115 | Fostex MR-8HD manual

MR-8HD Owner’s Manual (Part editing)

5)Rotate the [MENU/ENTER] knob to select "Copy- PastePart >", and press the [MENU/ENTER] knob.

The display now shows the screen for selecting the source track(s) and destination track(s) of copy/paste. "<<Back" is initially highlighted.

6)Rotate the [MENU/ENTER] knob to select "Source Track = *", and press the [MENU/ENTER] knob.

The display now shows the screen for selecting the copy source track(s).

You can select the copy source track(s) by rotating the [MENU/ENTER] knob.

The available options are:

•1 through 8 (mono track)

•1/2, 3/4, 5/6 and 7/8 (stereo tracks)

7)Rotate the [MENU/ENTER] knob to select the source track(s) to be copied, and press the [MENU/ENTER] knob.

You can select the destination track(s) by rotating the [MENU/ENTER] knob.

The available options are:

•1 through 8 (mono track)

•1/2, 3/4, 5/6 and 7/8 (stereo tracks)

<Note>: You cannot select the same track(s) for the copy source and destination.

8)Rotate the [MENU/ENTER] knob to select the destination track(s), and press the [MENU/ENTER] knob.

The display returns to the previous screen.

9)Rotate the [MENU/ENTER] knob to move the cursor to "[ENTER]" at the bottom of the screen, then press the [MENU/ENTER] knob.

The display shows "Please Wait", immediately followed by "Completed" when the MR-8HD completes the copy/paste operation.

To cancel the copy/paste operation, move the cursor to "[CANCEL]" at the bottom of the screen, and press the [MENU/ENTER] knob.

10)Press the [MENU/ENTER] knob.

The display now returns to the part edit menu screen, where “Copy-Paste Part >” is highlighted.

11)Press the [STOP] key to exit the menu mode.

<Note>: If you are not satisfied with the re- sult, press the [UNDO/REDO] key to undo the operation (see page 111).

