AMD SC2200 manual Bit Description

General Configuration Block 32580B

Table 4-2. Multiplexing, Interrupt Selection, and Base Address Registers (Continued)

Bit Description

16 Delay HSYNC. HSYNC delay by two TFT clock cycles. 0: There is no delay on HSYNC.

1: HYSNC is delayed twice by rising edge of TFT clock. Enables delay between VSYNC and HSYNC suited for TFT dis- play.

15 Reserved. Write as read.

14 IBUS16 (Invert BUS16). This bit inverts the meaning of MCR[3] (bit 3 of this register). 0: BUS16 is as described for MCR[3].

1: BUS16 meaning is inverted: if MCR[3] = 0, ROMCS# access is 16 bits wide; if MCR[3] = 1, ROMCS# access is 8 bits wide.

13 Reserved. Must be set to 0.

12 IO1ZWS (Enable ZWS# for IOCS1# Access). This bit enables internal activation of ZWS# (Zero Wait States) control for IOCS1# access.

0: ZWS# is not active for IOCS1# access.

1: ZWS# is active for IOCS1# access.

11 IO0ZWS (Enable ZWS# for IOCS0# Access). This bit enables internal activation of ZWS# (Zero Wait States) control for IOCS0# access.

0: ZWS# is not active for IOCS0# access.

1: ZWS# is active for IOCS0# access.

10 DOCZWS (Enable ZWS# for DOCCS# Access). This bit enables internal activation of ZWS# (Zero Wait States) control for DOCCS# access.

0: ZWS# is not active for DOCCS# access.

1: ZWS# is active for DOCCS# access.

9 ROMZWS (Enable ZWS# for ROMCS# Access). This bit enables internal activation of ZWS# (Zero Wait States) control for ROMCS# access.

0: ZWS# is not active for ROMCS# access.

1: ZWS# is active for ROMCS# access.

8 IO1_16 (Enable 16-Bit Wide IOCS1# Access). This bit enables the16-line access to IOCS1# in the Sub-ISA interface. 0: 8-bit wide IOCS1# access is used.

1: 16-bit wide IOCS1# access is used.

7 IO0_16 (Enable 16-Bit Wide IOCS0# Access). This bit enables the 16-line access to IOCS0# in the Sub-ISA interface. 0: 8-bit wide IOCS0# access is used.

1: 16-bit wide IOCS0# access is used.

6 DOC16 (Enable 16-Bit Wide DOCCS# Access). This bit enables the 16-line access to DOCCS# in the Sub-ISA interface. 0: 8-bit wide DOCCS# access is used.

1: 16-bit wide DOCCS# access is used.

5 Reserved. Write as read.

4 IRTXEN (Infrared Transmitter Enable). This bit enables drive of Infrared transmitter output. 0: IRTX+SOUT3 line (ball C11) is HIZ.

1: IRTX+SOUT3 line (ball C11) is enabled.

3 BUS16 (16-Bit Wide Boot Memory). (Read Only) This bit reports the status of the BOOT16 strap (ball C8). If the BOOT16 strap is pulled high, at reset 16-bit access to ROM in the Sub-ISA interface is enabled. MCR[14] = 1 inverts the meaning of this register.

0: 8-bit wide ROM.

1: 16-bit wide ROM.

2:1 Reserved. Write as read.

AMD Geode™ SC2200 Processor Data Book 81