Manuals / Emerson / Computer Equipment / Power Supply

Emerson 540VDC manual System Mode Indicators, System Status Indicators, Operation modes

Models: 540VDC

1 168

Download 168 pages 31.68 Kb

Page 67

Operation

6.2.2System MODE Indicators

The Liebert FS has nine modes of operation: OFF, STARTUP, CHARGE, READY, DISCHARGE, SHUTDOWN, COAST, FAULT and STANDBY. These are displayed on the main screen of the control panel as identified in Figure 55. Table 5 lists the system Modes along with the corresponding Con- tactor Status, and the Conditions required to operate in these Modes: external voltage range, speed and command.

NOTE:

See 5.3 - Modes of Operation for further details on modes of operation.

Table 5	Operation modes

				Condition
Mode		Contactor
Mode		Contactor	External Voltage	Speed	Command

OFF		Open	Vext < Vchg	0 ~ 3500	—

STANDBY		Open	Vext > Vchg	0 ~ 200	—

STARTUP		Close	Vext > Vchg	200 ~ Min Speed	STARTUP

CHARGE		Close	Vext > Vchg	Min Speed ~ Max Speed	STARTUP

READY		Close	Vext > Vchg	Max Speed ~ Max Speed + 200	STARTUP

DISCHARGE		Close	Vext < Vchg	Min Speed ~ Max Speed	STARTUP

COAST		Close	330 < Vext < Vchg	200 ~ Min Speed	STARTUP

SHUTDOWN		Open	Vext < 330	200 ~ Min Speed	STARTUP

		Open	Any	Min Speed ~ Max Speed	SHUTDOWN

		Close	Vext > 330	200 ~ Min Speed	SHUTDOWN

FAULT		Open	Any	0 ~ Max Speed	—

STANDBY		—		After CLRFLT

Min Speed: Minimum operating speed; State of Charge (SOC) will be 0% at this speed.

Max Speed: Maximum operating speed; State of Charge (SOC) will be 100% at this speed.

6.2.3System STATUS Indicators

The Liebert FS system displays multiple status conditions during operation. Table 6 shows the com- plete list of status indicators for the Liebert FS and the corresponding condition.

Table 6 System status indicators

	Message	Condition

1	OK	All systems operating normally.

2	READY	All systems operational and ready for startup.

3	APPLY 520*V	External voltage is less than the Charge Voltage*

4	n WARNINGS	Multiple warnings

5	n FAULTS	Multiple faults

6	OVERSPEED	Speed is higher than the Max Speed plus 200 RPM

7	TESTING VACUUM	Vacuum testing at 10000 RPM

8	OPENING CONTACTOR	Waiting until the current is stabilized

9	CLOSING CONTACTOR	Waiting until the voltages are stabilized

10	WAIT	Waiting until the voltages are stabilized

* Charge voltage is an adjustable user parameter; 520V is used only as an example.

55	DISCONTINUED
	PRODUCT

Image 67

Emerson 540VDC manual System Mode Indicators, System Status Indicators, Operation modes, System status indicators

