Sub-ISA Interface, Sub-ISA Timing Parameters | AMD SC2200 guide

Electrical Specifications

32580B

9.3.6	Sub-ISA Interface
All output timing is guaranteed for 50 pF load, unless other-		The ISA Clock divisor (defined in F0 Index 50h[2:0] of the
wise specified.		Core Logic module) is 011.

Table 9-22. Sub-ISA Timing Parameters

		Bus
		Width		Min	Max
Symbol	Parameter	(Bits)	Type	(ns)	(ns)	Figure	Comments

tRD1	MEMR#/DOCR#/RD#/TRDE# Read	16	M	225		9-19	Standard
	active pulse width FE to RE

tRD2	MEMR#/DOCR#/RD#/TRDE# Read	16	M	105		9-19	Zero wait state
	active pulse width FE to RE

tRD3	IOR#/RD#/TRDE# Read active pulse	16	I/O	160		9-19	Standard
	width FE to RE

tRD4	IOR#/MEMR#/DOCR#/RD#/TRDE#	8	M, I/O	520		9-19	Standard
	Read active pulse width FE to RE

tRD5	IOR#/MEMR#/DOCR#/RD#/TRDE#	8	M, I/O	160		9-19	Zero wait state
	Read active pulse width FE to RE

tRCU1	MEMR#/DOCR#/RD#/TRDE#	16	M	103		9-19
	inactive pulse width

tRCU2	MEMR#/DOCR#/RD#/TRDE#	8	M	163		9-19
	inactive pulse width

tRCU3	IOR#/RD#/TRDE# inactive pulse	8, 16	I/O	163		9-19
	width

tWR1	MEMW#/WR# Write active pulse	16	M	225		9-20	Standard
	width FE to RE

tWR2	MEMW#/DOCW#/WR# Write active	16	M	105		9-20	Zero wait state
	pulse width FE to RE

tWR3	IOW#/WR# Write active pulse width	16	I/O	160		9-20	Standard
	FE to RE

tWR4	IOW#/MEMW#/DOCW#/WR# Write	8	M, I/O	520		9-20	Standard
	active pulse width FE to RE

tWR5	IOW#/MEMW#/DOCW#/WR# Write	8	M, I/O	160		9-20	Zero wait state
	active pulse width FE to RE

tWCU1	MEMW#/WR#/DOCW# inactive pulse	16	M	103		9-20
	width

tWCU2	MEMW#/WR#/DOCW# inactive pulse	8	M	163		9-20
	width

tWCU3	IOW#/WR# inactive pulse width	8, 16	I/O	163		9-20
tRDYH	IOR#/MEMR#/RD#/DOCR#/IOW#/	8, 16	M, I/O	120		9-19
	MEMW#/WR#/DOCW# Hold after					9-20
	IOCHRDY RE

tRDYA1	IOCHRDY valid after IOR#/MEMR#/	16	M, I/O		78	9-19
	RD#/DOCR#/IOW#/MEMW#/WR#/					9-20
	DOCW# FE

AMD Geode™ SC2200 Processor Data Book

397

Image 379

AMD SC2200 manual Sub-ISA Interface, Sub-ISA Timing Parameters, Bus Width Min, Symbol Parameter Bits Type Comments

