Figure B-2. E1/T1 Board Location | Black Box MWU2000-V35 instruction

2.048Mbps Wireless Modem

Figure B-2. E1/T1 Board Location

To access the jumpers:

1.Disconnect all cables, including the power cable, from the unit.

2.Loosen and remove the two screws on the rear panel. Carefully slide out the boards. The jumpers are located at the bottom side of the LIU board shown in Figure B-3.

3.Turn the boards over, loosen and remove the three screws connecting the LIU board to the main board.

4.Unscrew and remove the nuts and the spring washers from the Tx and Rx connectors. For easier removal of the LIU board, unscrew the small metal panel holding the LIU connectors.

5.Carefully separate the LIU board from the main board, taking care not to damage the P1 and P2 pins.

6.Set the jumpers according to diagrams B-3 to B-5.

116 SALES: 0118 965 5100

Image 116

Black Box MWU2000-V35, MWU2000-G703, MWU2000-X21 manual Figure B-2. E1/T1 Board Location, To access the jumpers

Contents

0118 965 Basingstoke Road, Reading, Berkshire RG2 0QN 048Mbps Wireless Modem Sales 0118 965 048Mbps Wireless Modem Contents Set-up and Configuration Properly General Introduction About this Manual 2.048Mbps Wireless Modem Product Description Error-Free Data Transfer Seamless CommunicationVersatility High Speed Communication Choice of Antennas, Cables and RF Accessories 048Mbps Wireless Modem Benefits048Mbps Wireless Modem Components Co-location Line Interface Unit RS530 Fractional E1 with Echo Cancellation Fractional T1 With Echo CancellationModem Separate DSP Transmit and Receive Modems Adaptive Equalization Radio Antennas Line Front Panel IndicatorsGeneral TX Sync RXD and TXDRx Sync 048Mbps Wireless Modem Connectors 048Mbps Wireless Modem Connections E1 or Fractional E1 LIU Package Components Installation Antennas and AccessoriesInstalling the 2.048Mbps Wireless Modem General To Configure the Unit as Master To Set the Clock Rate V.35/RS-530/X.21 only To Configure Channels Fractional E1 To Configure Channels with Echo Cancellation- Fractional E1 To Configure Channels with Echo Cancellation- Fractional T1 To Configure Channels- Fractional T1 Antennas, Cables and Accessories Basic Antenna Uni-8.5 Basic 8.5 dBi Antenna Showing Installation screws Medium Gain 12dBi Antenna Uni-12 Medium Gain 12dBi Antenna Medium Gain 18dBi Antenna Uni-18 Medium Gain 18dBi Antenna High Gain Antenna Uni-24 High Gain 24dBi antenna TPA 24 Transmit Power Amplifier RF AccessoriesAntenna Characteristics Installing the TPA TPA 24 Connections Diagram LNA-10 Low Noise Receive Amplifier Achievable improvement through the use of LNA-10 LNA Improvement table LNA-10 Cable Connection Diagram Installing the AL-1 Lightning Arrestor Cable Types Thin CableThick Cable Low Loss Cable Antenna Sets 11. Wall Mount with Azimuth Alignment Only 12. Wall Mount with Azimuth and Elevation Alignment Range Tables European Range Table USA Range Table Antenna Alignment Visually Aligning the antennasActivating the front panel LEDs Maximum Unregulated Range Table 14. Rssi measurement connection diagram To activate the front panel LEDs 15. Rssi test point accuracy 048Mbps Wireless Modem 18. Default position NC of the Jumpers in the Receive Module Synchronizing Co-located Modem Units Installing the Antennas Setting the relevant parameters Maximum Number Synchronized Links Connecting the Master units 21. Connecting Units for Synchronization Set-up and Configuration Set-up and Configuration FunctionsAccessing the Set-up and Configuration Functions Main Menu Counters and Tracers Menu Mode and Access Control MenuParameters Menu System Reset TestingTo access the Parameters Menu To make selections using the Parameters menu E1 Parameters Menu Items and Actions LIU Parameters MenuE1 Parameters Menu E1 Alarm Buffer Fractional EI Parameters Manu Remote Alarm Method Fractional E1 parameters Menu Items and Actions Echo Canceller disabling method Fractional E1 Alarm BufferLong haul/Short haul CRC4 Usage T1 Alarm Buffer T1 Parameters MenuT1 Parameters Menu Items and Actions Pulse Shape Fractional T1 Parameters Menu 048Mbps Wireless Modem 048Mbps Wireless Modem D4 Yellow Alarm Method Superframe Method Echo Canceler CRC6 UsageBit 7 Zero Suppression Pulse Density Enforcer Fractional T1 Alarm buffer DCE/DTE Functionality Options 35/RS530/X.21 Parameter MenuV.35/RS-530/X.21 Parameters Menu Items and Actions Loopback Mode Menu Loopback Mode Menu Items and Actions Clock Polarity Line Interface Unit Type Menu Options MCP Parameters MenuLine Interface Unit Type Menu Master-Slave Total Link DelayMCP Parameters