General Information, Configuration Menu | Asante Technologies 35160

3.1 General Information

The General Information Screen displays the current system information of the switch, such as its name, IP address, and boot information. The information displayed is read-only.

To view General Information, type g from the Main Menu. A screen similar to that below appears.

IntraCore 35160-T General Information Menu

System up since:			07/16/2003		Wed. 03:57:59pm
Software	Version				1.20B/Jun 17 2003	20:41:25 (Running)
Bank 1	Image	Version/Date:
Bank 2	Image	Version/Date:			1.10 /May 20 2003	18:01:54
System Information					1.01 /Nov 20 2002	10:47:44
PROM Image Version/Date:
DRAM Size:			32.0MB		Flash Size:	4.0MB
Config	NVRAM	Size:		128KB	Console Baud Rate: 9600 bps
Serial	No. :	Information
Administration
System	Name:		<none>
System	Location:		<none>
System	Contact:		<none>
System MAC Address, IP Address, Subnet Mask and Router
MAC Address:			00:00:94:BF:00:46
IP Address:			xxx.xxx.xxx.xxx
Subnet	Mask:		255.255.255.0
Router:			xxx.xxx.xxx.xxx
Bootstrap Configuration
Boot Load Mode:			LOCAL

Press any key to continue...

To exit the General Information Screen, press any key on the keyboard.

3.2 Configuration Menu

The Configuration Menu allows the user to manage and configure the switch and each of its ports. However, you must be logged in with user name root or readwrite in order to make changes to the switch’s configuration. If you are logged in as readonly, you have read-only access, and no configuration options will be available to you.

In the following screen, the user has read-only access, and is checking the bootstrap configuration (System Utilities/Bootstrap Configuration) Menu.

IntraCore 35160-T Bootstrap Configuration Menu

Bank 1 Image Version/Date: 1.20B/Jun 17 2003 20:41:25 (Running)

Bank 2 Image Version/Date: 1.10 /May 20 2003 18:01:54

Load Mode: Local

Boot Bank: 1

<Cmd> <Description>

qReturn to previous menu

readonly>

21

Image 21

Asante Technologies 35160 user manual General Information, Configuration Menu

Contents

IntraCore 35160 Series Quick Start Guide IntraCore 35160 Series Layer 2 Gigabit Switches User’s Manual Table of Contents Page Introduction Features SwitchCore CXE2010 Package ContentsLEDs 2 IC35160-G 1 IC35160-T Front and Back Panel Descriptions Management and Configuration Console Interface Web-Based InterfaceSnmp Management Installation Overview Hardware Installation and SetupSafety Overview Recommended Installation Tools Power Requirements Installation into an Equipment RackEnvironmental Requirements Cooling and Airflow Gbic Interfaces Installing a Gbic Connecting Power Installing the Optional Emergency Power SupplyRemoving a Gbic Gbic Care and Handling 1 10/100/1000BaseT Ports Cabling Procedures Connecting to the Network Setup Gigabit Ethernet Ports Cabling ProceduresConnecting to a Console Connecting Via Telnet Connecting Via the Web Browser IP Assignment Changing the Password Simple Network Management Protocol Snmp Accessing a Submenu ConfigurationLogging Exiting a Submenu General Information Configuration Menu Changing System Administration Info Administration Configuration System IP Configuration Port ConfigurationChanging System IP Information Page Enabling or Disabling a Port Advanced Port Configuration Setting Port Default Priority Setting Port Class of ServiceSetting Port Maximum Packet Length Enabling or Disabling 802.3x Flow Control Global Port Configuration Unicast Forwarding Database Configuration Displaying the Forwarding Database Security Management Setting the MAC Address Age-Out TimeVlan Management Searching for a MAC Address Protocol Configuration Snmp ConfigurationChanging Community Strings Adding or Updating a Trap Receiver Enabling Authentication Traps Deleting a Trap Receiver Spanning Tree Protocol STP Configuration Spanning Tree Port Configuration Setting Port Priority and Path CostEnabling and Disabling STP Trunk Group Configuration QoS Priority Queue Management Defining the Priority ListAssigning Packets to Priority Queues Example User Interface Configuration Setting Console UI Time-out PeriodSetting SSH/Telnet UI Time-out Change Password Adding or Deleting an Access HostEnabling or Disabling SSH and Telnet Access Control System UtilitiesEnabling or Disabling the Web Server Port Mirroring Enabling or Disabling System Port MirroringAdding or Deleting a Monitor Port System Reset Resetting the SwitchSystem Clock System Log Scheduling a System Reset Clearing the System Log Bootstrap Configuration Tftp File Transfers Ping Utility Statistics Advanced Management Snmp and Rmon ManagementRmon Management Enabling and Disabling Duplicated IP Detection Duplicated IP Detection and TrapEnabling and Disabling Duplicated IP Trap Viewing a List of Duplicated IP Addresses Enabling and Disabling Station Movement Trap Configuring Port Security Configuring Port Lock and Intruder Lock Configuring Port New Node Detection Trap Configuring Security Level 2 or Level Port-based Network Access ControlSetting the Intruder Trap Resetting Security to DefaultsPage Name Description Port Control Settings Setting Timers Setting Radius Parameters Radius Server IPServer Port Vlan Specifications for the IntraCore 35160 Series Other Vlan Features of the switchVlan Management Creating a Vlan Configuring Static Vlan Groups Advanced Static Vlan Configuration Setting the Port Vlan ID Configuring Vlan Port AttributesConfiguring Port Receive Frame Type Adding and Deleting VLANs from the Port Displaying a Summary of Vlan Groups Setting Port Type IP Multicast Traffic Management Resetting Vlan Configuration to DefaultsDisplaying a Vlan Port Summary Multicast Addresses Configuring IP Multicast Traffic Management Igmp SnoopingEnabling and Disabling Igmp Snooping Displaying a Summary of Group Addresses Advanced Igmp Configuration Adding Ports to the Selected Address IP Multicast Forwarding Database ConfigurationInserting a Multicast Group Address Removing a Multicast Group Address Web-Based Management Accessing with a Web Browser Front Panel Button Genl Info General Information ButtonManagement Buttons Port Config Port Configuration Button Span Tree Spanning Tree Button Addr Address Table Button Snmp Button Vlan Configuration Vlan ButtonVlan Group Create Set Port Type Port ConfigurationPort Vlan ID Pvid Acceptable Frame Type Security Button Trunking ButtonPort Ingress Filtering Tag/Untag Port Egress TypePage Snmp Management Snmp Management OperationsSnmp Protocol Community Name and Security MIB TreeName Space Path MIB Groups Supported VLANs Switching ConceptsPort-Based VLANs Vlan ID and Tagged Frames Port Vlan ID Spanning Tree ProtocolHow It Works Spanning Tree Parameters Spanning Tree Port Configuration Full Duplex, Flow Control, and Auto-negotiationFull Duplex Auto-Negotiation Flow Control Problem Possible Solutions Appendix A. Troubleshooting Appendix B. Features and Specifications SpecificationsPhysical Characteristics Technical Support and Warranty Environmental RangeStandards Compliance Appendix C. FCC Compliance and Warranty Statements FCC Compliance Statement Important Safety InstructionsIntraCare Warranty Statement Page Appendix D. Console Port Pin Outs Pin Number Signal Name Appendix E. Online Warranty Registration Bootstrap Configuration Appendix F. BootP ConfigurationImage Banks Loading Software Locally Loading Software Remotely BOOTP-TFTP