Contents

AMD Geode SC2200 Processor Data Book Publication ID 32580B Contacts Trademarks Advanced Micro Devices, Inc. All rights reserved Contents Video Processor Module Electrical SpecificationsPackage Specifications Core Logic Module ACCESS.bus Data Transaction Power Supply ConnectionsTypical Battery Configuration Typical Battery Current Normal Operation Mode 325 Multiword DMA Data Transfer Timing Diagram 411Fast IR MIR and FIR Timing Diagram 428 Enhanced Parallel Port Timing Diagram 430 434 431432 433 32580B RTC Configuration Registers SIO Control and Configuration Register MapSIO Control and Configuration Registers Relevant RTC Configuration Registers 174 124Banks 0 and 1 Common Control and Status Registers 125 126 F3 PCI Header Registers for Audio Configuration Pciusb USB PCI Configuration Register SummaryF0BAR0+I/O Offset Gpio Configuration Registers F2BAR4+I/O Offset IDE Controller Configuration Registers PLL3 SuperI/O General DescriptionVideo Processor Core Logic Video Processor Module FeaturesGeneral Features GX1 Processor Module Overview Other FeaturesNand Eeprom SuperI/O Module 32580B Architecture Overview 32580B GX1 ModuleMemory Controller Video Processor Module SC2200 Memory Controller Register Summary Width Memory Offset Bits Type Name/Function Reset ValueSC2200 Memory Controller Registers MCMEMCNTRL2 R/W Rsvd Reserved. Write as GXBASE+840Ch-840Fh Bit Description GXBASE+8408h-840BhMcbankcfg R/W Rsvd Reserved. Write as 0070h Mcdradd R/W Mcgbaseadd R/WMcdracc R/W Video Input Port Fast-PCI BusDisplay 1 GX1 Module Interface Other Interfaces of the Core Logic Module System Reset Clock, Timers, and Reset LogicReset Logic Power-On Reset SC2200 Signal Definitions 32580BCRT Interface IDE/TFT Interface AMD Geode Jtag Interface USB Ball Assignments Signal Definitions LegendMnemonic Definition AMD Geode BGU481 Ball Assignment Sorted by Ball Number Configuration RD# Slct Buffer1 Power Signal Name VPD7 AD8 Inpci PWR AD0 Inpci AA4 IDEDATA5 MA9 AL8 SDATAIN2 Signal Name Ball No BGU481 Ball Assignment Sorted Alphabetically by Signal Name C30 FC/BE3# C17U31 B20 MD29 AD29 MD27 AC30MD28 AE31 C11 J28 F31J30 J29 Strap Options Nominal External PU/PD Strap SettingsStrap Options TFT, CRT, PCI, GPIO, System Multiplexing ConfigurationTwo-Signal/Group Multiplexing Default Alternate Ball No Signal Configuration Internal Test ACCESS.busAC97 Fpci Monitoring Three-Signal/Group Multiplexing Fpvddon Four-Signal/Group MultiplexingGxclk TEST3 Boot ROM is 16 Bits Wide. This strap signal enables Signal DescriptionsSignal Name Ball No Type Description Mux Maximum Core Clock Multiplier. These strap signals AH2 AJ2AJ3 AG3 Column Address Strobe. RAS#, CAS#, WE# and CKE Memory Interface Signals Video Port Interface Signals ACCESS.bus Interface Signals 4 CRT/TFT Interface Signals Multiplexed Command and Byte Enables. During PCI Bus Interface SignalsACCESS.bus 1 Serial Data. This is the bidirectional ACCESS.bus 2 Serial Data. This is the bidirectional TRDY# PARPERR# FRAME# IRDY# BHE# STOP#LOCK# DEVSEL# REQ0# PERR#SERR# REQ1# Sub-ISA Interface Signals Low Pin Count LPC Bus Interface Signals IDE Interface Signals Serial Ports UARTs Interface Signals Universal Serial Bus USB Interface Signals +SDTEST2 GPIO11+IRQ15DCD2# GPIO9+IDEIOW1# Parallel Port Interface Signals IRRX1 AK8 Fast Infrared IR Port Interface SignalsSTB#/WRITE# FFRAME# Serial Bus Synchronization. This bit is asserted to syn 14 AC97 Audio Interface SignalsPower Management Interface Signals General Purpose Wakeup I/Os. These signals each PWRCNT2 AL7 Suspend Power Plane Control 1 and 2. Control signalPWRBTN# AH5 PWRCNT1 AK6 Gpio Interface Signals System Management Interrupt. This is the input to Debug Monitoring Interface SignalsJtag Interface Signals Fast-PCI Bus Monitoring Signals. When enabled, this Power, Ground and No Connections1 Test and Measurement Interface Signals 3V Analog CRT DAC Power Connections. Low noise power 3V PLL2 Analog Power Connection. Low noise power for PLL23V PLL3 Analog Power Connection. Low noise power for PLL3 3V Analog USB Power Connection. Low noise power 32580B Width Offset Bits Configuration Block AddressesGeneral Configuration Block Register Summary General Configuration Block 32580B Fpcimon Ball # Internal Test Signals Name Add’l DependenciesOther Signal Add’l Dependencies PMR27 Ball # IDE Signals CRT, Gpio and TFT Signals Name General Configuration Block PP/ACB1/FPCI BitTFT Name Add’l Dependencies Rsvd Reserved. Write to Ball # Gpio Signals LPC Signals Name Add’l Dependencies Reserved 32580BGeneral Configuration Block Bit Description Offset 3Ch Interrupt Selection Register Intsel R/W Reset Value 00hReset Value xxh Offset 39h-3Bh Functional Description Watchdog Timer Usage Hints Watchdog RegistersWatchdog Interrupt 3describes the Watchdog