Alamo DSEB-D16/SAS instruction manual Components contain or emit chemicals known to the state

Page 12
(SG-38)
(SG-34)

 

SAFETY

 

 

 

 

DANGER!

NEVER use drugs or alcohol immediately before or while operating the

 

Tractor and Implement. Drugs and alcohol will affect an operator’s

 

alertness and coordination and therefore affect the operator’s ability to

 

operate the equipment safely. Before operating the Tractor or Imple-

 

ment, an operator on prescription or over-the-counter medication must

 

consult a medical professional regarding any side effects of the medi-

 

cation that would hinder their ability to operate the Equipment safely.

 

NEVER knowingly allow anyone to operate this equipment when their

 

alertness or coordination is impaired. Serious injury or death to the

 

operator or others could result if the operator is under the influence of

 

drugs or alcohol. (SG-27)

DANGER!

Operate the Tractor and/or Implement controls only while properly seated

 

in the Tractor seat with the seat belt securely fastened around you.

 

Inadvertent movement of the Tractor or Implement may cause serious

 

injury or death. (SG-29)

WARNING!

Engine Exhaust, some of its constituents, and certain vehicle

 

components contain or emit chemicals known to the state of

 

California to cause cancer and birth defects or other

 

reproductive harm. (SG-30)

WARNING!

Battery posts, terminals and related accessories contain lead

 

and lead compounds, chemicals known to the state of Califor-

 

nia to cause cancer and birth defects or other reproductive

 

harm. Wash Hands after handling. (SG-31)

WARNING!

Use extreme caution when getting onto the Implement to perform repairs, maintenance and

 

when removing accumulated material. Only stand on solid flat surfaces to ensure good footing.

 

Use a ladder or raised stand to access high spots which cannot be reached from gound level.

 

Slipping and falling can cause serious injury or death. (SG-33)

WARNING!

WARNING!

Avoid contact with hot surfaces including hydraulic oil tanks, pumps, motors, valves and hose connections. Relieve hydraulic pressure before performing maintenance or repairs. Use gloves and eye protection when servicing hot components. Contact with a hot surface or fluid can cause serious injury from burns or scalding.

Avoid contact with hot surfaces of the engine or muffler. Use gloves and eye protection when servicing hot components. Contact with a hot surface or fluid can cause serious injury from burns or scalding.

A-Boom (JD 6615 / 7615 Asy Instruction Manual) 07/03

© 2003 Alamo Group Inc.

Safety Section - 6

Image 12
Contents Boom John Deere 6615To the OWNER/OPERATOR/DEALER Introduction Index Assembly Instruction Safety Section Operation SafetyFilling Hydraulic Tank w/Oil 11-2 to Index Safety Section Safety 2003Alamo Group Inc SG-23 Death Components contain or emit chemicals known to the state Boom Assembly Tools, Supplies and Equipment Needed Paint Scraper to remove Paint before welding. RecommendedSaftey Equipment Frame and BoomHydraulic System Rotary Mower HeadFlail Mower Head Tractor Mower Operation InspectionPost-Operation Inspection Tractor Mower Component Location Wheel Weight Installation Rear Wheel Counter Weight Fill Left Rear Wheel with LiquidQty Description Installing Wheel Weight Alamo Group Inc Front Pump Drive Shaft Installation BoomPump / Drive Assembly Instructions Installing Pump, Pump Drive Components and Hydraulic TankInstalling Pump Drive Components Drive Shaft Assembly Installing Pump Mount Plate & Tube End of Driveshaft Plate # 02976087 standard mount plate SeeInstalling Pump See Figure Install Front frame Rail Supports Alamo Group Inc Frame Rail / High Frame Setup / Pre- Assembly Installation Frame Rail Set Up Frame Rail Pre-AssemblyFrame Rail Installation Frame Stiiffener Kit High Frame Mounting Tube Componnets High Frame Installation High Frame & King Post Asy Pre-Installing Frame Rails Front Frame Rail Mount Pad Support Mount Floor Jack Frame Rail Installation Pre-Installing High Frame 24-1/2 Min Height frame to Hood High Frame Frame Rail Section Pre-Install Mounting Tubes for High Frame Item Part NoLine with Tack Welding Frame Rails Mounted the hole will be up. See Item Frame To the mounting Tube. See Figure Recheck that all components areRemove High Frame for Final Welding Remove High Frame for Welding Frame Rail Installation Alamo Group Inc Frame Rail & High Frame Final Installation Re-Install Frame Rails to Tractor Boom Rest Frame Rail Installation 4 WD See . Check that all Bolts and Nuts Are installedRe-Install High Frame to Tractor See Tighten LH & RH Side Frame Rail Hyd. Tank, CWT & Decal Final Installation Hyd. Tank CWT Installation Hydraulic Tank InstallationCounter Weight Installation Decal Installation Tank Decal InstallationTank Oil Level Sight Gauge Decal Part Number. See , 33Cab Decal Installation OFF Switch See FigureSide Window. See Figure Boom Installation Boom Installation Boom Installation / Boom HosesCutter Motor Control Valve Asy Attach Swing Hose Installation Pump / Tank Hose InstallationReturn Hose Pressure Gauge Alamo Group Inc Cylinder Control Valve Installation StandardCylinder Control Valve Installation Control Handle Assembly InstallationController assemblies will be bolted On OFF Switch Installation Common Problems Standard Control Valve OperationSpool Valve Shown System Schematic Cylinder Hydraulic Control Circuit See Figures 2Cylinder Hydraulic Control Circuit See Cylinder Hydraulic Control Circuit Mechanical Valve ModelsCylinder Control Valve Installation Remote Cable Operation and Installation Control Assembly Controller End Installation Procedure Tractor FrontAlamo Group Inc Optional Joystick Wire Harness & Valve Installation Optional Joystick Mounting Cushion Removed Three Existing HolesInstalling Joystick Mount to Trac- tor Seat Option Joystick MountingInstallingJoystick to Bracket Installing Wiring Harness for JoystickJoystick Mounting 2 WD & 4 WD Wire Harness Through Cab. There is a Installing Wiring Harness to Joystick Align the Plug GuidesInstalling Warning Instruction Decals 02967827 02965262Wire Harness / Valve Mounting 2 WD & 4 WD Installing Wire Harness To ValveInstalling Wire Harness To ValveBOOM, Disregard this Section Joystick w/ Push/Pull Motor Switch & Rocker Master Switch Joystick Plug Bottom of Joystick ConsoleWire Harness Joystick Console Plug to Valve Control Valve Electric / Hydraulic Control Valves See FigureAlamo Group Inc Head Installation Optional Heads Optional Mower Head Installation Attaching Flail-Axe HeadAttaching Flail Head Attaching Ditcher Head Alamo Group Inc Frame Square Head Attachment Fill Hydraulic Tank Fill Hydraulic Tank Fill Hydraulic Tank with OilFill Hydraulic Tank Alamo Group Inc Hydraulic Start-Up Procedures Start-up Instructions Post-Assembly Check List Alamo Group Inc Boom Rest Plate Boom Swing Stop Installation Boom Rest Plate & Hook Installation Boom Rest Plate installationBoom Marked Here HereBolt on Boom Rest Hook Clamp Boom Swing Stop Installation Boom Swing Stop installationTack Weld Boom Swing Stop Lug. Tack Alamo Group Inc Alamo Group Inc Page Boom JD 6615 & JD7615 Assembly Manual Edition