Alamo DSEB-D16/SAS instruction manual Mounted the hole will be up. See Item

Page 47

Frame Rail Installation

Tack Welding Frame Rails: (continued)

4.Frame Stiffener Assembly. The frame stiffener is an assembly designed to run under the Tractor to tie the two Frame Rails together and support each other. The Gusset Rail Support is designed to stabilize the Frame Rails to the tractor frame. Re-check the left hand and right hand sides to make sure the alignment is still correct and the tack Welding has been performed.

 

Vertical Tube of RH Frame Rail

Front Wheel End

C-Clamp Here

 

 

 

 

 

Rear Axle End

Tack Weld here on both

 

Horizontal Tube

sides Front and Back only

 

Gusset Rail Support

after alignment

 

 

 

Align Flush with Bottom

 

Tack Weld Here

 

after final

of Vertical Tube

 

assembly only

RH Rail Stiffener Weldment (RH Side)

 

Rail Stiffener Tube Crossmember

 

 

 

LH Frame Rail is

LH Rail Stiffener Weldment

Mounted Here

Figure 39

(LH Side)

 

 

 

5.Locate Mounting Tubes and Hardware. See Figure 31 for breakdown of these components.

A.There will be one Mounting Tube for each side; these tubes are the same so it will not matter which is on which side. The Mounting Tubes are the same on either end. (See

Figure 31 - Item 1).

B.There will be 8 Bar Mounting Straps (Part # 02966639); these straps are the same but later in the assembly process 2 will have to be cut (See Figure 31 - Item 2 & 2A).

C.

There are 2 Angle Mounts (Part # 02966641), these have two holes in them and when

 

mounted the hole will be up. (See Figure 31 - Item 5).

D.There are 8 bolts (Part # 02957039) & Locknuts (Part # 00037200), the bolts are 3/4" X 10-1/2" Long (See Figure 31 - Item 4).

A-Boom (JD 6615 / 7615 Asy Instruction Manual) 07/03

© 2003 Alamo Group Inc.

Section 4 - 18

Image 47
Contents John Deere 6615 BoomTo the OWNER/OPERATOR/DEALER Introduction Safety Section Operation Safety Index Assembly InstructionFilling Hydraulic Tank w/Oil 11-2 to Index Safety Section Safety 2003Alamo Group Inc SG-23 Death Components contain or emit chemicals known to the state Boom Paint Scraper to remove Paint before welding. Recommended Assembly Tools, Supplies and Equipment NeededRotary Mower Head Saftey EquipmentFrame and Boom Hydraulic SystemPost-Operation Inspection Flail Mower HeadTractor Mower Operation Inspection Tractor Mower Component Location Wheel Weight Installation Qty Description Rear Wheel Counter WeightFill Left Rear Wheel with Liquid Installing Wheel Weight Alamo Group Inc Boom Front Pump Drive Shaft InstallationInstalling Pump Drive Components Pump / Drive Assembly InstructionsInstalling Pump, Pump Drive Components and Hydraulic Tank Drive Shaft Assembly Plate # 02976087 standard mount plate See Installing Pump Mount Plate & Tube End of DriveshaftInstalling Pump See Figure Install Front frame Rail Supports Alamo Group Inc Frame Rail / High Frame Setup / Pre- Assembly Installation Frame Rail Pre-Assembly Frame Rail Set UpFrame Rail Installation Frame Stiiffener Kit High Frame Mounting Tube Componnets High Frame Installation High Frame & King Post Asy Pre-Installing Frame Rails Front Frame Rail Mount Pad Support Mount Floor Jack Frame Rail Installation Pre-Installing High Frame 24-1/2 Min Height frame to Hood High Frame Frame Rail Section Item Part No Pre-Install Mounting Tubes for High FrameLine with Tack Welding Frame Rails Mounted the hole will be up. See Item Frame Recheck that all components are To the mounting Tube. See FigureRemove High Frame for Final Welding Remove High Frame for Welding Frame Rail Installation Alamo Group Inc Frame Rail & High Frame Final Installation Re-Install Frame Rails to Tractor Boom Rest See . Check that all Bolts and Nuts Are installed Frame Rail Installation 4 WDRe-Install High Frame to Tractor See Tighten LH & RH Side Frame Rail Hyd. Tank, CWT & Decal Final Installation Counter Weight Installation Hyd. Tank CWT InstallationHydraulic Tank Installation Decal Part Number. See , 33 Decal InstallationTank Decal Installation Tank Oil Level Sight GaugeSide Window. See Figure Cab Decal InstallationOFF Switch See Figure Boom Installation Cutter Motor Control Valve Asy Boom InstallationBoom Installation / Boom Hoses Attach Swing Pump / Tank Hose Installation Hose InstallationReturn Hose Pressure Gauge Alamo Group Inc Standard Cylinder Control Valve InstallationController assemblies will be bolted Cylinder Control Valve InstallationControl Handle Assembly Installation On OFF Switch Installation Standard Control Valve Operation Common ProblemsSpool Valve Shown Cylinder Hydraulic Control Circuit See Figures 2 System SchematicCylinder Hydraulic Control Circuit See Mechanical Valve Models Cylinder Hydraulic Control CircuitCylinder Control Valve Installation Remote Cable Operation and Installation Tractor Front Control Assembly Controller End Installation ProcedureAlamo Group Inc Optional Joystick Wire Harness & Valve Installation Cushion Removed Three Existing Holes Optional Joystick MountingOption Joystick Mounting Installing Joystick Mount to Trac- tor SeatJoystick Mounting 2 WD & 4 WD InstallingJoystick to BracketInstalling Wiring Harness for Joystick Wire Harness Through Cab. There is a Align the Plug Guides Installing Wiring Harness to Joystick02967827 02965262 Installing Warning Instruction DecalsInstalling Wire Harness To Valve Wire Harness / Valve Mounting 2 WD & 4 WDTo Valve Installing Wire HarnessBOOM, Disregard this Section Joystick Plug Bottom of Joystick Console Joystick w/ Push/Pull Motor Switch & Rocker Master SwitchWire Harness Joystick Console Plug to Valve Control Valves See Figure Control Valve Electric / HydraulicAlamo Group Inc Head Installation Optional Heads Attaching Flail-Axe Head Optional Mower Head InstallationAttaching Flail Head Attaching Ditcher Head Alamo Group Inc Frame Square Head Attachment Fill Hydraulic Tank Fill Hydraulic Tank with Oil Fill Hydraulic TankFill Hydraulic Tank Alamo Group Inc Hydraulic Start-Up Procedures Start-up Instructions Post-Assembly Check List Alamo Group Inc Boom Rest Plate Boom Swing Stop Installation Boom Rest Plate installation Boom Rest Plate & Hook InstallationBoom Marked Here HereBolt on Boom Rest Hook Clamp Tack Weld Boom Swing Stop Lug. Tack Boom Swing Stop InstallationBoom Swing Stop installation Alamo Group Inc Alamo Group Inc Page Boom JD 6615 & JD7615 Assembly Manual Edition