registers High-Resolution Timer Registers High-Resolution TimerOffset 05h-07h Reserved Rsvd Bit Description Offset 08h-0Bh Reset Value xxxxxxxxhTmclksel Timer Clock Select Tmen Timer Interrupt Enable Clock Generators and PLLs Crystal Oscillator Circuit Components 1 27 MHz Crystal OscillatorComponent Parameters Values Tolerance Strapped Core Clock Frequency 2 GX1 Module Core ClockInternal Fast-PCI Clock Core Clock Frequency Core Logic Module Clocks SuperI/O ClocksVideo Processor Clocks Clock Registers Clock Generator Configuration9describes the registers of the clock generator and PLL 66.7 MHz 15141110 33.3 MHz ISA Outstanding FeaturesAB1C AB1D AB2C AB2D Serial Port 3 / Infrared IR Communication Port PC98 and Acpi CompliantParallel Port Serial Port Module Architecture AccessSignals Internal Internal Signals LDN Assignments Configuration Structure/AccessSIO Configuration Options Index-Data Register Pair Address Decoding Default Configuration Setup Standard Logical Device Configuration Registers Standard Configuration RegistersSIO Control and Configuration Registers Logical Device Control and Configuration Registers Standard Configuration Registers 102 Index F0h-FEh Logical Device Configuration R/W32580BSuperI/O Module DMA Channel Select 1 R/W SID. SIO ID SIO Control and Configuration RegistersSIO Control and Configuration Register Map Index Type Name Power Rail Reset Value Relevant RTC Configuration Registers Logical Device Control and Configuration RTC Configuration Registers LDN 01h System Wakeup Control Relevant SWC RegistersBase Address MSB register Relevant IRCP/SP3 Registers 10. IRCP/SP3 Configuration Register LDN 03h and 08h Serial Ports 1 12. Serial Ports 1 and 2 Configuration RegisterSerial Ports 1 and 2 Configuration register 11. Relevant Serial Ports 1 and 2 Registers 13. Relevant ACB1 and ACB2 Registers 14. ACB1 and ACB2 Configuration RegisterLDN 05h and 06h ACCESS.bus Ports 1 ACB1 and ACB2 Configuration register 15. Relevant Parallel Port Registers 16. Parallel Port Configuration Register RTC Clock Generation X32I External X32O Battery = 0.1 μFReal-Time Clock RTC Bus Interface External Oscillator Signal ParametersExternal Elements Oscillator Startup Leap Years AlarmsTimekeeping Data Format Daylight Saving RTC Power SupplyBT1 18. System Power States 116 Battery-Backed RAMs and RegistersInterrupt Handling Bit CRC Index Type Name RTC Registers19. RTC Register Map 20. RTC Registers 118 Hours Register HOR R/W Reset Type VPP PURIndex 05h Hours Alarm Register Hora R/W CRD is AMD Geode SC2200 Processor Data Book 119 Index Programmable Month Alarm Register Mona R/WIndex 0Ch RTC Control Register C CRC RO Index Programmable Century Register CEN R/W Parameter BCD Format Binary Format 21. Divider Chain Control / Test Selection22. Periodic Interrupt Rate Encoding 23. BCD and Binary Formats 25. Extended RAM Map 0Eh 7Fh Battery-backed general-purpose Byte RAM00h 7Fh Battery-backed general-purpose Byte RAM RTC General-Purpose RAM Map 24. Standard RAM Map Event Detection System Wakeup Control SWC26. Time Range Limits for Ceir Protocols Offset Type Name Value SWC Registers27. Banks 0 and 1 Common Control and Status Register Map Type Name Value 29. Banks 0 and 1 Common Control and Status Registers 30. Bank 1 Ceir Wakeup Configuration and Control Registers Ceir Wakeup Range 2 Registers Bit Description Ceir Wakeup Range 1 RegistersBank 1, Offset 0Ah IRWTR1L Register R/W Ceir Pulse Change, Range 1, High Limit AMD Geode SC2200 Processor Data Book 127 ACCESS.bus InterfaceData Transactions ABD ABC ABD MSB Acknowledge ACK CycleABC ACK Addressing Transfer Formats Master ModeAcknowledge After Every Byte Rule Arbitration on the Bus Master Stop Sending the Address ByteMaster Transmit Master Receive Configuration Slave Mode 31. ACB Register Map ACB Registers32. ACB Registers MASTER. RO Stop Stop Inten Interrupt EnableSaen Slave Address Enable EN Enable 34. Parallel Port Register Map for Second Level Offset Legacy Functional BlocksParallel Port 33. Parallel Port Register Map for First Level Offset 36. Parallel Port Bit Map for Second Level Offset 35. Parallel Port Bit Map for First Level Offset136 Type Name Uart Functionality SP1 and SP2 BSR Bits Bank Selected 38. Bank Selection Encoding39. Bank 1 Register Map 40. Bank 2 Register Map SHLCR. Shadow of LCR 41. Bank 3 Register Map42. Bank 0 Bit Map MRID. Module and Revision ID Register Bits Offset 43. Bank 1 Bit Map44. Bank 2 Bit Map 45. Bank 3 Bit Map IRCP/SP3 Register and Bit Maps 3.1 IR/SP3 Mode Register Bank Overview01h Register Throughout Offset 00h All Banks BSR Bits Bank Selected Functionality 47. Bank Selection Encoding48. Bank 1 Register Map 49. Bank 2 Register Map 51. Bank 4 Register Map 50. Bank 3 Register Map52. Bank 5 Register Map 54. Bank 7 Register Map 53. Bank 6 Register