106 | Fostex MR-8HD instruction

MR-8HD Owner’s Manual (Track editing)

5)Rotate the [MENU/ENTER] knob to select "Source Track = *", and press the [MENU/ENTER] knob.

You can now select the desired copy source track(s) by rotating the [MENU/ENTER] knob. The available options are:

•1 through 8 (mono track)

•1/2, 3/4, 5/6 and 7/8 (stereo tracks)

7)Rotate the [MENU/ENTER] knob to select the destination track(s), and press the [MENU/ENTER] knob.

“Dest. Track = *” is now highlighted on the screen.

8)Rotate the [MENU/ENTER] knob to move the cursor to "ENTER" at the bottom of the screen, then press the [MENU/ENTER] knob.

The display shows "Please Wait", immediately followed by "Completed" when the MR-8HD completes the copy/paste operation.

<Note>: If you want to cancel the copy/paste operation, move the cursor to "[CANCEL]" on the screen, and press the [MENU/ENTER] knob.

6)Rotate the [MENU/ENTER] knob to select the source track(s) to be copied, and press the [MENU/ENTER] knob.

You can now select the desired copy destination track(s)

You can select the same number of tracks as the copy source track(s). For example, if you select a mono track for the source, you can only select a mono track for the destination.

<Note>: You cannot select the same track(s) for the copy source and destination.

<Note>: If a destination track has recorded data, pasting the copied data overwrites the previous data.

9)Press the [MENU/ENTER] knob.

The display now returns to the track edit menu screen, where “Copy-Paste Trk >” is highlighted.

10)Press the [STOP] key to exit the menu mode.

<Note>: If you are not satisfied with the re- sult, press the [UNDO/REDO] key to undo the operation (see page 103).

