Copying/pasting track data, 105 | Fostex MR-8HD manual

MR-8HD Owner’s Manual (Track editing)

8) Press the [MENU/ENTER] knob.

The display now returns to the track edit menu screen, where “Erase Track >” is highlighted.

9) Press the [STOP] key to exit the menu mode.

<Note>: If you are not satisfied with the result, press the [UNDO/REDO] key to undo the operation (see page 103).

Copying/pasting track data

You can copy whole data (from ABS ZERO to REC END) of the desired track(s) of the song cur- rently loaded and paste it to the other desired track(s). The data on the source track(s) still remains after the copy/paste operation. Copy/paste operation can be done within the currently loaded song.

ABS ZERO

REC END

TRK 1

TRK 2

TRK 3

TRK 4

TRK 5

TRK 6

TRK 7

TRK 8

<Note>: You cannot copy/paste track data of a song protected. Release the protection before copying/ pasting track data.

3)Rotate the [MENU/ENTER] knob to select "Track Edit >", and press the [MENU/ENTER] knob.

The display now shows the track edit menu screen, where "<< Back" is highlighted.

1)Load the song you want to edit.

2)While the recorder is stopped, press the [MENU/ENTER] knob to enter the menu mode.

The display now shows the first page of the menu selection screen, where "<< Back" is highlighted initially (selecting "<< Back" returns to the previous screen).

4)Rotate the [MENU/ENTER] knob to select "Copy-Paste Track >", and press the [MENU/ENTER] knob.

The display now shows the screen for selecting the source track(s) and destination track(s) of copy/paste operation.

"Source Track" selects the copy source track(s), while "Dest. Track" selects the paste destination track(s).