Map55. Bank 0 Bit Map 59. Bank 4 Bit Map 56. Bank 1 Bit Map57. Bank 2 Bit Map 58. Bank 3 Bit Map 61. Bank 6 Bit Map 60. Bank 5 Bit Map62. Bank 7 Bit Map Feature List Low Pin Count LPC Interface ConfigIntegrated Audio Video Processor Interface Pserial Interface Fast-PCI Interface to External PCI Bus Video Retrace Interrupt IDE Configuration RegistersPIO Mode IDE Controller Physical Region Descriptor Format DMARDY# Strobe Ideiordy UltraDMA/33 Signal DefinitionsUltraDMA/33 Mode Stop Docw Universal Serial BusSub-ISA Bus Interface IOCS0#/IOCS1# AD310 Read AD310 Write Sub-ISA Support of Delayed PCI TransactionsSub-ISA Bus Cycles Fast-PCICLK Sub-ISA Bus Data Steering 5.4 I/O Recovery DelaysREQ# GNT# FRAME# IRDY# TRDY# STOP# Bale ISA RD#, IOR# 158 ISA DMASD150 AD310 PCI PCI and Sub-ISA Signal Cycle MultiplexingCycle Multiplexed PCI / Sub-ISA Balls ROM Interface DMA Channels FRAME# TRDY#, IRDY#ROMCS#, DOCCS# IOCS0#, IOCS1# PAR DEVSEL#,STOP# DMA Controller DMA Priority DMA Transfer ModesDMA Controller Registers DMA Transfer Types DMA Address Generation Programmable Interval TimerDMA Addressing Capability DMA Page Registers and Extended Addressing Mapping PIC Interrupt MappingProgrammable Interrupt Controller Master PCI Compatible Interrupts PIC Interrupt SequencePIC I/O Registers PIC Shadow Register 7.2 I/O Port 061h System Control Fast Keyboard Gate Address 20 and CPU ResetKeyboard Support 7.1 I/O Port 092h System Control Power Management Logic Wakeup Events Capability Power Planes vs. Sleep/Global States Power Planes Control Signals vs Sleep StatesPower Management Events AMD Geode SC2200 Processor Data Book 169 Power ButtonPower Button Override Thermal Monitoring Suspend Modulation Power Management ProgrammingCPU Power Management APM Support Save-to-Disk Volt SuspendAMD Geode SC2200 Processor Data Book 171 Acpi Timer Register Peripheral Power ManagementDevice Idle Timers and Traps General Purpose Timers Module Power Management SMI Status Reporting RegistersF1BAR0+I/O F1BAR0+I/O Device Power Management Programming SummaryPower Management Programming Summary Located at F0 Index xxh Unless Otherwise Noted Integrated Audio Gpio Interface Size 11. Physical Region Descriptor FormatByte Audio Data Buffer PRD3 PRD1 PRD2 AMD Geode SC2200 Processor Audio SMI Related Registers Trap SMI Enable RegisterVSA Technology Support Hardware VSA Technology Module Core Logic Module LPC Interface IRQ Configuration RegistersInternal IRQ Enable Register Internal IRQ Control Register 12. Cycle Types 13. PCI Configuration Address Register 0CF8h PCI Configuration Space and Access MethodsRegister Descriptions Register Summary Ter’s reset values and page references where the bit forMats are found AMD Geode SC2200 Processor Data Book 185 Width Reset Reference F0 Index Bits 186 32580BCore Logic Module Register Summary F0BAR1+ 15. F0BAR0 Gpio Support Registers Summary16. F0BAR1 LPC Support Registers Summary F0BAR0+ F1BAR0+ 18. F1BAR0 SMI Status Registers Summary 20h PM2CNT PM2 Control Register 00h 21h-FFh Not Used 19. F1BAR1 Acpi Support Registers SummaryF1BAR1+ 00h-03h Pcnt Processor Control Register 190 Width Reset Reference F2 Index Bits F2BAR4+ Width Reset Reference F3 Index Bits21. F2BAR4 IDE Controller Support Registers Summary 22. F3 PCI Header Registers for Audio Support Summary 192 Width Reset23. F3BAR0 Audio Support Registers Summary F3BAR0+ AMD Geode SC2200 Processor Data Book 193 Width Reset Reference F5 Index Bits25. F5BAR0 I/O Control Support Registers Summary F5BAR0+ Width Reference Index Bits 26. Pciusb USB PCI Configuration Register SummaryName Reset Value Pciusb USBBAR0 27. Usbbar USB Controller Registers SummaryAMD Geode SC2200 Processor Data Book 195 DMA Page Registers Table 28. ISA Legacy I/O Register Summary196 Keyboard Controller Registers Table Programmable Interval Timer Registers TablePort Type Name Reference Programmable Interrupt Controller Registers Table Bridge, GPIO, and LPC Registers Function Chipset Register SpaceGeneral Remarks AMD Geode SC2200 Processor Data Book 199 Core Logic Module Bridge, GPIO, and LPC Registers FunctionIndex 06h-07h PCI Status Register R/W Data Parity Detected. This bit is set when Index 0Ch Index 0Eh PCI Header Type RO Reset Value 80hBit Description Index 08h Index 09h-0Bh AMD Geode SC2200 Processor Data Book 201 202 Reset Control Register R/W Reset Value 01hIndex 42h Index 43h AMD Geode SC2200 Processor Data Book 203 PIT Counter 1 Enable Reset Value FFFFFFFFhReset Value 7Bh PIT Software Reset Generate SMI on A20M# Toggle ROM/AT Logic Control Register R/W Reset Value 98h 206 Index 5Bh Decode Control Register 2 R/W Index 5Dh Index 5ChINTB# Ball C26 Target Interrupt INTA# Ball D26 Target Interrupt 208 Reset Value 0000hIndex 72h Chip Select 1 Positive Decode IOCS1# Index 77h Index 