Contents

Liebert FS DC Energy Storage System DIS Product Table of Contents Operation System OverviewTroubleshooting MaintenanceAppendix B.0 Data Collection Module Appendix A.0 UPS Interconnection KitsAppendix C.0 Versatile Interface Board Appendix D.0 Installation DrawingsAppendix E.0 Specifications Appendix F.0 Auxiliary Backup AC Power SupplyFigures Vii Versatile Interface Board mounted in the Liebert FS 110 Tables Product Important Safety Instructions Safety Precautions System information Safety ConsiderationsGeneral Information Requesting Assistance from LiebertLiebert FS General System DescriptionLiebert FS Unit DC Bus LoadsLiebert FS Unit N FS Unit N Battery NGeneral Specifications LiebertApplicable Standards and Certification Features and BenefitsKey Technological Features Key Customer BenefitsKW-sec delivered GTX model, 520 VDC, with filter Output Power vs. Ride-Through Time Vbus=540V, Vreg=520VBypass Utility Static SwitchRectifier Environmental Considerations System LocationElectrical Considerations Flooring RequirementsRemote Monitoring Connections-Optional AC Power ConnectionsStatus/Control Connections Grounding ConnectionsUnloading Inspection Before Removal From the Truck14623 Unpacking HandlingRemoving the metal support plates Lifting the Liebert FS cabinetManuals Serial Number Model Number Plates Storing the Liebert FS for Delayed InstallationPositioning the Liebert FS Moving the Liebert FSBottom TopFront Right Side 12-100120-09 Front Right Side Door open Panel removed Internal layoutFloor Mounting Bracket Cabinet Floor MountingConcrete, Masonry or Stone Floor Mounting Instructions Mounting ToolsChecking hole depth 12.7mm Floor to Flange Bolt securing bracket to cabinetBubble level Mounting front bolts-front side of cabinetWood Floor Mounting Instructions Wood Floor MountingWood Floor Mounting Parts Wood Floor Mounting ToolsRaised Floor Mounting Tools Raised Floor Mounting Raised Floor Mounting KitRaised Floor Mounting Instructions Rear Wiring ConnectionsGeneral Wiring Considerations FrontCircuit Breaker Mounting Plate Control Communication Access Panel DC and Ground ConnectionsPounds Ground Wire Gauge Tightening Torque Approximate metric InchGround Connections Tightening torque for ground connectionService panel location AC Auxiliary Control Power Supply ConnectionsTerminal Neutral Ground Terminal 2 Line Fused disconnectRemote monitoring DCM connections inside cabinet front door Startup ConsiderationsLiebert FS front view Detailed System DescriptionUPS Interconnection Kit Power Conversion ModuleSystem Module Description Control PanelMagnetic Levitation Power SystemElectrical system schematic Battery InputData Collection Module DCM User interfaces Control PanelVersatile Interface Board VIB Igbt Power Conversion Module PCM Active Magnetic Levitation Hardware Magnetic Levitation Module MLMUpper Radial Axial ElectromagnetMotor Generator Rotor/Flywheel-Rotating GroupVacuum system operation Vacuum SystemFlywheel Sensors Speed TemperatureOuter Housing Rotating Group Inner Housing Coolant System SafetyCabinet List of System User-Configurable Parameters Max Charge Current Voltage Behavior Current Sink Regulation Voltage Delta During Discharge Vreg DeltaVreg delta help screen Modes of OperationUPS DC Bus Voltage = Vcharge OFF ModeStandby Mode Startup ModeReady Mode Charge ModeVoltage ≥ Vcharge Shutdown Mode Discharge ModeFollowing a Liebert FS Discharge Down to SOC = 0% Coast Mode Following a User CommandFault Mode Typical operation modes KEY # Mode DescriptionMaintenance and Reliability Operator Controls Access System HistoryControl panel keyboard layout refer to Figure System Status IndicatorsSystem Mode Indicators Control PanelMain screen function descriptions Operation modes System Mode IndicatorsSystem Status Indicators System status indicatorsOperative DisabledUninstalled Other Status IndicatorsMenu Tree and Navigation Security AccessMenu tree Navigation and Operation of Control Panel System Setup and Parameter Access2V REG Time/Date ViewVoltages TemperaturesHistory Discharge history Fault history, Event list screenVitals history view OptionsNetworks view Network-Requires DCM OptionVitals ElectricalSecurity Password screens Tools AboutSystem Startup Initial System Startup ProcedureInspection before Initial System Startup Software versions Control Parameters Setup at Initial System StartupControl Parameter Value Default Control parametersInspection Before Regular Startup Regular Startup ProcedurePowering Up the Liebert FS Booting UpLiebert FS Startup Sequence Shutdown ProcedureValidation