Honeywell W7750A specifications Direct Access And Special Points

74-2958— 1

106

Table 27. Direct Access And Special Points.

				Digital Stateor Value ofState		E-Vision (M, P,S)			DirectAccess		E-Vision Legend: (M) Monitor, (P) Parameter, (S) Schematic
User Address	NvName	Field Name	(Metric) or States plus Range		Default		Share	Map		Test	Comments
			Engineering Units: English
DestManMode	nviManualMode		MODE_ENABLE	0	MODE_ENABLE		X	X	X		ManualMode is an input which is used to disable the Excel 10s control algorithms
			MODE_DISABLE	1							and to manually set the physical outputs. ManualMode remains unchanged until
			MODE_MANUAL	2							another mode has been commanded or an application restart has been performed.
			SUPPRESS_ALARMS	3							See the Data1.mode for more details.The valid enumerated values are:
			UNSUPPRESS_ALARMS	4							MODE_ENABLE enables the node so that the control algorithm determines the
											operating mode, and controls the physical outputs. MODE_ENABLE is the default
											state after power restore or application restart. If the mode was MANUAL and
											nviManualMode is set to MODE_ENABLE, the node then goes through
											application_restart.MODE_DISABLE sets the node to the DISABLED_MODE. The
											alarm NODE_DISABLED is initiated, all control loops are disabled, and the physical
											outputs are turned off. The physical inputs, network variable inputs, and network
											variable outputs are still functioning when the node is in the DISABLED_MODE.
											MODE_MANUAL sets the node into the MANUAL mode. If MANUAL is selected, the
											controller enters Test Mode (manual override of outputs). The alarm
											NODE_DISABLED is initiated, all control loops are disabled, and the physical
											outputs are controlled manually as commanded by nviManValue. The nodes
											configuration variables and nviManValue are used to set valves, dampers, and / or
											digital output to the desired manual positions or state(s). The physical inputs,
											network variable inputs, and network variable outputs are still functioning when the
											node is in the MANUAL mode.SUPPRESS_ALARMS causes nvoAlarm.type to be
											set to ALARM_NOTIFY_DISABLED, and AlarmLog to no longer record alarms. If
											alarms are suppressed, UNSUPPRESS_ALARMS causes Alarm.type and
											AlarmLog to be returned to reporting alarms. See Alarm for more details. All
											unspecified values are the same as MODE_ENABLE.
TestMode	nviManValue	OutDrive	NORMAL_OP	0	NORMAL_OP						OutDrive ManValue is used for Factory Testing only.
			OUT_1_ON	1
			OUT_2_ON	2
			OUT_3_ON	3
			OUT_4_ON	4
			OUT_5_ON	5
			OUT_6_ON	6
			OUT_7_ON	7
			OUT_8_ON	8
			ALL_OUT_OFF	9
			ALL_OUT_ON	10
			DISABLE_OUT	11
TestHCPos	nviManValue	sbManHeatCoolPosS0	percentage		0					X	During MANUAL mode, ManHeatCoolPos sets the modulating position of the
			-127 to 127								heating or cooling motor (if configured) to the specified position. If ManHeatCoolPos
											is less than 0 or greater than 100, the motor is overdriven for a period longer than
											the motor time to ensure that it is at the end of travel. The heat motor is driven when
											HeatCoolMode is 1 and the cool motor is driven when HeatCoolMode is 0. At the
											moment when the node transfers to MANUAL_MODE or HeatCoolMode is changed,
											ManHeatCoolPos is set the current motor position.
TestEconPos	nviManValue	sbManEconPosS0	Percentage		0					X	During MANUAL mode, ManEconPos sets the modulating position of the
			-127 to 127								economizer motor (if configured) to the specified position. If ManEconPos is less
											than 0 or greater than 100, the motor is overdriven for a period longer than the motor
											time to ensure that it is at the end of travel. At the moment when the node transfers
											to MANUAL_MODE, ManEconPos is set the current motor position.

EXCEL 10 W7750A,B,C CONSTANT VOLUME AHU CONTROLLER