74h-75hIndex 76h IOCS0# Control Register R/W O Chip Select 0 Positive Decode IOCS0# 210 Index 81h Power Management Enable Register 2 R/W AMD Geode SC2200 Processor Data Book 211 Keyboard/Mouse Access Trap Index 82h Power Management Enable Register 3 R/W212 Index 83h Power Management Enable Register 4 R/W Parallel/Serial Access TrapFloppy Disk Access Trap Primary Hard Disk Access Trap 214 Index 84h Second Level PME/SMI Status Mirror Register 1 RO AMD Geode SC2200 Processor Data Book 215 216 Reserved. Always reads Index 88h General Purpose Timer 1 Count Register R/WAMD Geode SC2200 Processor Data Book 217 Second Millisecond Re-trigger General Purpose Timer 1 on Floppy Disk Activity218 Index 8Dh Video Speedup Timer Count Register R/W Index 8Bh General Purpose Timer 2 Control Register R/WAMD Geode SC2200 Processor Data Book 219 Index 96h Index 8Fh-92hIndex 93h Index 94h-95h AMD Geode SC2200 Processor Data Book 221 Index 9Ah-9Bh Floppy Disk Idle Timer Count Register R/WIndex 97h Index 98h-99h Index AAh-ABh Reserved Reset Value 00h 222 Index A6h-A7h Video Idle Timer Count Register R/WIndex A8h-A9h Video Overflow Count Register R/W Index B4h Index AEh CPU Suspend Command Register WOIndex AFh Suspend Notebook Command Register WO Index B0h-B3h Index BAh PIT Shadow Register RO Index B9h PIC Shadow Register RO224 Index C0h-C3h Index BCh Clock Stop Control Register R/W Reset Value 00hReserved. Set to CPU Clock Stop Index BDh-BFh Index CFh Bit Description MaskIndex CDh Index CEh Index F5h Second Level PME/SMI Status Register 2 RC Second Level PME/SMI Status Register 1 RC Reset Value 00hAMD Geode SC2200 Processor Data Book 227 Reserved . Reads as Index F6h Second Level PME/SMI Status Register 3 RC228 Reserved. Read as Index F7h Second Level PME/SMI Status Register 4 RCAMD Geode SC2200 Processor Data Book 229 Reserved Reset Value 00h 230 Gpio Support Registers 30. F0BAR0+I/O Offset Gpio Configuration RegistersF0 Index 10h, Base Address Register 0 F0BAR0 points to 316 Reserved. Must be set to F0BAR0+I/O Offset 18h is set, this edge generates a PME232 010100 = GPIO20 balls A9, N31 000101 Bank010010 = GPIO18 ball AG1 000011 010011 = GPIO19 ball C9 000100 234 Reserved. Set to 31. F0BAR1+I/O Offset LPC Interface Configuration RegistersLPC Support Registers 3121 236 AMD Geode SC2200 Processor Data Book 237 Polarity selection 238 Reserved Serial IRQ EnableSerial IRQ Interface Mode Number of IRQ Data Frames AMD Geode SC2200 Processor Data Book 239 LPC Midi Address Select. Selects I/O Port LPC Game Port 1 Address Select. Selects I/O PortLPC Game Port 0 Address Select. Selects I/O Port LPC Floppy Disk Controller Address Select. Selects I/O Port AMD Geode SC2200 Processor Data Book 241 LPC Error Address 242 Offset 20h-23h Lpcerradd LPC Error Address Register RO 32. F1 PCI Header Registers for SMI Status and Acpi Support SMI Status and Acpi Registers Function SMI Status Support Registers 33. F1BAR0+I/O Offset SMI Status Registers246 Offset 02h-03h Top Level PME/SMI Status Register RO/RC Suspend Modulation Enable Mirror. Read to ClearAMD Geode SC2200 Processor Data Book 247 248 AMD Geode SC2200 Processor Data Book 249 Yes To enable SMI generation, set F0 Index 82h6 =Yes To enable SMI generation, set F0 Index 82h5 = Bit Description Offset 04h-05h 250 Offset 08h-09h SMI Speedup Disable Register Read to EnableOffset 0Ah-1Bh These addresses should not be written Offset 1Ch-1Fh Offset 22h-23h Second Level Acpi PME/SMI Status Register RC Bit Description Offset 20h-21hAMD Geode SC2200 Processor Data Book 251 252 Offset 24h-27h External SMI Register R/W Second level SMI status is reported at bits 21 RC and 13 RO Top level SMI status is reported at F1BAR0+00h/02h10Second level SMI status is reported at bits 23 RC and 15 RO Second level SMI status is reported at bits 22 RC and 14 RO Offset 50h-FFh Offset 28h-4Fh Not Used254 Clkval Clock Throttling Value. CPU duty cycle Offset 06h Smicmd OS/BIOS Requests Register R/W34. F1BAR1+I/O Offset Acpi Support Registers Acpi Support Registers 256 SCI generation is always enabled 1511 Offset 0Ah-0Bh PM1AEN PM1A PME/SCI Enable Register R/WAMD Geode SC2200 Processor Data Book 257 Reserved 258 AMD Geode SC2200 Processor Data Book 259 260 Offset 15h Gpwio Control Register 2 R/W Those selected GPIOs for generation of an SCIReserved AMD Geode SC2200 Processor Data Book 261 3117 Gpwio Data Register R/W Reset Value 00h262 Read value for these registers is undefined Offset 21h-FFhAMD Geode SC2200 Processor Data Book 263 314 Bus Mastering IDE Base Address Reset Value 0502hReset Value 010180h IDE Controller Registers Function Core Logic Module IDE Controller Registers Function PIOMODE. PIO modeAMD Geode SC2200 Processor Data Book 267 268 Reset Value 00009172hReset Value 00077771h Index 48h-4Bh AMD Geode SC2200 Processor