of Control Parameters Setup Initiating Liebert FS Startup SequenceSafety Precautions Routine Maintenance Liebert ServicesRecord Log Maintenance ScheduleMaintenance schedule Frequency Service Every Item/Action YrsDetecting Trouble Torque specifications unless otherwise labeledOptional Air Filters Torque RequirementsLimited Life Components Reporting a ProblemCorrective Actions Recommended Test EquipmentUser level menu GeneralButton F5 Ore informationAuxpower Meaning / Possible Causes Troubleshooting LabelBus Power FaultsOre information Fault Clear Button F3 Button F5 BUS Current Offset Faults-causes and responsesTroubleshooting Fault Label Troubleshooting Action Liebert FS Model # Use With Liebert UPS Appendix A.1 Wiring ConnectionsAppendix A.1.1 General Wiring Considerations Key to UPS model interconnectionTop view of Liebert FS Cabinet with UPS interconnection kit RearCircuit Breaker Torque Appendix A.1.2 DC Power ConnectionsLiebert FS Positive Terminal Negative UPS Output Rating KVA Liebert Series 610/600T/600 model ratingsYellow Blue Two rows Row for Liebert FS Software Control Parameter Setting Liebert FS Software Control Parameter settingsRating Liebert Npower model ratingsLiebert FS Npower UPS OutputLiebert FS Software Control Parameters Liebert FS Software Setting Control ParameterSee Table Product Liebert Series 300 UPS List of Liebert Series 300 models ratingsLiebert Series 300 status/control terminal block wiring 395VDC Liebert HiPulse model ratings Appendix A.5.1 Description-HiPulse UPS Interconnection KitLiebert FS positive terminal Liebert FS negative terminal Appendix A.5.3 IKIT-A05 DC Power ConnectionsUPS Output Rating kVA 120 Appendix A.5.5 Single Liebert FS on UPS DC BusMultiple Liebert FS Parallel Operation-Regular Configuration Appendix B.1 General Information Appendix B.2 DCM Installation and ConfigurationAppendix B.1.2 Features Appendix B.2.1 InstallationAppendix B.2.2 DCM Requirements LAN Connection Power ConnectionHome Done Appendix B.2.4 Configuring DCM System Parameters Appendix B.2.3 Accessing the DCMEnter IP Address Appendix B.3.1 Logging into the DCM Appendix B.3 DCM OperationAppendix B.3.2 Status and Detailed Status Screens Datafiles screen Appendix B.3.3 Datafiles ScreenTroubleshooting Appendix B.4 DCM TroubleshootingAppendix B.4.1 DCM Troubleshooting Principles Appendix B.4.2 Resetting the DCMAppendix C.1.1 Versatile Interface Board Overview Appendix C.1 General Information-Versatile Interface BoardVIB I/O functions Interface VIB Designation Description Appendix C.1.2 VIB FeaturesLabel X20Appendix C.2.4 VIB Output Specifications Appendix C.2 VIB Installation and ConfigurationAppendix C.2.1 VIB Installation Appendix C.2.3 VIB Input SpecificationsAppendix C.3 VIB Operation Appendix C.4.3 Inputs Not Recognized Appendix C.4 Troubleshooting the VIBAppendix C.4.2 VIB in Disabled or Not Available State Appendix C.4.1 UIB State Not Displayed on the Front PanelAppendix D.1 Liebert FS Flywheel Submittal Document Matrix Storage Solution Flywheel Storage SolutionSubmittal documents accompanying Liebert FS Appendix D.2 Other Liebert FS Drawings No UVR, circuit breaker to terminal block wiringElectrical connections Electrical system block diagram 48 UVR, circuit breaker to terminal block wiring 24 UVR, circuit breaker to terminal block wiringOutline drawing, Liebert FS cabinet Fused Liebert FS FS cabinet to Liebert Series 610 UPS module ControlMetal Support Front Elevation drawing-Liebert FS cabinet124 NEG Mechanical Weight 1300 lb .6kgNEG POS GND Line drawing, three Liebert FS systems in parallel configurationBreaker + GNDWith Liebert UPS Liebert UPS Module + GND With factory-integrated circuit Parallel with aLiebert UPS Module Liebert UPS Module Status/control Wiring, multiple unitsWiring specifications, Liebert FS and Liebert Series Wiring specifications, Liebert FS and Liebert Npower Wiring specifications, Liebert FS and Liebert Series 140 29-1/2 749mm Bolts and Washers come with cabinet Drill Template Dwg Liebert FS block diagram Power line diagram Liebert FS Cabinet Liebert FS Cabinet Unit NUnit N Input Bus Unit N Input UPS cable entry-topTOP View Technical specifications Appendix E.0 SpecificationsItems Required Appendix E.1 Ground Test ProcedureFrequency 50 to 60Hz Appendix F.2 Backup AC Power Supply SpecificationAppendix F.3 Recommended Backup Power Supply Configuration Appendix F.1 OverviewGrid supply DC bus Battery Liebert FS PackGrid Appendix F.3.2 Operating the Liebert FS Without Batteries Liebert FS Flywheel module Appendix F.4 Scenarios154 DIS Product Locations