and Rounded Edge of Blade CORE, Disc Assembly Solenoid ValveassemblyCOVER, Coil Housing HOUSING, CoilHead GAS Cooker I I SIE IAy--4A-+-7 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 SMS Programming IfApplicableCode After the load compensation, press and release the Func SMS Special Program Review UsageMode Factory Presets F/C, Gas/Electric, Speaker Volume Reset UsageMode Speaker Frequency, Codes, Initialize SystemTech I/O Mode Appliance TestHeat Control Press and release the Function button and MELT, Mode