Data Book 269 Bit Description Index 50h-53hIndex 58h-5Bh Index 60h-FFh 270 IDE Controller Support Registers Offset 0Ch-0Fh Offset 09hOffset 0Ah Offset 0Bh Audio Registers Function 37. F3 PCI Header Registers for Audio Configuration Offset 04h-07h 38. F3BAR0+Memory Offset Audio Configuration RegistersAudio Support Registers Core Logic Module Audio Registers Function 274 AMD Geode SC2200 Processor Data Book 275 276 Offset 14h-17h Trap SMI and Fast Write Status Register RO/RC AMD Geode SC2200 Processor Data Book 277 278 Mask Internal IRQ10. Write Only Mask Internal IRQ15. Write OnlyMask Internal IRQ14. Write Only Mask Internal IRQ11. Write Only Reserved. Set to Assert Masked Internal IRQ12 Mask Internal IRQ4. Write OnlyMask Internal IRQ3. Write Only Assert Masked Internal IRQ14 AMD Geode SC2200 Processor Data Book 281 Bit Description Assert Masked Internal IRQ1 Offset 2Ch-2Fh Audio Bus Master 1 Command Register R/W Reset Value 00hOffset 29h Audio Bus Master 1 SMI Status Register RC Offset 2Ah-2Bh Offset 34h-37h Audio Bus Master 2 Command Register R/W Reset Value 00hOffset 31h Audio Bus Master 2 SMI Status Register RC Offset 32h-33h Offset 3Ch-3Fh Audio Bus Master 3 Command Register R/W Reset Value 00hOffset 39h Audio Bus Master 3 SMI Status Register RC Offset 3Ah-3Bh Offset 44h-47h Audio Bus Master 4 Command Register R/W Reset Value 00hOffset 41h Audio Bus Master 4 SMI Status Register RC Offset 42h-43h Offset 4Ch-4Fh Audio Bus Master 5 Command Register R/W Reset Value 00hOffset 49h Audio Bus Master 5 SMI Status Register RC Offset 4Ah-4Bh 39. F5 PCI Header Registers for X-Bus Expansion Bus Expansion Interface Function Index 28h-2Bh Bit Description Index 1Ch-1FhIndex 20h-23h Index 24h-27h Index 50h-53h F5BAR4 Mask Address Register R/W Index 58h F5BARx Initialized Register R/W Reset Value 00hIndex 48h-4Bh F5BAR2 Mask Address Register R/W Index 4Ch-4Fh F5BAR3 Mask Address Register R/W 40. F5BAR0+I/O Offset X-Bus Expansion Registers Iostrapidselselect Idsel Strap Override Three USB transceivers. Default = 128USB transceivers. Default = Iotestporten Debug Test Port Enable USB Controller Registers Pciusb 41. Pciusb USB PCI Configuration Registers292 Bit Description Index 06h-07h Status Register R/W Reset Value 08hIndex 0Dh Latency Timer Register R/W Core Logic Module USB Controller Registers Pciusb Bit Description Index 10h-13h Reset Value 0E11hReset Value A0F8h Reset Value 50h Core Logic Module USB Controller Registers Pciusb 32580B 42. USBBAR+Memory Offset USB Controller RegistersAMD Geode SC2200 Processor Data Book 295 FrameNumberOverflowEnable HcInterruptEnable Register R/W Reset Value = 00000000hOwnershipChangeEnable RootHubStatusChangeEnable 297 Ignore Disable interrupt generation due to Resume DetectedIgnore Disable interrupt generation due to Start of Frame Offset 28h-2Bh Offset 38h-3Bh Reset Value = 00000628hReset Value = 01000003h Bit Description Offset 34h-37h AMD Geode SC2200 Processor Data Book 299 Read LocalPowerStatusChange. Not supported. Always readOffset 50h-53h HcRhStatus Register R/W 3018 300 AMD Geode SC2200 Processor Data Book HcRhPortStatus1 Register R/W Reset Value = 00000000hRead PortResetStatus Read PortSuspendStatus Read CurrentConnectStatus Read PortEnableStatusAMD Geode SC2200 Processor Data Book 301 302 319 Reserved. Read/Write 0s Reset Value = xxhOffset 60h-9Fh Offset 100h-103h 304 43. DMA Channel Control Registers ISA Legacy Register Space Write Priority ModeTiming Mode 32580BCore Logic Module ISA Legacy Register Space Address Direction Transfer ModeChannel Number Mode Select Bit Description Port 00Bh Undefined Write DMA Command Register, Channels308 Port 0D8h Bit Description Port 0D2hPort 0D4h Port 0D6h 44. DMA Page Registers 45. Programmable Interval Timer Registers Port 043h R/W Current Counter Mode BCD ModeBit Description Port 042h Write Counter Value Read 46. Programmable Interrupt Controller Registers IRQ1 / IRQ9 Mask Poll CommandRegister Read Mode Bit Description IRQ2 / IRQ10 Mask IRQ4 / IRQ12 In-Service Interrupt Service Register IRQ7 / IRQ15 In-ServiceIRQ6 / IRQ14 In-Service IRQ5 / IRQ13 In-Service 47. Keyboard Controller Registers 49. Miscellaneous Registers 48. Real-Time Clock Registers Bit Description Graphics-Video Overlay and Blending General FeaturesVideo Input Port VIP Hardware Video Acceleration Mixer/Blender VIP320 Video Processor Module Functional DescriptionVideo Support VBI Support Active Video Video Input Port VIP 1.1 Direct Video ModeGenLock Program other VIP bus master support registers Capture Video ModeBob Program the VIP bus master address registers Address not changed during runtime WeaveAMD Geode SC2200 Processor Data Book 325 Ping-pongs between the two buffers during runtime Field Interrupt Capture VBI Mode326 AMD Geode SC2200 Processor Data Book 327 