Manuals / Asante Technologies / Computer Equipment / Switch

Asante Technologies 35160 user manual Loading Software Remotely, Bootp-Tftp

Models: 35160

1 88

Download 88 pages 15.65 Kb

Page 88

Loading Software Remotely

To set the switch to download its software over the network from a remote server, use the following procedure:

1.Open the Local Bootstrap Configuration Menu by typing b in System Utility Menu.

2.Open the Remote Bootstrap Configuration Menu by typing r in the Local Bootstrap Configuration Menu. The menu appears, as shown below.

IntraCore 35160-T Bootstrap Configuration Menu

Bank 1 Image Version/Date: 1.20B/Jun 17 2003 20:41:25 (Running)

Bank 2 Image Version/Date: 1.10 /May 20 2003 18:01:54

Load Mode:	Remote
Boot Mode:	BOOTP-TFTP
Boot Server IP:	N/A
Boot File Name:	N/A
Retry Count:	5
Boot Bank:	1

<Cmd> <Description>

bSet Boot Mode to BOOTP-TFTP

tSet Boot Mode to TFTP only

lSet Load Mode to LOCAL

sSet Boot Server IP Address

fSet Boot File Name

cSet Remote Boot Retry Count

aToggle Boot Bank

oCommence Bootstrap Sequence

qReturn to previous menu

root>

3.Type b to set the Boot Mode to BootP-TFTP, or type t to set Boot Mode to TFTP only. If you choose BootP-TFTP mode, the options for setting the IP Address of the TFTP server and the Boot File Name become unavailable; in this case, skip Steps 4–7 and go on to Step 8.

4.Type s in the Bootstrap Configuration Menu to select the option Set Boot Server IP Address.

5.At the prompt, type the IP address of the remote boot server that contains the switch’s software image file. Then press Enter. The Bootstrap Configuration Menu appears.

6.Type f to select the option Set Boot File Name.

7.Type the software’s file name/network path at the prompt.

8.Press Enter.

Note: If you decide to use Local Load Mode rather than Remote, type I, and the Local Bootstrap Configuration Menu appears.

The switch is now set to download its software remotely from the network. This will occur the next time the unit is powered on or reset.

