HYDRA

Service Manual

7-5. Main PCA Connector

The IEEE-488 PCA interfaces to the Main PCA through a 26-pin, right-angle connector (A5J1). This connector routes the 8-bit data bus, the lower three bits of the address bus, memory control, system clock, and address decode signals from the Main PCA to the IEEE-488 PCA. The IRQ2* interrupt request signal is routed from the IEEE-488 PCA to the Main PCA. The IEEE-488 PCA is powered by the +5.1V dc power supply (VCC). The IEEE-488 PCA is sensed by the Microprocessor on the Main PCA through the connection of logic common to the option sense signal OPS* (A5J1-22).

7-6. IEEE-488 Controller

The IEEE-488 Controller (A5U1) is an integrated circuit that performs the transfer of information between the IEEE-488 standard bus and the Main PCA Microprocessor (A1U4). Once it has been programmed by the Microprocessor via the eight-register microprocessor interface, A5U1 performs IEEE-488 bus transactions independently until it must interrupt the Microprocessor for additional information or data.

The IEEE-488 Controller is clocked by a 1.2288-MHz square-wave clock. This clock (A5U1-20) is generated by the Microprocessor. The IEEE-488 Controller uses this clock to run the internal state machines that handle IEEE-488 bus transactions. The IEEE-488 Controller is reset when the system RESET* signal (A5U1-21) is low.

For each character that it receives or transmits, the IEEE-488 Controller generates an interrupt to the Microprocessor. These interrupts are generated by driving the open-drain interrupt output A5U1-10 low. This signal drives the IRQ2* input to the Microprocessor low. When the Microprocessor responds to the interrupt and takes the necessary actions by reading and writing registers in the IEEE-488 Controller, A5U1-10 goes high again. Resistor A5R1 provides a pull-up termination on open-drain interrupt output A5U1-10.

When the Microprocessor performs a memory cycle to the IEEE-488 Controller, the lower three bits of the address bus select the register being accessed in A5U1. When a memory read cycle is performed, chip-enable A5U1-4 goes low, and A5U1-6 (DBIN) goes high. These actions enable A5U1, driving the contents of the selected register onto the data bus to the Microprocessor. When a memory write cycle is performed, chip- enable A5U1-4 goes low, and A5U1-5 (WE*) goes first low and then high to latch the data being driven from the Microprocessor into the IEEE-488 Controller.

The IEEE-488 Controller interfaces to the IEEE-488 Transceivers using an eight-bit data bus, eight interface signals, and two transceiver control signals (A5U1-33 and A5U1- 23).

The controller-in-charge signal (A5U1-33), which should always be high, controls the direction of the SRQ, ATN, IFC, and REN IEEE-488 transceivers in A5U3.

The talk enable output (A5U1-2) is either low when the IEEE-488 Controller is not addressed to talk or high when the controller is addressed to talk. This signal determines the direction of all IEEE-488 Transceivers except SRQ, ATN, IFC, and REN.

7-4

Page 276
Image 276
Fluke 2635A, 2625A service manual Main PCA Connector, IEEE-488 Controller

2635A, 2625A specifications

The Fluke 2625A is a sophisticated data logger designed for a wide range of industrial and laboratory applications. This versatile instrument excels in capturing and monitoring temperature and voltage measurements with precision and reliability. One of its standout features is its ability to record data from various sensors, making it ideal for environments where comprehensive data acquisition is critical.

Equipped with a large LCD display, the Fluke 2625A provides clear and user-friendly access to real-time measurement data. Its graphical interface allows users to visualize trends and monitor readings easily, which significantly enhances usability. The device supports a variety of input types and can connect to thermocouples, RTDs, and other sensors, offering great flexibility for various measurement tasks.

The Fluke 2625A employs advanced measurement technologies that ensure accuracy in data logging. With a high sampling rate, it captures fast-changing signals while maintaining data integrity. The device features a built-in memory that allows for extensive logging, accommodating long-term monitoring tasks without requiring constant oversight. Users can set it to log data at specified intervals, offering customizable solutions for different monitoring needs.

Another significant characteristic of the Fluke 2625A is its robust communication capabilities. The device supports USB and RS-232 interfaces for easy connectivity with computers and other devices, making data transfer and analysis seamless. This feature is especially beneficial for users who need to compile or analyze large sets of data quickly.

Furthermore, the Fluke 2625A is designed with durability in mind. Its rugged construction makes it suitable for challenging environments, including those with high levels of vibration, dust, or moisture. This reliability ensures that the device can withstand the rigors of fieldwork while still delivering accurate measurements.

In summary, the Fluke 2625A is a powerful data logger that combines versatility, accuracy, and reliability. Its user-friendly interface, advanced measurement technologies, and robust design make it an essential tool for professionals in various industries, from manufacturing and HVAC to research and development. Whether monitoring temperature changes in a laboratory or assessing voltage levels in an industrial setting, the Fluke 2625A stands out as a trusted solution for effective data logging and analysis.