Manuals / Asante Technologies / Computer Equipment / Switch

Asante Technologies 35160 Connecting to the Network, 1 10/100/1000BaseT Ports Cabling Procedures

Models: 35160

1 88

Download 88 pages 15.65 Kb

Page 15

2.6 Connecting to the Network

The switch may be connected to an Ethernet network with the unit powered on or off. Use the following procedure to make the network connections:

1.Connect the network devices to the switch, following the cable guidelines outlined below.

2.After the unit is connected to the network, it can be configured for management capabilities (see the following chapters for information on configuration).

2.6.110/100/1000BaseT Ports Cabling Procedures

The 10/100/1000 ports on the switch allow for the connection of 10BaseT, 100BaseTX, or 1000BaseT network devices. The ports are compatible with IEEE 802.3 and 802.3u standards.

Important: The switch must be located within 100 meters of its attached 10BaseT or 100BaseTX devices.

Use the following guidelines to determine the cabling requirements for the network devices:

•Connecting to Network Station: Category 5 UTP (Unshielded Twisted- Pair) straight-through cable (100 meters maximum) with RJ-45 connectors

•Connecting to Repeater/Hub/Switch’s Uplink port: Category 5, UTP straight-through cable (100 meters maximum) with RJ-45 connectors

Note: These switches have no specific uplink ports. All 10/100 ports on these switches are auto-sensing MDI/MDI-X. This advanced feature means that the

10/100 ports will automatically determine whether the device at the other end of the link is a hub, switch, or workstation, and adjust its signals accordingly.

Although 10/100BaseT requires only pins 1, 2, 3, and 6, Asanté strongly recommends cables with all 8 wires connected as shown in Table 2-2 below.

1000BaseT requires that all four pairs (8 wires) be connected correctly, using Category 5 or better Unshielded Twisted Pair (UTP) cable (to a distance of 100 meters). Table 2-1 shows the correct pairing of all eight wires.

Pin Number	Pair Number & Wire Colors
1	2 White/Orange
2	2 Orange/White
3	3 White/ Green
4	1 Blue/White
5	1 White/Blue
6	3 Green/White
7	4 White/Brown
8	4 Brown/White

Table 2-2 Pin Numbers and Wire Colors

15

Image 15

Asante Technologies 35160 user manual Connecting to the Network, 1 10/100/1000BaseT Ports Cabling Procedures

