Opsys MW Microplate Washer
Please read carefully before using the Opsys MW
User’s Guide
DYNEX Technologies 14340 Sullyfield Circle
Part No. 91000051, Revision B
This manual is published by DYNEX Technologies, Inc
Chantilly, VA 20151-1683 USA Tel. 703 800 288-2354 Fax. 703
Warranty and Special Provisions Limited Warranty
Page
Chapter 2 Installation
Table of Contents
Table of Contents
Chapter 3 Configuration
Index
Chapter 7 Troubleshooting
Chapter 8 Service
Opsys MW User’s Guide
About this Manual
About this Manual
This manual gives you the information needed to
This page is intentionally left blank
Description
Chapter 1 Introduction
Description
Programming
Wash Head
Wash Head
Description
Description
Wash Head Positions
Wash Head Position
Dispense Height
Wash Fluid
Waste
This page is intentionally left blank
Features
Features
This page is intentionally left blank
Power Requirements
Specifications
Dimensions and Weight
Specifications
Plate Setup
Input Ranges
Standards
Assay Programming
Warning Labels
Warning Labels
Label Description
This page is intentionally left blank
Materials Provided
Chapter 2 Installation Unpacking
Unpacking
To unpack the components
Hardware Components
Hardware Components
Keypad. The keypad is used by the operator to select commands and enter wash parameters
Connectors at the rear of the Opsys MW system are shown in Figure
Figure 3. Rear View of the Opsys MW System
Positioning the Instrument
Positioning the Instrument
Installing the Wash Head
Installing the Wash Head
To install the Wash Container
Installing the Wash Container
Installing the Wash Container
To install the Waste Container and Foam/Aerosol Trap
Installing the Waste Container
Installing the Waste Container
SETUP PROGRAM
Turning on the System
Turning on the System
1. Connect the Opsys MW to the laboratory electrical supply outlet
The Keypad
Chapter 3 Configuration The Keypad
7 8 9
Scroll keys
“Cancel” key
Purpose
If you are entering or editing information , a
The numeral shown on the key is displayed by
Alphanumeric
Keys
pressing the key once. If the key is pressed two to
Menus
SETUP
Configure the Instrument
Menus
The SETUP Menu
The PROGRAM Menu
Command
Configuring the System
Configuring the System
CLEAN
Specifying the Wash Head
Specifying Plate Parameters
To specify parameters for a plate type
Note The default value is displayed. Select SHOW to move the wash head to the default well top position so that the height can be checked. Then, determine the correct value as outlined on page 30. Repeat the procedure as needed
Sweep height? SHOW
Select option HEAD PLATE
Displaying the Software Version
Specifying the Pump Parameters
Note Refer to page 74 for additional pump calibration instructions
Selecting Clean
This page is intentionally left blank
Operation
Chapter 4 Wash Protocols Wash Protocol Operations
Wash Protocol Operations
Purge
Soak
Dispense
Fill
Specifying the Header
Creating a New Wash Protocol
Creating a New Wash Protocol
To create a new wash protocol header
Variable strips? YESNO
7. Re-enter the password and press ENTER. The display will read
Select plate 2 DYNEX1
9. If YES is selected, the display will read Constant timing? YESNO
Select option MOVE PURGE
Specifying Wash Cycle Operations
To specify a Purge
To specify a Move cycle
To specify an Aspiration within a Move
Note An Aspirate or Dispense must be
To specify a Dispense within a Move
Note A Dispense or Aspirate must be performed within a Move cycle
Select option ASPIRATE DISPENSE
To specify a Soak within a Move
Note A volume ranging from 50 to 300 microliters can be entered
To specify a Fill within a Move
Note A Fill must be performed within a Move cycle
2. Scroll right to display the next selection. The display will read
Ending a MOVE Cycle
Select option SOAK FILL
Select option END LOOP 3. Select END LOOP. The display will read
To specify a Soak outside of a Move
To specify the End of the wash protocol
Select option SOAK END 2. Select END. The display will read 1 NAME01
To modify a wash protocol
Modifying a Wash Protocol
Modifying a Wash Protocol
MOVE
To modify a wash operation
To delete a wash operation
To insert a wash operation
To copy a wash protocol
Copying a Wash Protocol
Copying a Wash Protocol
7 NAME04 SETUP PROGRAM
Overwrite test? NO YESNO 8. Select YES. The display will read
To empty the waste container
Chapter 5 Washing a Plate
Preparation
Preparation
To refill the wash container
To wash a plate
Washing a Plate
Washing a Plate
This page is intentionally left blank
Weekly maintenance
Chapter 6 Routine Maintenance Routine Maintenance Procedures
Daily maintenance
Six month maintenance
As required maintenance
Cleaning and Decontamination
Cleaning and Decontamination
To clean the system
To decontaminate the system
To empty and clean the waste container
Cleaning the Containers
Cleaning the Containers
To replace the dispense tubing
Replacing the Tubing
Replacing the Tubing
To replace the vacuum tubing
To replace the waste tubing
Calibration Protocol
Pump Calibration
Pump Calibration
8. If the dispensed volume is too high, decrease the pump speed using the SETUP/CAL function refer to page
This page is intentionally left blank
Symptom
Chapter 7 Troubleshooting Operational Problems
Operational Problems
Resolution
Resolution
waste container is
Z Motor Home
High Waste Level
X Motor Home
Test Too Large is
To clean the wash head assembly
Chapter 8 Service Service Procedures
To remove the wash head assembly
To replace the wash head assembly
Major Assemblies
Accessories
Spare Parts
Hardware
To return a Washer for service
Returning a Washer for Service
Returning a Washer for Service
CERTIFICATE OF DECONTAMINATION
EQUIPMENT IN TRANSIT
EQUIPMENT DECLARATION
Suggested decontamination methods
Contact DYNEX Technologies
Contact DYNEX Technologies
DYNEX Technologies 14340 Sullyfield Circle Chantilly, VA 20151 USA
Index
Index
variable strips, 41 warning labels, 11 Wash Container, 5
