Peak hold time setting, 125 | Fostex MR-8HD manual

MR-8HD Owner’s Manual (Other functions)

Peak hold time setting

The level meters shown on the display have the peak hold function. When it is enabled, the meter peak value during recording is held for the specified time.

The default meter peak hold time is three seconds. You can disable the peak hold function or change the peak hold time.

Peak hold indication

By default, it is held for three seconds.

1)While the recorder is stopped, press the [MENU/ENTER] knob to enter the menu mode.

The display now shows the first page of the menu selection screen, where "<< Back" is highlighted initially.

You can select between "0.1s" and "10s" in 0.1 second steps.

2)Rotate the [MENU/ENTER] knob to select "System", and press the [MENU/ENTER] knob.

The display now shows the first page of the system menu screen, where "<< Back" is highlighted.

You can select from "3s" (3 seconds, default), "1s", "2s", "5s" and "Off".

When "Off" is selected, the peak hold function is disabled (the peak value is not held).

4) Rotate the [MENU/ENTER] knob to select the desired hold time, and press the [MENU/ENTER] knob.

The peak hold setting is confirmed and the display returns to the previous screen.

5) Press the [STOP] key to exit the menu mode.

The peak hold setting is effective to all songs.

3)Rotate the [MENU/ENTER] knob to select "PeakHold Time" on the second page and press the [MENU/ENTER] knob.

The currently selected peak hold time (by default, "3s") flashes.

You can now make the desired peak hold setting.

