Henny Penny 680 KFC manual

Page 76

5.Depress the EXIT FILL button to exit the special program mode. Unit will return to stand-by cook mode.

The preceding steps must be followed exactly to enter the special program mode.

1.Enter the special program mode.

2.Depress the cycle 6 button. Display will read as follows.

DISPLAY E or 0 F or C BLANK BLANK

Digit4 32 1

Digit 1: Blank - When depressed, it will enter all KFC “Big Bird” parameters. Display will read INIT for two seconds,then 2-75 for two seconds.

Digit 2: Blank - When depressed, it will enter all KFC cook- ing parameters. Display will read INIT for two seconds, then Z-50 for two seconds.

Digit 3: Display will read either F for Fahrenheit degrees, or C for Celsius degrees.

Digit 4: Display will read either E for Electric or 0 for Other (includes Gas).

1.Enter the special program mode.

2.Depress the product 7 button. Display will be blank.

3.Depressing a certain button on the front pannel turns an output on, while depressing the same button again turns that output off. This will test all circuits on the controller.

The table below shows the corresponding button with the output.

To avoid personal injuries or property damage when performing the solenoid and heat control test, be sure there is shortening in the cookpot. The heat could run uncontrolled. For test purposes only.

Image 76
Contents Page Specifications Henny Penny 8 Head GAS Pressure FryerPage Page Limited Warranty for Henny Penny Appliances Introduction Section Introduction Pressure FryerPressure HeatPage Page Page Prop UP a Ramp for Each Caster on the Selected Side Insert Page Page Page ALL STR N Unit again after installation Shortening MAY Start UP Procedure Lever Is not to be Pulled Page Page Push handle back and raise lid Switches Indicators Lo ModeCool Mode Melt Cycle OperationHeat Light will illuminate whenever the control calls for Page Refer to KFC’s Standards Library on cleaning instructions Page 397 Connecw Hj i’.,‘i ,e.*f Page Product Color Not Correct Too Dark Spotted Rancid Taste Shortening Too old Pressure will not Eplace pressure plate Replace module Heating of shortening too slow Or boil Water Shortening Ing over Gasket coming out of lid Pressure System Page Page Pump Position Check from Page Complete Control Panel Henny PennyPressure Regulation Every 90 daysPage Page Page LID Counterweight CONT’D Pressure PADLID Adjustment Hertz Page Replacement Solenoid ValveSeat Operating Control ValveDo not Manuallyactivate the Safety Removal & CleaningSafety Valve Operating ControlPressure Gauge Do not Disassemble or Modify this VavleCalibration Steps Page Page Page Page Page Page Page Page Page Using 3/8 socket, remove nut securing ground wire If no red glow is seen, proceed with the following Page Page Page Epyg-ui nuebq plea ewy Page Page Page Page Product One Units Part PER Number Description AssyLatch Plate PANEL, Right Side Page Not Avail Page Counterweight BAR Part PER Number DescriptionCable CarriageHenny Penny Model 1005 Linkageassembly Units Part PER Number Description AssyLID Instruction Label CAM Slide FillerPage 705 Page Dead Weight Fitting ConnectorPressure Gauge Pipe ELBOW, 1/4Page LINK, Drain ROD SUPPORT, Drain RODBRACKET, HI-LIMIT HI-LIMITPage Units Smooth and Rounded Edge of Blade Solenoid Valveassembly CORE, Disc AssemblyCOVER, Coil Housing HOUSING, CoilHead GAS Cooker I I SIE IAy--4A-+-7 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 IfApplicable SMS ProgrammingCode After the load compensation, press and release the Func Review Usage SMS Special ProgramMode Reset Usage Factory Presets F/C, Gas/Electric, Speaker VolumeMode Speaker Frequency, Codes, Initialize SystemAppliance Test Tech I/O ModeHeat Control Press and release the Function button and MELT, Mode