Manuals / Carrier / Household Appliance / Air Conditioner

Carrier 30RAP010-060 specifications 4 to 20-mADemand Limiting, Cooling Set Point 4 to 20 mA

Models: 30RAP010-060

1 124

Download 124 pages 40.33 Kb

Page 43

Fig. 21 — 4 to 20-mA Demand Limiting

DEMAND LIMIT (CCN Loadshed Controlled) — To con- figure Demand Limit for CCN Loadshed control set the De- mand Limit Select (Configuration→RSET→DMDC) to 3. Then configure the Loadshed Group Number (Configura- tion→RSET→SHNM), Loadshed Demand Delta (Configu- ration→RSET→SHDL), and Maximum Loadshed Time (Configuration→RSET→SHTM). See Table 27.

The Loadshed Group number is established by the CCN system designer. The ComfortLink controls will respond to a Redline command from the Loadshed control. When the Redline command is received, the current stage of capacity is set to the maximum stages available. Should the loadshed con- trol send a Loadshed command, the ComfortLink controls will reduce the current stages by the value entered for Loadshed Demand delta. The Maximum Loadshed Time is the maximum

length of time that a loadshed condition is allowed to exist. The control will disable the Redline/Loadshed command if no Cancel command has been received within the configured maximum loadshed time limit.

Cooling Set Point (4 to 20 mA) — A field supplied and generated, externally powered 4 to 20 mA signal can be used to provide the leaving fluid temperature set point. Connect the signal to LVT7,8 (+,–). See Table 27 for instructions to enable the function. Figure 22 shows how the 4 to 20 mA sig- nal is linearly calculated on an overall 10 F to 80 F range for fluid types (Configuration→OPT1→FLUD) 1 or 2. The set point will be limited by the fluid (FLUD) type. Be sure that the chilled water loop is protected at the lowest temperature.

	100									50% CAPACITY AT 20 mA
										50% CAPACITY AT 20 mA
(%)
LOAD	80
LOAD
ALLOWABLE.MAX	60
	40	100% CAPACITY AT 4 mA				75% CAPACITY AT 12 mA
						75% CAPACITY AT 12 mA
	20
	0	0	2	4	6	8	10	12	14	16	18	20
						DEMAND LIMIT SIGNAL – 4 - 20 mA INPUT

Fig. 21 — 4 to 20-mA Demand Limiting

	100
	(38)
	90
	(32)
	80
	(27)
	70
	(21)						MAXIMUM
							SET POINT
	60						70 F (21.1 C)
F (C)	(15)
F (C)	50
POINT,	50
	(10)
	40
SET	40
	(4.4)
				(FLUD = 1) MINIMUM
				(FLUD = 1) MINIMUM
	30			SET POINT 38 F (3.3 C)
	(-1)
	20
	(-7)
	10	(FLUD = 2) MINIMUM
	10	SET POINT 14 F (-10 C)
	(-12)
	0
	(-17)
	4	6.3	8.6	10.9	13.1	15.4	17.7	20

4 TO 20 mA SIGNAL TO EMM

EMM — Energy Management Module

Fig. 22 — Cooling Set Point (4 to 20 mA)

43

Image 43

Carrier 30RAP010-060 specifications 4 to 20-mADemand Limiting, Cooling Set Point 4 to 20 mA