125

Image 125

Fostex MR-8HD owner manual Peak hold time setting, 125

Contents

8588062100 428387 Safety Instructions Important Safety Instructions Table of contents Overdubbing basics Input connectionRecording onto four tracks simultaneously Basic mixdown Track bouncing Using effectsRhythm guide function Bouncing tracks 1 through 8 to a new song 111 103100 108 131 123137 119 Read this chapter first Introduction MR-8HD main features About power supply Precautions before usingPrecautions upon installing the MR-8HD About copyrights Recording method Basics of the MR-8HD Remain recordable space left on the disk About song Bar/beat mode ABS time modeABS time mode Time base Proper level Level is too high Trim controlTrim control Page Names and functions Connector and phone jack Input a input connectors XLRInput B input connectors XLR Top panel Power switch Input D input connectors XLR Connector and phone jackREVERB/DELAY Time control Peak indicators Bounce 1-4 5/6, 1-6 7/8 / ABC1 key Rhythm Guide keyTime Base SEL key Bounce 1-8 NEW Song / DEF2 key UNDO/REDO/DELETE key Bright keysSTORE/+-0 key Locate B/OUT/GHI3 key Rear panel Home screen LCD display High contrast Selecting a time base modeAdjusting the display contrast Menu screen Page Basic operations Power connection About powerAbout the standby mode Turning on the unit Listening the demo song Connecting headphones or a monitor speaker system Format the hard disk see page 124 Make recording Playing back the demo songRelease the song protection see 101 Enter the desired song name Creating a song for recording Character entry example How to enter charactersCharacter entry keys Input channel Input a SEL switchInput connection Example of input assignment to tracks Recording track combinations and available input channelsInput a Track Input B Track Input C Track Input D Track Input a and Input B are available Preparation for recording Recording onto a single track Starting recording Press the Record key once the key indicator starts flashingPlaying back the recorded track Undoing recording undo/redo Overdubbing basics GTR Clean MIC/LINE GTR Dist Press the Play key to play back the song from the beginning Adjusting the recording levels while listening to track Recording onto four tracks simultaneously Set the Input a SEL switch to Guit Dist Recorder starts recording Mixdown to an analog recorder Basic mixdown Set the master recorder to accept the digital input Mixdown to a digital recorderDigital master recorder Advanced playback and locate functions Key while holding down the Stop key CueingPlayback between Locate a and B points Selecting a play mode Play modePlay mode off Auto play mode Loop mode Loop mode Auto play modeAuto return mode Loop function in auto punch in/out mode Time locate Locate function Locating to the Locate a or Locate B point Setting the Locate a or Locate B point Locating Punch in/out Important note Punch in/out using the keys on the top panel Punch in/out using the footswitch While the recorder is stopped, press the Locate A/IN key Setting the punch-in and punch-out pointsAuto punch in/out Press the Play key How to make auto punch in/out mode activeRehearsal for auto punch in/out Press the Record key while holding down the Play key Actual auto punch in/outAbout part Using effects Mic simulation effects Using the insert effectsAmp simulation effects Details of each mic simulation effect Effector Applying external effects Details of each effect type Using the reverb or delaySelecting an effect type Selecting a delay type Adjusting the delay/reverb time Adjusting the effect send levelsPress the Stop key to quit the menu mode Mono Selecting the desired effect type Using the mastering effectsBouncing tracks 1 through 4 to track 5/6 Bouncing tracks 1 through 8 to the New song Track bouncing Track bouncing example Preliminary knowledge 5/6 mode see Signal flow of track bouncing7/8 mode see NEW Song mode see Rehearsal of track bouncing Bouncing tracks 1 through 4 to tracks 5/6 Auto punch in/out of track bouncing Actual track bouncingPanning control Bouncing tracks 1 through 6 to tracks 7/8 Exporting bounced data to a PC Checking the bounced signals on tracks 7/8 Fader Ing Bouncing tracks 1 through 8 to a new song Press the MENU/ENTER knob while holding down the Record key While the recorder is stopped, press the 1-8 NEW Song key Mixing Mixing signals of inputs a through D Press the Stop key to exit the menu mode Panning setting for Input a through Input D Typical bouncing Fig Bouncing the desired part Fig Bouncing the desired part of a song Rhythm guide function Setting the time signature and tempo Using the rhythm guide function Signature Time signature setting Tempo Tempo settingRhythm Guide On/off selection of the rhythm guide Conductor Map On/off selection of the conductor map Creating the conductor map Setting the signature map 2Bar starts flashing and you can now set the bar number After deleting Editing a time signature eventDeleting an unnecessary time signature event To exit the menu mode, press the Stop key Default home screen bar offset = -2 barsEditing the bar offset Setting the tempo map Tempo = 120bpm, and press Deleting an unnecessary tempo event Editing a tempo eventBefore editing After editing Midi synchronization Connection Synchronization using MTCMidi sequencer, etc MTC start time Off Synchronization using Midi clockPage Data export to a personal computer WAV file conversion Procedure of file conversionEnabling the file conversion Press the MENU/ENTER knob After entering a new name, press the MENU/ENTER knob Enter a new name using the character entry keysEditing a file name Connection to a personal computer Exporting data to a personal computer Important note Protecting the hard disk 8HD to a computer default setting Using drag & drop technique Using the WAV Manager supplied by FostexArchiving a song Exporting data to a personal computerPage Select Back on a menu screen and press the MENU/ENTER knob Song managementPress the Rewind key Press the Stop key Selecting the desired song Character entry keys Editing a song nameDelete key After entering the name, press the MENU/ENTER knob 100 Deleting an unnecessary song Protect, then press the MENU/ENTER knob Protecting a song101 Tips 102 Select Back on a menu screen and press the MENU/ENTER knob Track editing103 104 Erasing track data 105 Copying/pasting track data 106 107 Moving track data 108 Exchanging whole track data 109 110 111 Part editing Press the Play key while holding down the Stop key 112Changing an edit point during editing 113 Erasing the parts 114 Copying/pasting the parts-1 115 Copying to the clipboard Copying/pasting the parts-2116 Pasting clipboard data 117 118 119 Moving the parts 120 121 Exchange the parts 122 123 Other functions 124 Hard disk formatting 125 Peak hold time setting 126 Pre-roll/post-roll time setting 127 Beat resolution mode on/off Tip Phantom power on/off128 129 130 Initialized item Default settingInitializing the MR-8HD 131 Troubleshooting 132 Troubles for recordingTrouble Is the recording track in the input monitor mode? 133 Troubles for playback Troubles for USB connection Troubles for effect134 Is the USB cable connected correctly? Is the Rhythm Guide key is illuminated? Other troubles135 136 137 MR-8HD Specifications 138 Specifications 139 Physical dimensions When using the normal mode Block diagramWhen using the bounce mode 1-4 5/6 mode 140 141 When using the bounce mode 1-6 7/8 modeWhen using the bounce mode 1-8 New Song mode 142 Midi Implementation Chart 143 Index 144 Declaration of EC DirectivePage 428387