Part No. 91000051, Revision B | Dynex specification

Part No. 91000051, Revision B

This manual is published by DYNEX Technologies, Inc.

Questions or comments regarding the content of this manual can be directed to the address below or to your DYNEX Technologies representative.

DYNEX Technologies

14340 Sullyfield Circle

Chantilly, VA 20151-1683 USA

Tel. (703) 631-7800

(800)288-2354 Fax. (703) 803-1441

OPSYS MWTM is a trademark of DYNEX Technologies, Inc.

♥2006 This document is the copyright of DYNEX Technologies and must not be copied or reproduced in any form without prior consent.

DYNEX Technologies reserves the right to make technical improvements to this equipment and documentation without prior notice as part of a continuous program of product development. This manual supersedes all previous editions.

Image 2

Dynex Part No. 91000051, Revision B, This manual is published by DYNEX Technologies, Inc

Contents

User’s Guide Please read carefully before using the Opsys MWOpsys MW Microplate Washer DYNEX Technologies 14340 Sullyfield Circle Part No. 91000051, Revision BThis manual is published by DYNEX Technologies, Inc Chantilly, VA 20151-1683 USA Tel. 703 800 288-2354 Fax. 703 Warranty and Special Provisions Limited Warranty Page Chapter 2 Installation Table of ContentsTable of Contents Chapter 3 Configuration Index Chapter 7 TroubleshootingChapter 8 Service Opsys MW User’s Guide This manual gives you the information needed to About this ManualAbout this Manual This page is intentionally left blank Description Chapter 1 IntroductionDescription Programming Description Wash HeadWash Head Description Wash Head PositionsWash Head Position Dispense Height Wash Fluid Waste Opsys MW User’s Guide Features Features Opsys MW User’s Guide Power Requirements SpecificationsDimensions and Weight Specifications Plate Setup Input RangesStandards Assay Programming Label Description Warning LabelsWarning Labels Opsys MW User’s Guide Unpacking Chapter 2 Installation UnpackingMaterials Provided To unpack the components Hardware Components Hardware Components Keypad. The keypad is used by the operator to select commands and enter wash parameters Connectors at the rear of the Opsys MW system are shown in Figure Figure 3. Rear View of the Opsys MW System Positioning the Instrument Positioning the Instrument Installing the Wash Head Installing the Wash Head Installing the Wash Container Installing the Wash ContainerTo install the Wash Container Installing the Waste Container Installing the Waste ContainerTo install the Waste Container and Foam/Aerosol Trap SETUP PROGRAM Turning on the SystemTurning on the System 1. Connect the Opsys MW to the laboratory electrical supply outlet 7 8 9 Chapter 3 Configuration The KeypadThe Keypad Scroll keys “Cancel” keyPurpose If you are entering or editing information , a The numeral shown on the key is displayed by AlphanumericKeys pressing the key once. If the key is pressed two to Menus SETUPConfigure the Instrument Menus The SETUP Menu The PROGRAM Menu Command Configuring the SystemConfiguring the System CLEAN Specifying the Wash Head Specifying Plate Parameters To specify parameters for a plate type Note The default value is displayed. Select SHOW to move the wash head to the default well top position so that the height can be checked. Then, determine the correct value as outlined on page 30. Repeat the procedure as needed Sweep height? SHOW Opsys MW User’s Guide Displaying the Software Version Specifying the Pump Parameters Note Refer to page 74 for additional pump calibration instructions Selecting Clean Opsys MW User’s Guide Operation Chapter 4 Wash Protocols Wash Protocol OperationsWash Protocol Operations Purge Fill DispenseSoak Creating a New Wash Protocol Creating a New Wash ProtocolSpecifying the Header To create a new wash protocol header Variable strips? YESNO 7. Re-enter the password and press ENTER. The display will readSelect plate 2 DYNEX1 9. If YES is selected, the display will read Constant timing? YESNO Select option MOVE PURGE Specifying Wash Cycle Operations To specify a Purge To specify a Move cycle To specify an Aspiration within a Move Note An Aspirate or Dispense must be To specify a Dispense within a Move Note A Dispense or Aspirate must be performed within a Move cycle Select option ASPIRATE DISPENSE To specify a Soak within a Move Note A Fill must be performed within a Move cycle To specify a Fill within a MoveNote A volume ranging from 50 to 300 microliters can be entered 2. Scroll right to display the next selection. The display will read Ending a MOVE CycleSelect option SOAK FILL Select option END LOOP 3. Select END LOOP. The display will read To specify a Soak outside of a Move To specify the End of the wash protocol Select option SOAK END 2. Select END. The display will read 1 NAME01 Modifying a Wash Protocol Modifying a Wash ProtocolTo modify a wash protocol MOVE To modify a wash operation To delete a wash operation To insert a wash operation Copying a Wash Protocol Copying a Wash ProtocolTo copy a wash protocol 7 NAME04 SETUP PROGRAM Overwrite test? NO YESNO 8. Select YES. The display will read To empty the waste container Chapter 5 Washing a PlatePreparation Preparation To refill the wash container Washing a Plate Washing a PlateTo wash a plate Opsys MW User’s Guide Weekly maintenance Chapter 6 Routine Maintenance Routine Maintenance ProceduresDaily maintenance Six month maintenance As required maintenance Cleaning and Decontamination Cleaning and DecontaminationTo clean the system To decontaminate the system Cleaning the Containers Cleaning the ContainersTo empty and clean the waste container Replacing the Tubing Replacing the TubingTo replace the dispense tubing To replace the vacuum tubing To replace the waste tubing Pump Calibration Pump CalibrationCalibration Protocol 8. If the dispensed volume is too high, decrease the pump speed using the SETUP/CAL function refer to page Opsys MW User’s Guide Symptom Chapter 7 Troubleshooting Operational ProblemsOperational Problems Resolution Resolution waste container is Z Motor Home High Waste LevelX Motor Home Test Too Large is To clean the wash head assembly Chapter 8 Service Service ProceduresTo remove the wash head assembly To replace the wash head assembly Major Assemblies AccessoriesSpare Parts Hardware Returning a Washer for Service Returning a Washer for ServiceTo return a Washer for service CERTIFICATE OF DECONTAMINATION EQUIPMENT IN TRANSITEQUIPMENT DECLARATION Suggested decontamination methods DYNEX Technologies 14340 Sullyfield Circle Chantilly, VA 20151 USA Contact DYNEX TechnologiesContact DYNEX Technologies Index Index variable strips, 41 warning labels, 11 Wash Container, 5