Contents

Microchannel Heat Exchanger MCHX CONTENTSCondenser Coil Maintenance and Cleaning Operation of Machine Based on Control MethodAPPENDIX E — MAINTENANCE SUMMARY CONTENTS contSAFETY CONSIDERATIONS APPENDIX C — FACTORY SETTINGS FORFig. 1 — Scrolling Marquee Display GENERALBasic Controls Usage Table 1 — Unit SizesFig. 2 — Accessory Navigator Display Module MODE Table 3 — Run Status Mode and Sub-ModeDirectory SUB-MODE Table 4 — Service Test Mode and Sub-ModeDirectory Table 6 — Pressure Mode and Sub-ModeDirectory Table 5 — Temperature Mode and Sub-ModeDirectoryTable 7 — Set Points Mode and Sub-ModeDirectory KEYPAD Table 8 — Inputs Mode and Sub-ModeDirectoryTable 9 — Outputs Mode and Sub-ModeDirectory SUB-MODETable 9 — Outputs Mode and Sub-ModeDirectory cont OPT1 DISPLAY SUB-MODEKEYPAD ITEMDISPLAY SUB-MODEKEYPAD ITEMDefault: No Reset Repeats for Occupancy Periods 2 through Table 11 — Time Clock Mode and Sub-ModeDirectoryTable 13 — Alarms Mode and Sub-ModeDirectory Table 12 — Operating Mode and Sub-ModeDirectory→PM.DY Table 14 — Operating ModesControl Module Communication CONTROLSCarrier Comfort Network CCN Interface — Table 17 — Output Relays Table 18 — CCN Communication Bus WiringTable 15 — Thermistor Designations Table 16 — Status InputsLEGEND FOR FIG. a30-4963 a30-4962Fig. 3 — Typical Control Box for 30RAP010,015 Fig. 4 — Typical Control Box for 30RAP018-030Fig. 5 — Typical Control Box for 30RAP035-060 a30-4964~ H1 FIOP/ACCESSORYGFI-CO J3 J4 a30-4966SEE NOTES ON PAGEFIOP/ACCESSORY 5283GFI-CO J2 CH1 a30-5284J3 J4 J9 J7a30-4968 Fig. 10 — Typical Space Temperature Sensor WiringFig. 8 — Main Base Board a30-4967•4 to 20 mA leaving fluid temperature reset requires field-supplied4 to 20 mA generator CEPL130351 Fig. 12 — Energy Management ModuleFig. 13 — Deadband Multiplier a30-4969 Operation of Machine Based on ControlFig. 14 — Operating Envelope for R-410ACompressor Table 20 — Fan Stages Cooling Set Point Selecta30-4970 Fig. 15 — 30RAP Condenser Fan LayoutOptional Factory-InstalledHydronic Pack →PM1E = YES →PM1E = YES→PM2E = YES →PM1E = YESConfiguring and Operating Dual Chiller Con SUB-MODE Fig. 17 — Dual Leaving Water Thermistor Well Fig. 16 — Dual Chiller Thermistor LocationCTRL Table 24 — 4 to 20 mA Reset Table 26B — Configuring Return Temperature Reset Fig. 20 — Standard Chilled Fluid Fig. 18 — Outdoor-AirTemperature ResetFig. 19 — Space Temperature Reset Temperature Control — No ResetFig. 22 — Cooling Set Point 4 to 20 mA Fig. 21 — 4 to 20-mADemand LimitingPRE-START-UP Table 27 — Configuring Demand LimitSystem Check →CTPT START-UPAND OPERATIONa30-4978 Fig. 23 — Sight Glass LocationStandard 30RAP Units Table 29 — Temperature Limits forOperating Limitations OPERATION SEQUENCEElectronic Components SERVICETable 30 — EXV Steps Fig. 24 — Electronic Expansion Valve Details a30-4971a30-4972 Compressor Replacement Refer to Fig.Table 31 — Unit Torque Specification CoolerCheck Refrigerant Feed Components Oil ChargeFig. 27 — Compressor Location — 30RAP035-060 Fig. 26 — Compressor Location — 30RAP010-030a30-4973 a30-4974Switch Fixed Table 32 — Factory Settings, High-PressureCheck Unit Safeties Fig. 28 — Thermistor Well Voltage Drop for EWT, LWT, RGT, and OAT Voltage Drop for EWT, LWT, RGT, and OAT For SPT For SPT Table 37 — 86K Thermistor vs Resistance DTTFig. 29 — Thermistor Connections to Main Base Board, J8 ConnectorFig. 30 — Chilled Water Flow Switch a30-4975•P51: SOFTWARE version •P50: FAULT HISTORY — Last 8 faultsMode Fig. 32 — Typical Motormaster Wiringa30-4977 CONFIGURATION TABLEDESCRIPTION Table 38 — Fault CodesFAULT CODE SOLUTIONPARAMETERS Table 40 — Replacement Modules MAINTENANCETROUBLESHOOTING Time Fig. 34 — Advanced Scroll TemperatureProtection Label MinutesTable 41 — Troubleshooting Table 42 — Alarm and Alert Codes Table 42 — Alarm and Alert Codes cont ALARM Table 42 — Alarm and Alert Codes contALARM Table 42 — Alarm and Alert Codes contCOMPRESSOR FAILURE ALERTS Table 42 — Alarm and Alert Codes