Henny Penny 680 KFC manual 705

Page 88

Henny Penny

Model 680

FIGURE			UNITS
& ITEM	PART		PER
NO.	NUMBER	DESCRIPTION	ASSY.
1	35686	TUBE, DW to Exhaust Stack SS	1
2	MS01-297	HOSE CLAMP, SS - .500 – 1.062 DID	4
3	35693	TUBE, Exhaust Connect	1
4	35696	WELDMENT, Steam Exhaust Box Lid	1
5	SC02-014	SCREW, #8 AB x 3/8 P THD SS	4
6	35687	WELDMENT, Steam Exhaust Box	1
7	35694	TUBE, Condensate	1
8	70312	ASSEMBLY, Restrictor Weld	1
9	MS01-315	HOSE CLAMP, ½ x 1-3/4 SS	2
10	NS01-011	NUT, (#10-32 Hex)	1
11	36851	BRACKET, Hose	1
12	21877	TUBING, Steam Exhaust	4

705

6-15

Image 88

Contents Page Specifications Henny Penny 8 Head GAS Pressure FryerPage Page Limited Warranty for Henny Penny Appliances Introduction Section Introduction Pressure FryerPressure HeatPage Page Page Prop UP a Ramp for Each Caster on the Selected Side Insert Page Page Page ALL STR N Unit again after installation Shortening MAY Start UP Procedure Lever Is not to be Pulled Page Page Push handle back and raise lid Switches Indicators Lo ModeCool Mode Melt Cycle OperationHeat Light will illuminate whenever the control calls for Page Refer to KFC’s Standards Library on cleaning instructions Page 397 Connecw Hj i’.,‘i ,e.*f Page Product Color Not Correct Too Dark Spotted Rancid Taste Shortening Too old Pressure will not Eplace pressure plate Replace module Heating of shortening too slow Or boil Water Shortening Ing over Gasket coming out of lid Pressure System Page Page Pump Position Check from Page Complete Control Panel Henny PennyPressure Regulation Every 90 daysPage Page Page LID Counterweight CONT’D Pressure PADLID Adjustment Hertz Page Replacement Solenoid ValveSeat Operating Control ValveDo not Manuallyactivate the Safety Removal & CleaningSafety Valve Operating ControlPressure Gauge Do not Disassemble or Modify this VavleCalibration Steps Page Page Page Page Page Page Page Page Page Using 3/8 socket, remove nut securing ground wire If no red glow is seen, proceed with the following Page Page Page Epyg-ui nuebq plea ewy Page Page Page Page Product One Units Part PER Number Description AssyLatch Plate PANEL, Right Side Page Not Avail Page Counterweight BAR Part PER Number DescriptionCable CarriageHenny Penny Model 1005 Linkageassembly Units Part PER Number Description AssyLID Instruction Label CAM Slide FillerPage 705 Page Dead Weight Fitting ConnectorPressure Gauge Pipe ELBOW, 1/4Page LINK, Drain ROD SUPPORT, Drain RODBRACKET, HI-LIMIT HI-LIMITPage Units Smooth and Rounded Edge of Blade Solenoid Valveassembly CORE, Disc AssemblyCOVER, Coil Housing HOUSING, CoilHead GAS Cooker I I SIE IAy--4A-+-7 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 Henny Penny Model 501 IfApplicable SMS ProgrammingCode After the load compensation, press and release the Func Review Usage SMS Special ProgramMode Reset Usage Factory Presets F/C, Gas/Electric, Speaker VolumeMode Speaker Frequency, Codes, Initialize SystemAppliance Test Tech I/O ModeHeat Control Press and release the Function button and MELT, Mode