System Board Jumper, 125 | Dell T110 manual

Jumpers and Connectors

System Board Jumper

For information on resetting the password jumper to disable a password, see "Disabling a Forgotten Password" on page 128.

Table 6-1. System Board Jumper Settings

Jumper	Setting						Description

PWRD_EN						(default)	The password feature is enabled (pins 2-4)
PWRD_EN						(default)	The password feature is enabled (pins 2-4)
							The password feature is disabled (pins 4-6)


NVRAM_CLR						(default)	The configuration settings are retained at system


							boot (pins 3-5)
							boot (pins 3-5)
							The configuration settings are cleared at the next
							The configuration settings are cleared at the next
							system boot (pins 1-3)
							system boot (pins 1-3)

Jumpers and Connectors

125

Image 125

Dell T110 owner manual System Board Jumper, 125

Contents

Dell PowerEdge T110 Systems August Contents Uefi Boot Settings Screen Processor Settings ScreenEntering the Uefi Boot Manager Using the Uefi Boot Manager Opening and Closing the System Entering the BMC Setup Module Removing the Cooling Shroud Installing the Cooling Shroud Hard Drive Installation GuidelinesRemoving a Hard Drive from a General Memory Module Removing the Power Supply Installing the Power Supply Replacing the System BatteryRemoving the Cooling Fan 101 System Diagnostics Testing Options 122 Contents Troubleshooting a Serial I/O Device 107121 122 Disabling a Forgotten Password Jumpers and Connectors Contents Accessing System Features During Startup Front-Panel Features and Indicators Amber when a system fault is detected Switch Voltage that most closely matches Back-Panel Features and Indicators Guidelines for Connecting External Devices NIC Indicator Codes Link indicator NIC Indicator Codes Power Selection Switch Power Selection Diagnostic Lights System. If the problem persists Configuration error Other failureResource and/or system Board hardware failure Hard drives are properly System Messages Configuration. If the system System configuration If any system componentsBy the power supply Boots without this warning Supported with this power Setting. Cmos has been Installed in the clearSystem Setup Program If not an intentional setting Faulty keyboard controller See Getting Help on Troubleshooting a USBKeyboard cable connector Problem persists, see System Bios Power down and restartSetup program to enable System Setup Program on Lower for power Memory frequency If not an intentional settingFrequency Memory Module Installation Guidelines on Configuration. a Or hard drive. If the problem Faulty or missing opticalSetting the order of boot No boot sector on Incorrect configuration Troubleshooting Expansion Error encountered Install the NvramclrConfiguration Drive connected to Replace the faulty drive Device or medium Device. Ensure that the USB General system error See Getting Help onDevice on page 106 or Removed or a memory Removed, this message is Faulty battery or faulty See Troubleshooting Configuration.Settings faulty system Settings. See Using Number of data lanes Command has been TPM configurationReboot and execute Command Command has been To Ignore or entered. User interaction is Specified slots Memory Module Installation Configuration. MemoryFatal system error System to reboot Will run but with reduced Configuration. See General By the power supplies Boots without this warningFunctionality Memory Module Installation Troubleshooting System Other Information You May Need Diagnostics MessagesAlert Messages About Your System Choosing the System Boot Mode Using the System Setup Program and Uefi Boot Manager Responding to Error Messages Entering the System Setup ProgramUsing the System Setup Program Navigation Keys System if any changes were made Main Screen System Setup Options Memory Settings Screen on Option Description Memory SettingsSata Settings Boot Settings Processor Settings Screen Memory Settings Screen Sata Settings Screen Boot Settings Screen Integrated Devices Screen Boot Sequence RetryManually set the emulation type to Floppy With PXE Serial Communication Screen PCI IRQ Assignments Screen Power Management Screen System Security Screen When set to Yes, all TPM contents are cleared TPM Clear No defaultPower Button When Disabled, the button can only turn on system Using the Uefi Boot Manager Navigation Keys Entering the Uefi Boot ManagerUefi Boot Manager enables you to To enter the Uefi Boot Manager Uefi Boot Settings Screen Uefi Boot Manager Screen