Video BlockVideo Input Formatter Line Buffer Filtering Horizontal Downscaler with 4-Tap FilteringHorizontal Downscaler Ai,j Ai,j+1 Ai+1,jAi+1,j+1 Line BuffersFormatter 2.5 2-Tap Vertical and Horizontal Upscalers YUV Mixer/Blender BlockRGB RAM Color/Chroma Key Valid Mixing/Blending ConfigurationsYUV to RGB CSC in Video Data Path Gamma Correction Cursor Window Color/Chroma Key and Mixer/BlenderGraphics Window Video Window CHROMASEL1 Truth Table for Alpha BlendingMixing/Blending Operation Color 334 AMD Geode SC2200 Processor Data Book 335 Vesa DDSC2B and Dpms SupportIntegrated DACs Monitor T1 is a programmable multiple of frame time T0+T1 Power SequenceTFT Interface HSYNC, VSYNC, TFTDE, Tftdck AMD Geode SC2200 Processor Data Book 337 Divider Phase Charge LoopIntegrated PLL Compare Pump Filter Divider Out F4BAR0+ F4BAR0 Video Processor Configuration Registers SummaryWidth Reset Reference F4 Index Bits F4 PCI Header Registers for Video Processor Support Summary AMD Geode SC2200 Processor Data Book 339 Video Processor Module Register Summary 340 F4BAR2 VIP Support Registers Summary32580BVideo Processor Module Register Summary F4BAR2+ Video Processor Module Video Processor Registers Function Reset Value 0504hReset Value 030000h Video Processor Registers Function 342 Index 3Eh-FFh Reserved Video Processor Support Registers F4BAR0 Base address that allows PCI access to the Video ProcesF4 Index 10h, Base Address Register 0 F4BAR0 sets Ddcsdaout DDC Output Data. DDC data bit for output Offset 04h-07h Display Configuration Register R/WTions of the power sequence control lines 1614 3028 AMD Geode SC2200 Processor Data Book 345 Offset 08h-0Bh Video X Position Register R/W 346 Bit Description 100 Block Offset 20h-23h Reset Value 00001400h12 PLL2PWREN PLL2 Power-Down Enable Bit Description Offset 1Ch-1Fh FLTCO3 Filter Coefficient 3. For the tap-3 filter DTS Downscale Type SelectOffset 40h-43h Video Downscaler Coefficient Register R/W FLTCO4 Filter Coefficient 4. For the tap-4 filter Bit Description Offset 44h-47h CRC Signature Register R/W Reserved Signen Signature EnableReset Value 0000xxxxh Reset Value 00060000h 350 Top line is in even field. Default Top line is in odd fieldCursor Color Key Register R/W Reset Value 00000000h 100 i.e., shift one line otherwise, leave at Reserved AMD Geode SC2200 Processor Data Book 351 Incoming graphics stream to be ignoredOffset 60h-63h Alpha Window 1 X Position Register R/W 3125 Decremented until it is reloaded via bit 17 Loadalpha 3118Reserved 352 Reserved AMD Geode SC2200 Processor Data Book 353 Video Fifo Underflow Empty Offset 90h-93hOffset 94h-97h Offset 400h-403h Offset 408h-40Bh Reserved. Set to Genlocktouten GenLock Timeout EnableCtgenlocken Enable Continuous GenLock Function Offset 404h-407h F4BAR0+Memory Offset Video Processor Configuration Registers AMD Geode SC2200 Processor Data Book 357 F4BAR2+Memory Offset VIP Configuration RegistersVIP Support Registers F4BAR2 F4 Index 18h, Base Address Register 2 F4BAR2 points to 2322 Capture Store to Memory VBI DataCapture Store to Memory Video Data Reserved. Read Only Current Field. Read Only Start of each field Offset 14h-17h Bit Description Video Data Capture Active. Read OnlyReserved. Read Only Run Status. Read Only 3110 Reserved Offset 48h-4Bh VBI Data Pitch Register R/W Offset 44h-47h VBI Data Even Base Register R/W Optional Instruction Support Jtag Mode Instruction SupportTestability Jtag Mandatory Instruction Support 366 Absolute Maximum Ratings General SpecificationsPower/Ground Connections and Decoupling Electro Static Discharge ESD Itor to VSS 233 or 266 MHz 300 MHz Symbol Parameter Min Typ Max Unit CommentsOperating Conditions Multipliers 233 or 266 MHz 300 MHz DC Current Power Planes of External Interface SignalsPower Plane Signal Names VCC Balls VSS Balls Power State Parameter Definitions DC Characteristics for On State Symbol ParameterNote Min Typ Max Unit Comments DC Characteristics for Active Idle, Sleep, and Off States Ball Capacitance and Inductance Symbol Parameter Min Typ Max Unit Comment External PU or PD resistor Pull-Up and Pull-Down ResistorsBalls with PU/PD Resistors VIO 10. Buffer Types DC CharacteristicsSymbol Description Reference Wire Inbtn DC Characteristics Inab DC CharacteristicsInpci DC Characteristics INTS1 DC Characteristics Instrp DC CharacteristicsINT DC Characteristics Ints DC Characteristics ODn DC Characteristics Inusb DC Characteristics Ousb DC Characteristics Odpci DC CharacteristicsN DC Characteristics Opci DC Characteristics CLK AC Characteristics11. Default Levels for Measurement Switching Parameters Symbol Parameter Value Outputs Memory Controller InterfaceInputs 12.5 12. Memory Controller Timing ParametersSDCLK30, Sdclkout high time 233 MHz 266 MHz 300 MHz 13.5 MD630 Data Valid Read Data