To delete a wash operation | Dynex 91000051 specification

Modifying a Wash Protocol

To delete a wash operation:

1.Select DELETE while the operation is displayed. The operation is removed from the wash protocol.

Note: If a MOVE operation is deleted, all operations within the MOVE (i.e., Aspirate, Dispense, Soak and Fill) are also removed.

Opsys MW™ User’s Guide

59

Image 67

Dynex 91000051 manual To delete a wash operation, Modifying a Wash Protocol

Contents

Opsys MW Microplate Washer Please read carefully before using the Opsys MWUser’s Guide Chantilly, VA 20151-1683 USA Tel. 703 800 288-2354 Fax. 703 Part No. 91000051, Revision BThis manual is published by DYNEX Technologies, Inc DYNEX Technologies 14340 Sullyfield Circle Warranty and Special Provisions Limited Warranty Page Chapter 3 Configuration Table of ContentsTable of Contents Chapter 2 Installation Opsys MW User’s Guide Chapter 7 TroubleshootingChapter 8 Service Index About this Manual About this ManualThis manual gives you the information needed to This page is intentionally left blank Description Chapter 1 IntroductionDescription Programming Wash Head Wash HeadDescription Dispense Height Wash Head PositionsWash Head Position Description Waste Wash Fluid This page is intentionally left blank Features Features This page is intentionally left blank Specifications SpecificationsDimensions and Weight Power Requirements Assay Programming Input RangesStandards Plate Setup Warning Labels Warning LabelsLabel Description This page is intentionally left blank Materials Provided Chapter 2 Installation UnpackingUnpacking To unpack the components Hardware Components Hardware Components Keypad. The keypad is used by the operator to select commands and enter wash parameters Figure 3. Rear View of the Opsys MW System Connectors at the rear of the Opsys MW system are shown in Figure Positioning the Instrument Positioning the Instrument Installing the Wash Head Installing the Wash Head To install the Wash Container Installing the Wash ContainerInstalling the Wash Container To install the Waste Container and Foam/Aerosol Trap Installing the Waste ContainerInstalling the Waste Container 1. Connect the Opsys MW to the laboratory electrical supply outlet Turning on the SystemTurning on the System SETUP PROGRAM The Keypad Chapter 3 Configuration The Keypad7 8 9 If you are entering or editing information , a “Cancel” keyPurpose Scroll keys pressing the key once. If the key is pressed two to AlphanumericKeys The numeral shown on the key is displayed by Menus SETUPConfigure the Instrument Menus The PROGRAM Menu The SETUP Menu CLEAN Configuring the SystemConfiguring the System Command Specifying the Wash Head Specifying Plate Parameters To specify parameters for a plate type Note The default value is displayed. Select SHOW to move the wash head to the default well top position so that the height can be checked. Then, determine the correct value as outlined on page 30. Repeat the procedure as needed Sweep height? SHOW Select option HEAD PLATE Displaying the Software Version Note Refer to page 74 for additional pump calibration instructions Specifying the Pump Parameters Selecting Clean This page is intentionally left blank Purge Chapter 4 Wash Protocols Wash Protocol OperationsWash Protocol Operations Operation Soak DispenseFill Specifying the Header Creating a New Wash ProtocolCreating a New Wash Protocol To create a new wash protocol header 9. If YES is selected, the display will read Constant timing? YESNO 7. Re-enter the password and press ENTER. The display will readSelect plate 2 DYNEX1 Variable strips? YESNO Select option MOVE PURGE Specifying Wash Cycle Operations To specify a Purge To specify a Move cycle Note An Aspirate or Dispense must be To specify an Aspiration within a Move Note A Dispense or Aspirate must be performed within a Move cycle To specify a Dispense within a Move Opsys MW User’s Guide To specify a Soak within a Move Note A volume ranging from 50 to 300 microliters can be entered To specify a Fill within a MoveNote A Fill must be performed within a Move cycle Select option END LOOP 3. Select END LOOP. The display will read Ending a MOVE CycleSelect option SOAK FILL 2. Scroll right to display the next selection. The display will read To specify a Soak outside of a Move Select option SOAK END 2. Select END. The display will read 1 NAME01 To specify the End of the wash protocol To modify a wash protocol Modifying a Wash ProtocolModifying a Wash Protocol MOVE To modify a wash operation To delete a wash operation To insert a wash operation To copy a wash protocol Copying a Wash ProtocolCopying a Wash Protocol Overwrite test? NO YESNO 8. Select YES. The display will read 7 NAME04 SETUP PROGRAM Preparation Chapter 5 Washing a PlatePreparation To empty the waste container To refill the wash container To wash a plate Washing a PlateWashing a Plate This page is intentionally left blank Six month maintenance Chapter 6 Routine Maintenance Routine Maintenance ProceduresDaily maintenance Weekly maintenance As required maintenance To decontaminate the system Cleaning and DecontaminationTo clean the system Cleaning and Decontamination To empty and clean the waste container Cleaning the ContainersCleaning the Containers To replace the dispense tubing Replacing the TubingReplacing the Tubing To replace the vacuum tubing To replace the waste tubing Calibration Protocol Pump CalibrationPump Calibration 8. If the dispensed volume is too high, decrease the pump speed using the SETUP/CAL function refer to page This page is intentionally left blank Resolution Chapter 7 Troubleshooting Operational ProblemsOperational Problems Symptom Probable Cause waste container is Test Too Large is High Waste LevelX Motor Home Z Motor Home To replace the wash head assembly Chapter 8 Service Service ProceduresTo remove the wash head assembly To clean the wash head assembly Hardware AccessoriesSpare Parts Major Assemblies To return a Washer for service Returning a Washer for ServiceReturning a Washer for Service Suggested decontamination methods EQUIPMENT IN TRANSITEQUIPMENT DECLARATION CERTIFICATE OF DECONTAMINATION Contact DYNEX Technologies Contact DYNEX TechnologiesDYNEX Technologies 14340 Sullyfield Circle Chantilly, VA 20151 USA Index Index variable strips, 41 warning labels, 11 Wash Container, 5