Contents

IntraCore 35160 Series Quick Start Guide IntraCore 35160 Series Layer 2 Gigabit Switches User’s ManualTable of Contents Page Introduction FeaturesSwitchCore CXE2010 Package ContentsLEDs 2 IC35160-G 1 IC35160-TFront and Back Panel Descriptions Management and ConfigurationConsole Interface Web-Based InterfaceSnmp Management Recommended Installation Tools Hardware Installation and SetupInstallation Overview Safety OverviewCooling and Airflow Installation into an Equipment RackPower Requirements Environmental RequirementsGbic Interfaces Installing a GbicGbic Care and Handling Installing the Optional Emergency Power SupplyConnecting Power Removing a Gbic1 10/100/1000BaseT Ports Cabling Procedures Connecting to the NetworkSetup Gigabit Ethernet Ports Cabling ProceduresConnecting to a Console Connecting Via Telnet Connecting Via the Web BrowserIP Assignment Changing the PasswordSimple Network Management Protocol Snmp Exiting a Submenu ConfigurationAccessing a Submenu LoggingGeneral Information Configuration MenuChanging System Administration Info Administration ConfigurationSystem IP Configuration Port ConfigurationChanging System IP Information Page Enabling or Disabling a Port Advanced Port ConfigurationEnabling or Disabling 802.3x Flow Control Setting Port Class of ServiceSetting Port Default Priority Setting Port Maximum Packet LengthGlobal Port Configuration Unicast Forwarding Database ConfigurationDisplaying the Forwarding Database Searching for a MAC Address Setting the MAC Address Age-Out TimeSecurity Management Vlan ManagementProtocol Configuration Snmp ConfigurationChanging Community Strings Adding or Updating a Trap Receiver Enabling Authentication TrapsDeleting a Trap Receiver Spanning Tree Protocol STP ConfigurationSpanning Tree Port Configuration Setting Port Priority and Path CostEnabling and Disabling STP Trunk Group Configuration QoS Priority Queue Management Defining the Priority ListAssigning Packets to Priority Queues Example User Interface Configuration Setting Console UI Time-out PeriodSetting SSH/Telnet UI Time-out Change Password Adding or Deleting an Access HostEnabling or Disabling SSH and Telnet Access Control System UtilitiesEnabling or Disabling the Web Server Port Mirroring Enabling or Disabling System Port MirroringAdding or Deleting a Monitor Port System Reset Resetting the SwitchSystem Clock System Log Scheduling a System ResetClearing the System Log Bootstrap ConfigurationTftp File Transfers Ping Utility StatisticsAdvanced Management Snmp and Rmon ManagementRmon Management Viewing a List of Duplicated IP Addresses Duplicated IP Detection and TrapEnabling and Disabling Duplicated IP Detection Enabling and Disabling Duplicated IP TrapEnabling and Disabling Station Movement Trap Configuring Port SecurityConfiguring Port Lock and Intruder Lock Configuring Port New Node Detection TrapResetting Security to Defaults Port-based Network Access ControlConfiguring Security Level 2 or Level Setting the Intruder TrapPage Name Description Port Control SettingsSetting Timers Setting Radius Parameters Radius Server IPServer Port Vlan Specifications for the IntraCore 35160 Series Other Vlan Features of the switchVlan Management Creating a Vlan Configuring Static Vlan GroupsAdvanced Static Vlan Configuration Adding and Deleting VLANs from the Port Configuring Vlan Port AttributesSetting the Port Vlan ID Configuring Port Receive Frame TypeDisplaying a Summary of Vlan Groups Setting Port TypeMulticast Addresses Resetting Vlan Configuration to DefaultsIP Multicast Traffic Management Displaying a Vlan Port SummaryConfiguring IP Multicast Traffic Management Igmp SnoopingEnabling and Disabling Igmp Snooping Displaying a Summary of Group Addresses Advanced Igmp ConfigurationRemoving a Multicast Group Address IP Multicast Forwarding Database ConfigurationAdding Ports to the Selected Address Inserting a Multicast Group AddressWeb-Based Management Accessing with a Web BrowserFront Panel Button Genl Info General Information ButtonManagement Buttons Port Config Port Configuration Button Span Tree Spanning Tree Button Addr Address Table Button Snmp ButtonVlan Configuration Vlan ButtonVlan Group Create Acceptable Frame Type Port ConfigurationSet Port Type Port Vlan ID PvidTag/Untag Port Egress Type Trunking ButtonSecurity Button Port Ingress FilteringPage Snmp Management Snmp Management OperationsSnmp Protocol Community Name and Security MIB TreeName Space Path MIB Groups Supported Vlan ID and Tagged Frames Switching ConceptsVLANs Port-Based VLANsSpanning Tree Parameters Spanning Tree ProtocolPort Vlan ID How It WorksSpanning Tree Port Configuration Full Duplex, Flow Control, and Auto-negotiationFull Duplex Auto-Negotiation Flow ControlProblem Possible Solutions Appendix A. TroubleshootingAppendix B. Features and Specifications SpecificationsPhysical Characteristics Technical Support and Warranty Environmental RangeStandards Compliance Appendix C. FCC Compliance and Warranty Statements FCC Compliance Statement Important Safety InstructionsIntraCare Warranty Statement Page Appendix D. Console Port Pin Outs Pin Number Signal NameAppendix E. Online Warranty Registration Loading Software Locally Appendix F. BootP ConfigurationBootstrap Configuration Image BanksLoading Software Remotely BOOTP-TFTP