contCOMPRESSOR STUCK ON FAILURE ALARMS T133 Circuit A Low Suction Pressure APPENDIX A — DISPLAY TABLES Run Status Mode and Sub-ModeDirectoryAPPENDIX A — DISPLAY TABLES cont Run Status Mode and Sub-ModeDirectory contAPPENDIX A — DISPLAY TABLES cont Service Test Mode and Sub-ModeDirectoryTemperature Mode and Sub-ModeDirectory Pressures Mode and Sub-ModeDirectoryInputs Mode and Sub-ModeDirectory Set Points Mode and Sub-ModeDirectoryAPPENDIX A — DISPLAY TABLES cont APPENDIX A — DISPLAY TABLES cont Outputs Mode and Sub-ModeDirectoryITEM Configuration Mode and Sub-ModeDirectoryAPPENDIX A — DISPLAY TABLES cont SUB-MODEITEM Configuration Mode and Sub-ModeDirectory contAPPENDIX A — DISPLAY TABLES cont SUB-MODECIR A EXV CONFIGURATION Configuration Mode and Sub-ModeDirectory contAPPENDIX A — DISPLAY TABLES cont ITEM Configuration Mode and Sub-ModeDirectory contAPPENDIX A — DISPLAY TABLES cont SUB-MODEITEM Configuration Mode and Sub-ModeDirectory contAPPENDIX A — DISPLAY TABLES cont SUB-MODEAPPENDIX A — DISPLAY TABLES cont Time Clock Mode and Sub-ModeDirectoryAPPENDIX A — DISPLAY TABLES cont Time Clock Mode and Sub-ModeDirectory contAPPENDIX A — DISPLAY TABLES cont Time Clock Mode and Sub-ModeDirectory contSUB-MODE APPENDIX A — DISPLAY TABLES cont Time Clock Mode and Sub-ModeDirectory contSUB-MODE ITEM Time Clock Mode and Sub-ModeDirectory contAPPENDIX A — DISPLAY TABLES cont SUB-MODEAlarms Mode and Sub-ModeDirectory Operating Mode and Sub-ModeDirectoryAPPENDIX A — DISPLAY TABLES cont APPENDIX B — CCN TABLES APPENDIX B — CCN TABLES cont APPENDIX B — CCN TABLES cont CCN DISPLAY TABLES — OPTIONS Unit ParametersControl Method APPENDIX B — CCN TABLES contLEAD/LAG APPENDIX B — CCN TABLES contAPPENDIX B — CCN TABLES cont CCN SERVICE TABLES — SERVICECCN MAINTENANCE TABLES — CIRA_EXV CCN SETPOINT TABLES — SETPOINTAPPENDIX B — CCN TABLES cont CCN MAINTENANCE TABLES — CIRB_EXVCCN MAINTENANCE TABLES — STRTHOUR CCN MAINTENANCE TABLES — CURRMODSAPPENDIX B — CCN TABLES cont CCN MAINTENANCE TABLES — ALARMSCCN MAINTENANCE TABLES — VERSIONS CCN MAINTENANCE TABLES — LOADFACTCCN MAINTENANCE TABLES — TESTMODE CCN MAINTENANCE TABLES — PM-PUMPCCN MAINTENANCE TABLES — PM-STRN CCN MAINTENANCE TABLES — PM-COILAPPENDIX B — CCN TABLES cont CCN MAINTENANCE TABLES — RUNTESTAPPENDIX B — CCN TABLES cont CCN MAINTENANCE TABLES — DUALCHILUNIT VOLTAGE SETTINGPUMP OPTION PUMP SIZEFig. B — Address Rotary Switches Optional BACnet Communications Wiring —Fig. A — UPC Open Controller Table B — Baud Selection Table Table A — SW3 Protocol Switch Settings for MS/TPFig. C — DIP Switches Fig. D — Network WiringTable C — MS/TP Wiring Recommendations Fig. E — BT485 Terminator InstallationFig. F — BACview6 Device Connection Table E — LED Status Indicators Table G — Network Points List Table G — Network Points List cont POINT DESCRIPTION Table G — Network Points List cont30RAP Maintenance Interval Requirements APPENDIX E — MAINTENANCE SUMMARY AND LOG SHEETSOIL LEVEL 30RAP Weekly Maintenance LogCHECK ALARMS FAULTS DATE30RAP Monthly Maintenance Log 30RAP Seasonal Shutdown Log Form 30RAP-2T Copyright 2010 Carrier CorporationCatalog No. Printed in U.S.ADesign Information START-UPCHECKLIST FOR 30RAP LIQUID CHILLERRemove and use for Job File I.Project Information II. Preliminary Equipment CheckStart and Operate Machine. Complete the Following III. Unit Start-UpCL-3 CL-4 Record Software Versions MODE — RUN STATUSOPTIONS1 Options Configuration UNIT Configuration SettingsIII.Unit Start-Upcont HP.B Head Pressure Cmp. Delta Configuration OPTIONS2 Options ConfigurationCCN CCN Network Configuration HP.A Head Pressure Cmp. Delta ConfigurationIII. Unit Start-Upcont EXV.A Circuit A EXV ConfigurationEXV.B Circuit B EXV Configuration MM Motormaster Configuration SettingsCL-8 RSET Reset Configuration SettingsSLCT Setpoint and Ramp Load Configuration III.Unit Start-UpcontIII.Unit Start-Upcont SETPOINTCL-9 III.Unit Start-Upcont Service Test Mode and Sub-ModeDirectoryCOMPONENT TEST