115

Image 115

Fostex MR-8HD owner manual 115

Contents

8588062100 428387 Safety Instructions Important Safety Instructions Table of contents Basic mixdown Input connectionOverdubbing basics Recording onto four tracks simultaneously Bouncing tracks 1 through 8 to a new song Using effectsTrack bouncing Rhythm guide function 108 103111 100 119 123131 137 Read this chapter first Introduction MR-8HD main features About copyrights Precautions before usingAbout power supply Precautions upon installing the MR-8HD Recording method Basics of the MR-8HD Remain recordable space left on the disk About song Time base ABS time modeBar/beat mode ABS time mode Trim control Trim controlProper level Level is too high Page Names and functions Top panel Input a input connectors XLRConnector and phone jack Input B input connectors XLR Peak indicators Input D input connectors XLR Connector and phone jackPower switch REVERB/DELAY Time control Bounce 1-8 NEW Song / DEF2 key Rhythm Guide keyBounce 1-4 5/6, 1-6 7/8 / ABC1 key Time Base SEL key Locate B/OUT/GHI3 key Bright keysUNDO/REDO/DELETE key STORE/+-0 key Rear panel Home screen LCD display Adjusting the display contrast Selecting a time base modeHigh contrast Menu screen Page Basic operations Turning on the unit About powerPower connection About the standby mode Listening the demo song Connecting headphones or a monitor speaker system Release the song protection see 101 Playing back the demo songFormat the hard disk see page 124 Make recording Enter the desired song name Creating a song for recording Character entry keys How to enter charactersCharacter entry example Input connection Input a SEL switchInput channel Input a and Input B are available Recording track combinations and available input channelsExample of input assignment to tracks Input a Track Input B Track Input C Track Input D Track Preparation for recording Recording onto a single track Undoing recording undo/redo Press the Record key once the key indicator starts flashingStarting recording Playing back the recorded track Overdubbing basics GTR Clean MIC/LINE GTR Dist Press the Play key to play back the song from the beginning Adjusting the recording levels while listening to track Recording onto four tracks simultaneously Set the Input a SEL switch to Guit Dist Recorder starts recording Mixdown to an analog recorder Basic mixdown Digital master recorder Mixdown to a digital recorderSet the master recorder to accept the digital input Advanced playback and locate functions Playback between Locate a and B points CueingKey while holding down the Stop key Loop mode Play modeSelecting a play mode Play mode off Auto play mode Auto return mode Auto play modeLoop mode Loop function in auto punch in/out mode Time locate Locate function Locating to the Locate a or Locate B point Setting the Locate a or Locate B point Locating Punch in/out Important note Punch in/out using the keys on the top panel Punch in/out using the footswitch Auto punch in/out Setting the punch-in and punch-out pointsWhile the recorder is stopped, press the Locate A/IN key Rehearsal for auto punch in/out How to make auto punch in/out mode activePress the Play key About part Actual auto punch in/outPress the Record key while holding down the Play key Using effects Details of each mic simulation effect Using the insert effectsMic simulation effects Amp simulation effects Effector Applying external effects Selecting an effect type Selecting a delay type Using the reverb or delayDetails of each effect type Mono Adjusting the effect send levelsAdjusting the delay/reverb time Press the Stop key to quit the menu mode Bouncing tracks 1 through 8 to the New song Using the mastering effectsSelecting the desired effect type Bouncing tracks 1 through 4 to track 5/6 Track bouncing Track bouncing example Preliminary knowledge NEW Song mode see Signal flow of track bouncing5/6 mode see 7/8 mode see Rehearsal of track bouncing Bouncing tracks 1 through 4 to tracks 5/6 Panning control Actual track bouncingAuto punch in/out of track bouncing Bouncing tracks 1 through 6 to tracks 7/8 Exporting bounced data to a PC Checking the bounced signals on tracks 7/8 Fader Ing Bouncing tracks 1 through 8 to a new song Press the MENU/ENTER knob while holding down the Record key While the recorder is stopped, press the 1-8 NEW Song key Mixing Mixing signals of inputs a through D Press the Stop key to exit the menu mode Panning setting for Input a through Input D Typical bouncing Fig Bouncing the desired part Fig Bouncing the desired part of a song Rhythm guide function Setting the time signature and tempo Using the rhythm guide function Conductor Map On/off selection of the conductor map Tempo Tempo settingSignature Time signature setting Rhythm Guide On/off selection of the rhythm guide Creating the conductor map Setting the signature map 2Bar starts flashing and you can now set the bar number Deleting an unnecessary time signature event Editing a time signature eventAfter deleting Editing the bar offset Default home screen bar offset = -2 barsTo exit the menu mode, press the Stop key Setting the tempo map Tempo = 120bpm, and press After editing Editing a tempo eventDeleting an unnecessary tempo event Before editing Midi synchronization MTC start time Synchronization using MTCConnection Midi sequencer, etc Off Synchronization using Midi clockPage Data export to a personal computer Press the MENU/ENTER knob Procedure of file conversionWAV file conversion Enabling the file conversion Editing a file name Enter a new name using the character entry keysAfter entering a new name, press the MENU/ENTER knob Connection to a personal computer Exporting data to a personal computer Important note Protecting the hard disk 8HD to a computer default setting Exporting data to a personal computer Using the WAV Manager supplied by FostexUsing drag & drop technique Archiving a songPage Press the Stop key Song managementSelect Back on a menu screen and press the MENU/ENTER knob Press the Rewind key Selecting the desired song After entering the name, press the MENU/ENTER knob Editing a song nameCharacter entry keys Delete key 100 Deleting an unnecessary song 101 Protecting a songProtect, then press the MENU/ENTER knob Tips 102 103 Track editingSelect Back on a menu screen and press the MENU/ENTER knob 104 Erasing track data 105 Copying/pasting track data 106 107 Moving track data 108 Exchanging whole track data 109 110 111 Part editing Changing an edit point during editing 112Press the Play key while holding down the Stop key 113 Erasing the parts 114 Copying/pasting the parts-1 115 116 Copying/pasting the parts-2Copying to the clipboard Pasting clipboard data 117 118 119 Moving the parts 120 121 Exchange the parts 122 123 Other functions 124 Hard disk formatting 125 Peak hold time setting 126 Pre-roll/post-roll time setting 127 Beat resolution mode on/off 128 Phantom power on/offTip 129 Initializing the MR-8HD Initialized item Default setting130 131 Troubleshooting Is the recording track in the input monitor mode? Troubles for recording132 Trouble 133 Troubles for playback Is the USB cable connected correctly? Troubles for effectTroubles for USB connection 134 135 Other troublesIs the Rhythm Guide key is illuminated? 136 137 MR-8HD Specifications 138 Specifications 139 Physical dimensions 140 Block diagramWhen using the normal mode When using the bounce mode 1-4 5/6 mode When using the bounce mode 1-8 New Song mode When using the bounce mode 1-6 7/8 mode141 142 Midi Implementation Chart 143 Index 144 Declaration of EC DirectivePage 428387