88

Image 88

Asante Technologies 35160 user manual Loading Software Remotely, Bootp-Tftp

Contents

IntraCore 35160 Series Quick Start Guide Layer 2 Gigabit Switches User’s Manual IntraCore 35160 SeriesTable of Contents Page Features IntroductionPackage Contents SwitchCore CXE2010LEDs 1 IC35160-T 2 IC35160-GManagement and Configuration Front and Back Panel DescriptionsWeb-Based Interface Console InterfaceSnmp Management Hardware Installation and Setup Installation OverviewSafety Overview Recommended Installation ToolsInstallation into an Equipment Rack Power RequirementsEnvironmental Requirements Cooling and AirflowInstalling a Gbic Gbic InterfacesInstalling the Optional Emergency Power Supply Connecting PowerRemoving a Gbic Gbic Care and HandlingConnecting to the Network 1 10/100/1000BaseT Ports Cabling ProceduresGigabit Ethernet Ports Cabling Procedures SetupConnecting to a Console Connecting Via the Web Browser Connecting Via TelnetChanging the Password IP AssignmentSimple Network Management Protocol Snmp Configuration Accessing a SubmenuLogging Exiting a SubmenuConfiguration Menu General InformationAdministration Configuration Changing System Administration InfoPort Configuration System IP ConfigurationChanging System IP Information Page Advanced Port Configuration Enabling or Disabling a PortSetting Port Class of Service Setting Port Default PrioritySetting Port Maximum Packet Length Enabling or Disabling 802.3x Flow ControlUnicast Forwarding Database Configuration Global Port ConfigurationDisplaying the Forwarding Database Setting the MAC Address Age-Out Time Security ManagementVlan Management Searching for a MAC AddressSnmp Configuration Protocol ConfigurationChanging Community Strings Enabling Authentication Traps Adding or Updating a Trap ReceiverSpanning Tree Protocol STP Configuration Deleting a Trap ReceiverSetting Port Priority and Path Cost Spanning Tree Port ConfigurationEnabling and Disabling STP Trunk Group Configuration Defining the Priority List QoS Priority Queue ManagementAssigning Packets to Priority Queues Example Setting Console UI Time-out Period User Interface ConfigurationSetting SSH/Telnet UI Time-out Adding or Deleting an Access Host Change PasswordEnabling or Disabling SSH and Telnet System Utilities Access ControlEnabling or Disabling the Web Server Enabling or Disabling System Port Mirroring Port MirroringAdding or Deleting a Monitor Port Resetting the Switch System ResetSystem Clock Scheduling a System Reset System LogBootstrap Configuration Clearing the System LogTftp File Transfers Statistics Ping UtilitySnmp and Rmon Management Advanced ManagementRmon Management Duplicated IP Detection and Trap Enabling and Disabling Duplicated IP DetectionEnabling and Disabling Duplicated IP Trap Viewing a List of Duplicated IP AddressesConfiguring Port Security Enabling and Disabling Station Movement TrapConfiguring Port New Node Detection Trap Configuring Port Lock and Intruder LockPort-based Network Access Control Configuring Security Level 2 or LevelSetting the Intruder Trap Resetting Security to DefaultsPage Port Control Settings Name DescriptionSetting Timers Radius Server IP Setting Radius ParametersServer Port Other Vlan Features of the switch Vlan Specifications for the IntraCore 35160 SeriesVlan Management Configuring Static Vlan Groups Creating a VlanAdvanced Static Vlan Configuration Configuring Vlan Port Attributes Setting the Port Vlan IDConfiguring Port Receive Frame Type Adding and Deleting VLANs from the PortSetting Port Type Displaying a Summary of Vlan GroupsResetting Vlan Configuration to Defaults IP Multicast Traffic ManagementDisplaying a Vlan Port Summary Multicast AddressesIgmp Snooping Configuring IP Multicast Traffic ManagementEnabling and Disabling Igmp Snooping Advanced Igmp Configuration Displaying a Summary of Group AddressesIP Multicast Forwarding Database Configuration Adding Ports to the Selected AddressInserting a Multicast Group Address Removing a Multicast Group AddressAccessing with a Web Browser Web-Based ManagementGenl Info General Information Button Front Panel ButtonManagement Buttons Port Config Port Configuration Button Span Tree Spanning Tree Button Snmp Button Addr Address Table ButtonVlan Button Vlan ConfigurationVlan Group Create Port Configuration Set Port TypePort Vlan ID Pvid Acceptable Frame TypeTrunking Button Security ButtonPort Ingress Filtering Tag/Untag Port Egress TypePage Snmp Management Operations Snmp ManagementSnmp Protocol MIB Tree Community Name and SecurityName Space Path MIB Groups Supported Switching Concepts VLANsPort-Based VLANs Vlan ID and Tagged FramesSpanning Tree Protocol Port Vlan IDHow It Works Spanning Tree ParametersFull Duplex, Flow Control, and Auto-negotiation Spanning Tree Port ConfigurationFull Duplex Flow Control Auto-NegotiationAppendix A. Troubleshooting Problem Possible SolutionsSpecifications Appendix B. Features and SpecificationsPhysical Characteristics Environmental Range Technical Support and WarrantyStandards Compliance FCC Compliance Statement Important Safety Instructions Appendix C. FCC Compliance and Warranty StatementsIntraCare Warranty Statement Page Pin Number Signal Name Appendix D. Console Port Pin OutsAppendix E. Online Warranty Registration Appendix F. BootP Configuration Bootstrap ConfigurationImage Banks Loading Software LocallyBOOTP-TFTP Loading Software Remotely