System Utilities Screen System and Setup Password FeaturesUsing the System Password Verify that Password Status is Unlocked To disable the password security Using the Setup Password Embedded System Management Deleting or Changing an Existing Setup Password Entering the BMC Setup Module Baseboard Management Controller Configuration Wrist grounding strap Installing System ComponentsRecommended Tools Inside the System Opening the System Opening and Closing the System Opening and Closing the System Release tab Closing the System Removing the Front Bezel Front Bezel Removing Front Bezel Insert Installing the Front Bezel EMI Filler Panel Installing Front Bezel InsertRemoving an EMI Filler Panel Tab EMI filler panel Tab Installing an EMI Filler Panel Removing an Optical or Tape Drive Optical and Tape Drives Optional Tape drive shoulder screws Drive bay screw slots Optical drive Installing an Optical or Tape Drive Installing Drive Shoulder Screws Shoulder screws Removing a Hard Drive Hard Drive Installation GuidelinesHard Drives Tabs Removing or Installing a Hard Drive Hard drive Installing a Hard Drive SAS controller card Removing a Hard Drive from a Hard-Drive Bracket Removing the Expansion Card Stabilizer Installing the Expansion Card StabilizerExpansion Card Stabilizer Removing the Cooling Shroud Cooling Shroud Installing the Cooling Shroud Expansion Cards Expansion Card Installation Guidelines See -1 for the location of the expansion card slots Removing an Expansion Card Installing System Components Expansion-card latch Release tab Expansion-card slots Installing an Expansion Card SAS Controller Expansion Card Mode-Specific Guidelines General Memory Module Installation GuidelinesSystem Memory Sample Udimm Memory Configurations Removing Memory Modules Alignment key Installing Memory Modules Installing System Components Removing the Processor Processor 15. Installing and Removing the Heat Sink Heat sink ZIF socket Installing a Processor Your system has one cooling fan Cooling FanRemoving the Cooling Fan 17. Removing and Installing the Cooling Fan Release tab Installing the Cooling Fan Replacing the System Battery System Battery System battery 18. Replacing the System Battery Removing the Power Supply Power Supply 19. Removing the Power Supply Power supply Screws Cable clip Installing the Power Supply Internal USB Memory Key Removing the Chassis Intrusion Switch Chassis Intrusion Switch Intrusion connector Installing the Chassis Intrusion Switch Removing the Control Panel Assembly Control Panel Assembly 22. Removing the Link Bracket Lock Link bracket lock Control panel cable Standoff Installing the Control Panel Assembly100 101 System BoardRemoving the System Board 102 Installing the System Board 103 104 105 Troubleshooting External ConnectionsTroubleshooting Your System 106 Troubleshooting the Video SubsystemTroubleshooting a USB Device 107 Troubleshooting a Serial I/O DeviceTroubleshooting a NIC 108 Troubleshooting a Wet System 109 Troubleshooting a Damaged System 110 Troubleshooting the System Battery Troubleshooting System Cooling Problems Troubleshooting Power SupplyEnsure that none of the following conditions exist 111 112 Troubleshooting Cooling Fan 113 Troubleshooting System Memory 114 Troubleshooting an Internal USB Key 115 Troubleshooting an Optical Drive 116 Troubleshooting a Tape Backup Unit 117 Troubleshooting a Hard Drive 118 Troubleshooting Expansion Cards 119 Troubleshooting the Processor 120 Embedded System Diagnostics Features Using Online DiagnosticsRunning the System Diagnostics 121 Running the Embedded System Diagnostics When to Use the Embedded System DiagnosticsSystem Diagnostics Testing Options Click the testing option in the Main Menu window Selecting Devices for Testing Using the Custom Test OptionsSelecting Diagnostics Options 123 124 Viewing Information and Results 125 System Board Jumper Sataf eSATA ESATA connector System Board Jumpers and Connectors DescriptionVideo connector 126 127 128 Disabling a Forgotten Password Getting Help Contacting Dell129 130 Glossary 131Amperes AC Alternating current CPU Central processing unit. See processor DC Direct current 132 133 134 Mm Millimeters Ms Milliseconds 135 System 136 System memory See RAM 137TCP/IP Transmission Control Protocol/Internet Protocol TOE TCP/IP offload engine Glossary 138 139 When to useDVD drive. See CD/DVD drive Index 141 Post Panel, 100 power supply, 94 system battery, 91 system board 143 System utilities screen, 49 Uefi Boot Settings screen 144