T1, t2, t3SDCLK30 Control Output, MA120 BA10, MD630 Vpckin Vref Video Port 13. Video Input Port Timing Parameters 14. TFT Timing Parameters CRT and TFT Interface 15. CRT Vesa Compatible DAC RED, GREEN, and Blue Outputs Symbol Parameter Note Min Max Unit Comments 17. ACCESS.bus Output Timing Parameters 16. ACCESS.bus Input Timing Parameters AB1D AB2D AB1CAB1C AB2C AB1D AB2D AB1C AB1D AB2D AB1C AB2C390 PCI Bus Interface 18. PCI AC Specifications 64VIO 16VIOEquation a Equation B Pciclk 0.4 V IO 19. PCI Clock Parameters 20. PCI Timing Parameters 21. Measurement Condition Parameters Symbol Value Unit CommentsMeasurement and Test Conditions Ms typ PowerSignals Input Valid Bus Width Min Symbol Parameter Bits Type CommentsSub-ISA Interface 22. Sub-ISA Timing Parameters DOCR#/IOR# Bus Width Min Max Symbol Parameter Bits Type Comments IOW#/WR# MEMW#/DOCW# ROMCS#/DOCCS#IOR#/RD#/TRDE# MEMR#/DOCR# D150 DOCCS#/ROMCS#IOCS10# IOW#/WR# MEMW#/DOCW# TRDE# LPC Interface 23. LPC and Serirq Timing Parameters IDERST# pulse width IDE signals fall time from 0.9V IO to 0.1V IO = 40 pFIDE signals rise time from 0.1V IO to 0.9V IO = 40 pF IDE Interface 24. IDE General Timing Parameters Width 8-bit min Mode Symbol Parameter Unit Comments25. IDE Register Transfer to/from Device Timing Parameters Cycle time min IDEIORDY0 2,3 Addr valid1IDEIOR0# IDEIOW0# Write IDEDATA70 Read IDEDATA70 165 125 100 26. IDE PIO Data Transfer to/from Device Timing ParametersAMD Geode SC2200 Processor Data Book 405 Read IDEDATA150 IDEIOR0# IDEIOW0# Write IDEDATA150406 27. IDE Multiword DMA Data Transfer Timing Parameters IDEDREQ0 IDEDACK0# IDEIOR0# IDEIOW0# IDECS10#408 28. IDE UltraDMA Data Burst Timing Parameters Mode Symbol Parameter Min Max Unit CommentsAMD Geode SC2200 Processor Data Book 409 IDEIRDY0 DSTROBE0 IDEREQ0STOP0 IDEIOR0# HDMARDY0# AMD Geode SC2200 Processor Data Book 411 IDEIRDY0 DSTROBE0 at deviceIDEDATA150 at device IDEIRDY0 DSTROBE0 at host IDEDATA150 at host 412 IDEDREQ0 device IDEDACK0# hostIDEIOW0#STOP0 host IDEIOR0#HDMARDY0# IDEIOW0# STOP0# IDEDREQ0 deviceAMD Geode SC2200 Processor Data Book 413 IDEADDR20 IDEIOW0# STOP0# host IDEIOR0# HDMARDY0# hostIDEIRDY0 DSTROBE0 device IDEDATA150 device IDECS01# IDEIOR0# HSTROBE0# host DevicetUI IDEDACK0# hostIDEIOW0# STOP0# host IDEIORDY0 DDMARDY0 device IDEDATA150 at device HSTROBE0#At host IDEDATA150 At host IDEIOR0# HSTROBE0# at device AMD Geode SC2200 Processor Data Book 417 IDEDREQ0 device IDEDACK0# host IDEIOW0# STOP0# hostIDEIORDY0# DDMARDY0# IDEIOR0# HSTROBE0# 418 IDEIORDY0# DDMARDY0# deviceIDEDATA150 host IDEADDR20 IDECS01# IDEDACK0# host IDEDATA150 host IDECS01# IDEADDR20 IDEDREQ0 device IDEDACK0 host IDEIOW0# STOP0# hostAMD Geode SC2200 Processor Data Book 419 Low Speed Source Note Full Speed Receiver EOP Width Note Low Speed Receiver EOP Width Note Source EOP widthHost upstream Receiver data jitter tolerance for paired Consecutive Transitions Rise Time Fall TimeDifferential Data Lines Differential Data Lines Crossover Points 2.0 Consecutive Transitio ns Differential Data to SE0 SkewData Crossover Level EOP Width Setting of the Rxhsc bit bit 5 of the Rccfg register Modulation signal periodTCPN + Transmitter Sharp-IR and Consumer Remote Control SIR signal pulse width MIR Fast IR Port 31. Fast IR Port Timing ParametersFIR STB# Busy ACK# 33. Enhanced Parallel Port Timing Parameters Symbol Parameter MinUnit Comments Busy 34. ECP Forward Mode Timing ParametersExtended Capabilities Port ECP AFD# BUSY# 35. ECP Reverse Mode Timing Parameters AC97RST# active low pulse width Audio Interface AC97 36. AC Reset Timing ParametersAC97RST# inactive to Bitclk 162.8 Startup delay Sync inactive to Bitclk startup 162.8 Delay AC97CLK Vold 38. AC97 Clocks Parameters SDATAOUT/SYNC SDATAIN, SDATAIN2 39. AC97 I/O Timing Parameters 40. AC97 Signal Rise and Fall Timing Parameters Bitclk Sdataout 41. AC97 Low Power Mode Timing ParametersEnd of Slot 2 to Bitclk Sdatain low Slot ONCTL# PWRBTN# Power ManagementPower management event to ONCTL# Assertion 42. PWRBTN# Timing Parameters PWRBTN# ONTCL# PWRCNT21 POR# AMD Geode SC2200 Processor Data Book 437 POR# 32KHZ TDI, TMS hold time TDI, TMS setup timeNon-test inputs setup time Jtag Interface 46. Jtag Timing Parameters AMD Geode SC2200 Processor Data Book 439 Output SignalsInput Signals TDI TMS TDO 440 ΘJC ×C/W Thermal CharacteristicsCase-to-Ambient Thermal Resistance Example @ 85C Assume P max = 9W and TA max = 40C Therefore Heatsink ConsiderationsExample Assume P max = 5W and TA max = 40C Therefore Package Specifications Physical DimensionsAMD Geode SC2200 Processor Data Book 445 446 BGU481 Package Bottom View Degree C Package2 Order InformationOrdering Part Number Core Frequency MHz Table A-1. Revision History Data Book Revision HistoryRevision # Revisions / Comments