105

Image 105

Fostex MR-8HD owner manual Copying/pasting track data, 105

Contents

8588062100 428387 Safety Instructions Important Safety Instructions Table of contents Overdubbing basics Input connectionRecording onto four tracks simultaneously Basic mixdown Track bouncing Using effectsRhythm guide function Bouncing tracks 1 through 8 to a new song 111 103100 108 131 123137 119 Read this chapter first Introduction MR-8HD main features About power supply Precautions before usingPrecautions upon installing the MR-8HD About copyrights Recording method Basics of the MR-8HD Remain recordable space left on the disk About song Bar/beat mode ABS time modeABS time mode Time base Trim control Trim controlProper level Level is too high Page Names and functions Connector and phone jack Input a input connectors XLRInput B input connectors XLR Top panel Power switch Input D input connectors XLR Connector and phone jackREVERB/DELAY Time control Peak indicators Bounce 1-4 5/6, 1-6 7/8 / ABC1 key Rhythm Guide keyTime Base SEL key Bounce 1-8 NEW Song / DEF2 key UNDO/REDO/DELETE key Bright keysSTORE/+-0 key Locate B/OUT/GHI3 key Rear panel Home screen LCD display Selecting a time base mode Adjusting the display contrastHigh contrast Menu screen Page Basic operations Power connection About powerAbout the standby mode Turning on the unit Listening the demo song Connecting headphones or a monitor speaker system Playing back the demo song Release the song protection see 101Format the hard disk see page 124 Make recording Enter the desired song name Creating a song for recording How to enter characters Character entry keysCharacter entry example Input a SEL switch Input connectionInput channel Example of input assignment to tracks Recording track combinations and available input channelsInput a Track Input B Track Input C Track Input D Track Input a and Input B are available Preparation for recording Recording onto a single track Starting recording Press the Record key once the key indicator starts flashingPlaying back the recorded track Undoing recording undo/redo Overdubbing basics GTR Clean MIC/LINE GTR Dist Press the Play key to play back the song from the beginning Adjusting the recording levels while listening to track Recording onto four tracks simultaneously Set the Input a SEL switch to Guit Dist Recorder starts recording Mixdown to an analog recorder Basic mixdown Mixdown to a digital recorder Digital master recorderSet the master recorder to accept the digital input Advanced playback and locate functions Cueing Playback between Locate a and B pointsKey while holding down the Stop key Selecting a play mode Play modePlay mode off Auto play mode Loop mode Auto play mode Auto return modeLoop mode Loop function in auto punch in/out mode Time locate Locate function Locating to the Locate a or Locate B point Setting the Locate a or Locate B point Locating Punch in/out Important note Punch in/out using the keys on the top panel Punch in/out using the footswitch Setting the punch-in and punch-out points Auto punch in/outWhile the recorder is stopped, press the Locate A/IN key How to make auto punch in/out mode active Rehearsal for auto punch in/outPress the Play key Actual auto punch in/out About partPress the Record key while holding down the Play key Using effects Mic simulation effects Using the insert effectsAmp simulation effects Details of each mic simulation effect Effector Applying external effects Using the reverb or delay Selecting an effect type Selecting a delay typeDetails of each effect type Adjusting the delay/reverb time Adjusting the effect send levelsPress the Stop key to quit the menu mode Mono Selecting the desired effect type Using the mastering effectsBouncing tracks 1 through 4 to track 5/6 Bouncing tracks 1 through 8 to the New song Track bouncing Track bouncing example Preliminary knowledge 5/6 mode see Signal flow of track bouncing7/8 mode see NEW Song mode see Rehearsal of track bouncing Bouncing tracks 1 through 4 to tracks 5/6 Actual track bouncing Panning controlAuto punch in/out of track bouncing Bouncing tracks 1 through 6 to tracks 7/8 Exporting bounced data to a PC Checking the bounced signals on tracks 7/8 Fader Ing Bouncing tracks 1 through 8 to a new song Press the MENU/ENTER knob while holding down the Record key While the recorder is stopped, press the 1-8 NEW Song key Mixing Mixing signals of inputs a through D Press the Stop key to exit the menu mode Panning setting for Input a through Input D Typical bouncing Fig Bouncing the desired part Fig Bouncing the desired part of a song Rhythm guide function Setting the time signature and tempo Using the rhythm guide function Signature Time signature setting Tempo Tempo settingRhythm Guide On/off selection of the rhythm guide Conductor Map On/off selection of the conductor map Creating the conductor map Setting the signature map 2Bar starts flashing and you can now set the bar number Editing a time signature event Deleting an unnecessary time signature eventAfter deleting Default home screen bar offset = -2 bars Editing the bar offsetTo exit the menu mode, press the Stop key Setting the tempo map Tempo = 120bpm, and press Deleting an unnecessary tempo event Editing a tempo eventBefore editing After editing Midi synchronization Connection Synchronization using MTCMidi sequencer, etc MTC start time Off Synchronization using Midi clockPage Data export to a personal computer WAV file conversion Procedure of file conversionEnabling the file conversion Press the MENU/ENTER knob Enter a new name using the character entry keys Editing a file nameAfter entering a new name, press the MENU/ENTER knob Connection to a personal computer Exporting data to a personal computer Important note Protecting the hard disk 8HD to a computer default setting Using drag & drop technique Using the WAV Manager supplied by FostexArchiving a song Exporting data to a personal computerPage Select Back on a menu screen and press the MENU/ENTER knob Song managementPress the Rewind key Press the Stop key Selecting the desired song Character entry keys Editing a song nameDelete key After entering the name, press the MENU/ENTER knob 100 Deleting an unnecessary song Protecting a song 101Protect, then press the MENU/ENTER knob Tips 102 Track editing 103Select Back on a menu screen and press the MENU/ENTER knob 104 Erasing track data 105 Copying/pasting track data 106 107 Moving track data 108 Exchanging whole track data 109 110 111 Part editing 112 Changing an edit point during editingPress the Play key while holding down the Stop key 113 Erasing the parts 114 Copying/pasting the parts-1 115 Copying/pasting the parts-2 116Copying to the clipboard Pasting clipboard data 117 118 119 Moving the parts 120 121 Exchange the parts 122 123 Other functions 124 Hard disk formatting 125 Peak hold time setting 126 Pre-roll/post-roll time setting 127 Beat resolution mode on/off Phantom power on/off 128Tip 129 Initialized item Default setting Initializing the MR-8HD130 131 Troubleshooting 132 Troubles for recordingTrouble Is the recording track in the input monitor mode? 133 Troubles for playback Troubles for USB connection Troubles for effect134 Is the USB cable connected correctly? Other troubles 135Is the Rhythm Guide key is illuminated? 136 137 MR-8HD Specifications 138 Specifications 139 Physical dimensions When using the normal mode Block diagramWhen using the bounce mode 1-4 5/6 mode 140 When using the bounce mode 1-6 7/8 mode When using the bounce mode 1-8 New Song mode141 142 Midi Implementation Chart 143 Index 144 Declaration of EC DirectivePage 428387