106

Image 106

Fostex MR-8HD owner manual 106

Contents

428387 8588062100 Safety Instructions Important Safety Instructions Table of contents Recording onto four tracks simultaneously Input connectionOverdubbing basics Basic mixdown Rhythm guide function Using effectsTrack bouncing Bouncing tracks 1 through 8 to a new song 100 103111 108 137 123131 119 Read this chapter first MR-8HD main features Introduction Precautions upon installing the MR-8HD Precautions before usingAbout power supply About copyrights Basics of the MR-8HD Recording method About song Remain recordable space left on the disk ABS time mode ABS time modeBar/beat mode Time base Trim control Trim controlProper level Level is too high Page Names and functions Input B input connectors XLR Input a input connectors XLRConnector and phone jack Top panel REVERB/DELAY Time control Input D input connectors XLR Connector and phone jackPower switch Peak indicators Time Base SEL key Rhythm Guide keyBounce 1-4 5/6, 1-6 7/8 / ABC1 key Bounce 1-8 NEW Song / DEF2 key STORE/+-0 key Bright keysUNDO/REDO/DELETE key Locate B/OUT/GHI3 key Rear panel LCD display Home screen Adjusting the display contrast Selecting a time base modeHigh contrast Menu screen Page Basic operations About the standby mode About powerPower connection Turning on the unit Connecting headphones or a monitor speaker system Listening the demo song Release the song protection see 101 Playing back the demo songFormat the hard disk see page 124 Make recording Creating a song for recording Enter the desired song name Character entry keys How to enter charactersCharacter entry example Input connection Input a SEL switchInput channel Input a Track Input B Track Input C Track Input D Track Recording track combinations and available input channelsExample of input assignment to tracks Input a and Input B are available Recording onto a single track Preparation for recording Playing back the recorded track Press the Record key once the key indicator starts flashingStarting recording Undoing recording undo/redo GTR Clean MIC/LINE GTR Dist Overdubbing basics Adjusting the recording levels while listening to track Press the Play key to play back the song from the beginning Set the Input a SEL switch to Guit Dist Recording onto four tracks simultaneously Recorder starts recording Basic mixdown Mixdown to an analog recorder Digital master recorder Mixdown to a digital recorderSet the master recorder to accept the digital input Advanced playback and locate functions Playback between Locate a and B points CueingKey while holding down the Stop key Play mode off Auto play mode Play modeSelecting a play mode Loop mode Auto return mode Auto play modeLoop mode Loop function in auto punch in/out mode Locate function Time locate Setting the Locate a or Locate B point Locating to the Locate a or Locate B point Locating Punch in/out Punch in/out using the keys on the top panel Important note Punch in/out using the footswitch Auto punch in/out Setting the punch-in and punch-out pointsWhile the recorder is stopped, press the Locate A/IN key Rehearsal for auto punch in/out How to make auto punch in/out mode activePress the Play key About part Actual auto punch in/outPress the Record key while holding down the Play key Using effects Amp simulation effects Using the insert effectsMic simulation effects Details of each mic simulation effect Applying external effects Effector Selecting an effect type Selecting a delay type Using the reverb or delayDetails of each effect type Press the Stop key to quit the menu mode Adjusting the effect send levelsAdjusting the delay/reverb time Mono Bouncing tracks 1 through 4 to track 5/6 Using the mastering effectsSelecting the desired effect type Bouncing tracks 1 through 8 to the New song Track bouncing Preliminary knowledge Track bouncing example 7/8 mode see Signal flow of track bouncing5/6 mode see NEW Song mode see Bouncing tracks 1 through 4 to tracks 5/6 Rehearsal of track bouncing Panning control Actual track bouncingAuto punch in/out of track bouncing Bouncing tracks 1 through 6 to tracks 7/8 Checking the bounced signals on tracks 7/8 Exporting bounced data to a PC Bouncing tracks 1 through 8 to a new song Fader Ing While the recorder is stopped, press the 1-8 NEW Song key Press the MENU/ENTER knob while holding down the Record key Mixing signals of inputs a through D Mixing Panning setting for Input a through Input D Press the Stop key to exit the menu mode Bouncing the desired part of a song Typical bouncing Fig Bouncing the desired part Fig Rhythm guide function Using the rhythm guide function Setting the time signature and tempo Rhythm Guide On/off selection of the rhythm guide Tempo Tempo settingSignature Time signature setting Conductor Map On/off selection of the conductor map Setting the signature map Creating the conductor map 2Bar starts flashing and you can now set the bar number Deleting an unnecessary time signature event Editing a time signature eventAfter deleting Editing the bar offset Default home screen bar offset = -2 barsTo exit the menu mode, press the Stop key Setting the tempo map Tempo = 120bpm, and press Before editing Editing a tempo eventDeleting an unnecessary tempo event After editing Midi synchronization Midi sequencer, etc Synchronization using MTCConnection MTC start time Synchronization using Midi clock OffPage Data export to a personal computer Enabling the file conversion Procedure of file conversionWAV file conversion Press the MENU/ENTER knob Editing a file name Enter a new name using the character entry keysAfter entering a new name, press the MENU/ENTER knob Exporting data to a personal computer Connection to a personal computer Important note 8HD to a computer default setting Protecting the hard disk Archiving a song Using the WAV Manager supplied by FostexUsing drag & drop technique Exporting data to a personal computerPage Press the Rewind key Song managementSelect Back on a menu screen and press the MENU/ENTER knob Press the Stop key Selecting the desired song Delete key Editing a song nameCharacter entry keys After entering the name, press the MENU/ENTER knob Deleting an unnecessary song 100 101 Protecting a songProtect, then press the MENU/ENTER knob 102 Tips 103 Track editingSelect Back on a menu screen and press the MENU/ENTER knob Erasing track data 104 Copying/pasting track data 105 106 Moving track data 107 Exchanging whole track data 108 109 110 Part editing 111 Changing an edit point during editing 112Press the Play key while holding down the Stop key Erasing the parts 113 Copying/pasting the parts-1 114 115 116 Copying/pasting the parts-2Copying to the clipboard 117 Pasting clipboard data 118 Moving the parts 119 120 Exchange the parts 121 122 Other functions 123 Hard disk formatting 124 Peak hold time setting 125 Pre-roll/post-roll time setting 126 Beat resolution mode on/off 127 128 Phantom power on/offTip 129 Initializing the MR-8HD Initialized item Default setting130 Troubleshooting 131 Trouble Troubles for recording132 Is the recording track in the input monitor mode? Troubles for playback 133 134 Troubles for effectTroubles for USB connection Is the USB cable connected correctly? 135 Other troublesIs the Rhythm Guide key is illuminated? 136 MR-8HD Specifications 137 Specifications 138 Physical dimensions 139 When using the bounce mode 1-4 5/6 mode Block diagramWhen using the normal mode 140 When using the bounce mode 1-8 New Song mode When using the bounce mode 1-6 7/8 mode141 Midi Implementation Chart 142 Index 143 Declaration of EC Directive 144Page 428387