Carrier 30RAP010-060 specifications Xxx.X Δf

Table 10 — Configuration Mode and Sub-Mode Directory (cont)

SUB-MODE	KEYPAD		ITEM	DISPLAY	ITEM		COMMENT
	ENTRY				EXPANSION
RSET					RESET COOL TEMP
			CRST	X	COOLING RESET TYPE	Default: No Reset
		ENTER
						0 = No Reset
						1 = 4 to 20 mA Input
						2 = Outdoor Air Temperature
						3 = Return Fluid
						4 = Space Temperature
			MA.DG	XX.X ΔF	4-20 - DEGREES RESET	Default: 0.0 ΔF
						Range: –30 to 30 ΔF
			RM.NO	XXX.X °F	REMOTE - NO RESET TEMP	Default: 125 F (51.7 C)
						Range: 0° to 125 F
			RM.F	XXX.X °F	REMOTE - FULL RESET TEMP	Default: 0.0° F (-17.8 C)
						Range:	0° to 125 F
			RM.DG	XX.X °F	REMOTE - DEGREES RESET	Default: 0.0° F
						Range: –30 to 30 F
			RT.NO	XXX.X ΔF	RETURN - NO RESET TEMP	Default: 10.0 ΔF (5.6 ΔC)
						Range:	0° to 125 F COOLER ΔT
			RT.F	XXX.X ΔF	RETURN - FULL RESET TEMP	Default: 0.0 ΔF (0.0 ΔC)
						Range:	0° to 125 F COOLER ΔT
			RT.DG	XX.X °F	RETURN - DEGREES RESET	Default: 0.0° F
						Range: –30 to 30 F (–34.4 to -1.1 C)
			DMDC	X	DEMAND LIMIT SELECT	Default: None
						0 = None
						1 = Switch
						2 = 4 to 20 mA Input
						3 = CCN Loadshed
			DM20	XXX %	DEMAND LIMIT AT 20 MA	Default:	100%
						Range:	0 to 100%
			SHNM	XXX	LOADSHED GROUP NUMBER	Default:	0
						Range:	0 to 99
			SHDL	XXX %	LOADSHED DEMAND DELTA	Default:	0%
						Range:	0 to 60%
			SHTM	XXX	MAXIMUM LOADSHED TIME	Default:	60 minutes
						Range:	0 to 120 minutes
			DLS1	XXX %	DEMAND LIMIT SWITCH 1	Default:	80%
						Range:	0 to 100%
			DLS2	XXX %	DEMAND LIMIT SWITCH 2	Default:	50%
						Range:	0 to 100%
			LLEN	ENBL/DSBL	LEAD/LAG CHILLER ENABLE	Default: Disable
			MSSL	SLVE/MAST	MASTER/SLAVE SELECT	Default: Master
			SLVA	XXX	SLAVE ADDRESS	Default:	0
						Range:	0 to 239
		ENTER				Default: Master Leads
			LLBL	X	LEAD/LAG BALANCE SELECT	0 = Master Leads
						1 = Slave Leads
						2 = Automatic
			LLBD	XXX	LEAD/LAG BALANCE DELTA	Default:	168 hours
						Range:	40 to 400 hours
			LLDY	XXX	LAG START DELAY	Default:	5 minutes
						Range:	0 to 30 minutes
			PARA	YES	PARALLEL CONFIGURATION	Default: YES (CANNOT BE CHANGED)
SLCT					SETPOINT AND RAMP LOAD
			CLSP	X	COOLING SETPOINT SELECT	Default: Single
		ENTER
						0 = Single
						1 = Dual Switch
						2 = Dual CCN Occupied
						3 = 4 to 20 mA Input (requires
						EMM)
			RL.S	ENBL/DSBL	RAMP LOAD SELECT	Default: Enable
			CRMP	X.X	COOLING RAMP LOADING	Default:	1.0
						Range:	0.2 to 2.0
			SCHD	XX	SCHEDULE NUMBER	Default:	1
						Range:	1 to 99
			Z.GN	X.X	DEADBAND MULTIPLIER	Default:	1.0
						Range:	1.0 to 4.0
SERV					SERVICE CONFIGURATION
			EN.A1	ENBL/DSBL	ENABLE COMPRESSOR A1	Unit dependent
		ENTER
			EN.A2	ENBL/DSBL	ENABLE COMPRESSOR A2	Unit dependent
			EN.B1	ENBL/DSBL	ENABLE COMPRESSOR B1	Unit dependent
			EN.B2	ENBL/DSBL	ENABLE COMPRESSOR B2	Unit dependent

15