Menu Options Central Site Management Using a Dial-up Modem Modem Initialisation String AT&f\n 11. Default Modem Rate According to Selected LIU Data Rat Radio and Modem Parameters Menu10. Radio and Modem Parameters Menu Options Modem Rate Add/Remove Channels from Test Sequence Remote ParametersHoping Sequence 12. Remote Parameters Menu Options Switch to Remote MonitorSwitch to Local Monitor Load Default Values Menu Ping Remote UnitDownload remote database to remote unit Copy database and download to remote unit 13. Load Default Values Menu options Parameter Info. Screen To access the Counters and Tracers Menu To make selections from the Counters and Tracers Menu 2.048Mbps Wireless Modems Counter display System Counters 14. Buffers Name and Description Channel Tracer Rssi per channel 15. Modem Rate Vs. Buffer Size Channel Tracer Errors Per Channel 16. Rssi Levels Clear System Counters and Channel Tracer Time Tracer Errors versus TimeTime Tracer Max Consecutive Errors versus Time ⇒ To set the time intervals Set Time Tracer Resolution17. Delay Setting Reset Counters Clear Reset Counter Watch Alarms MessageDescription Correction Remote Frame Alarm Radio Alarms Message Rlos framer un-synchronized General Alarms Message Warning LIU Clock drift, Check clock configuration Message Warning Difference in parameters between two units Change Access Rights Site Survey Mode System Reset Menu Menu Troubleshooting Introduction Problem 2 Poor performance of radio link ⇒ To check the configuration of each unit⇒ To check RF Installation ⇒ To check radio link performance To check synchronization at radio level To correct the configuration⇒ To check each unit configuration From the Parameters menu, select Parameters Info. Screen 048Mbps Wireless Modem To improve data rate To view isolated bursts of errorsTo reduce echo on voice channels Problem 7 The system resets with an error message 048Mbps Wireless Modem Error Messages Source If the telephones does not work properly If Faxes does not work properly 048Mbps Wireless Modem Technical Specifications Wireless Modem Technical Specifications ModelsRadio Type Transmission Technique Default Modem Rate According to Selected LIU Data Rate Transmitter Output PowerChannel Bandwidth System Bandwidth Receiver Sensitivity as a Function of the Radio BER Maximum Spurious LevelReceiver Sensitivity Adjacent Channel Rejection Maximum Receive LevelRecommended Receive Level Adjacent Channel Rejection Separate between TX and RX frequencies Filter Curves Maximum Number of Links to SynchronizeMaximum Number of Synchronized Links Line Interface Specifications 101 Fractional T1 Interface Fractional E1 InterfaceInterface RS-530 Interface 103 Front Panel LED IndicatorsConnectors Standards Mechanical SpecificationsEnvironmental Specifications TPA 24 Technical Specifications LNA-10 Technical Specifications105 Antennas Sets AL-1 Technical Specifications 106 107 DCE/DTE Configuration Configuration OptionsTable A-1. Possible DTE/DCE Configurations Appendix a V.35/RS-530/X.21 Applications 048Mbps Wireless Modem Standard Configuration Table A-2. Configuration109 Synchronizing your Modem to Another Network Connecting your 2.048Mbps Wireless Modem to another modem RS-530/V.35/X.21 Back-to-Back Configuration 111 DCE Options DTE Options Setting the DCE/DTE Mode ParameterTo set the DCE/DTE mode 113 E1/T1 Connections and Common Problems Link Setup Appendix B E1 / T1 Applications Table B- 1. E1/T1 Connections E1/T1 LIU Jumper Settings115 To access the jumpers Figure B-2. E1/T1 Board Location Figure B-3. E1 Unbalanced Coax connector, 75 W 117 T1 CSU/DSU Applications Figure B-6. T1/DSU Network Interface E1/T1 Back-to-Back Configuration 119 When to Use the Fractional E1/T1 LIU Appendix C Fractional E1/T1 Applications Table C-1. Channels Characteristic 121 Fractional E1 LIU Jumper Settings Table C-2. Fractional E1/T1 Connections 123 Figure C-2. Fractional E1 Board Location Figure C-3. Fractional E1 Unbalanced Coax connector, 75 W 125 Fractional T1 CSU/DSU Applications Fractional E1/T1 Back-to-Back Configuration Echo Cancellation in Fractional E1/T1 Applications Potential Problems in Fractional E1/T1 Applications 127 Appendix D Installing Other Types of Receive Amplifiers To separate DC input 129 To supply DC input through the RF cable LIU RS-530 Connector Pin Assignments Appendix E Pin AssignmentsE1/T1 and Fractional E1/T1 Pin Connections Table E-1. E1/T1 and Fractional E1/T1 Pin Connections 131 LIU D-25 to V.35 Cable Pin Assignments LIU D-25 to X.21 Cable Pin Assignments Figure E-3. LIU D-25 to X.21 Cable Pin Assignments