Honeywell W7750A specifications Status Points

Table 23. Status Points.

User Address

NvName

Field Name

(Metric) or States plus Range

DigitalStateor ValueofState

Default

E-Vision(M,P,S)

Share

Map

DirectAccess

HardwareConfig.

ManualConfig.

Test

Comments

E-Vision Legend: (M) Monitor, (P) Parameter, (S) Schematic

Engineering Units: English

nroPgmVer

id[

RTU1

R

A four byte ASCII string indicating the type of node (model).

O

M

nroPgmVer

major_ver

1

R

Software version.

O

M

nroPgmVer

minor_ver

0

R

Software version.

O

M

nroPgmVer

bug_ver

0

R

Software version.

O

M

nroPgmVer

node_type

1

R

The NodeType is a numeric identifier that is stored in EPROM that identifies

O

the Excel 10 node type. Whenever a new software version or upgrade is

M

issued, this is reflected in nroPgmVer which typically is read by a network

81

management node to identify the node type. The contents of nroPgmVer

contain compatible model type information and is fixed at the time when the

node software is compiled.

SrcEmerg

nvoEmerg

EMERG_NORMAL

0

EMERG_NORMAL

M

X

X

Emerg is an emergency output reflecting the state of the locally wired

EMERG_PRESSURIZE

1

smoke detector. If Emerg is EMERG_NORMAL, then no smoke is being

EMERG_DEPRESSURIZE

2

detected by the local sensor or that the smoke detector input is not

EMERG_PURGE

3

configured. If Emerg is EMERG_PURGE, the locally wired smoke sensor is

EMERG_SHUTDOWN

4

indicating a smoke condition.EMERG_PRESSURIZE,

EMERG_NUL

255

EMERG_DEPRESSURIZE, and EMERG_SHUTDOWN are not supported

by Emerg. If Emerg is not configured then it is set to EMERG_NUL

nvoAlarm

subnet

1 to 255

0

subnet is the LONWORKS subnet number (in domain entry 1 of the nodes

domain table) to which the node is assigned.

nvoAlarm

node

0 to 127

0

node is the LONWORKS node number (in domain entry 1 of the nodes

domain table) assigned to the node.

nvoAlarm

type

0 to 255

0

type is the alarm type being issued. When an alarm condition is no longer

TRUE, type is set to the sum of the alarm conditions numeric value and the

RETURN_TO_NORMAL numeric value. The type also is recorded in

AlarmLog. When a new alarm is detected, just the corresponding numeric

value for the alarm is reported. Refer to Table 12 (Excel 10 Alarms) in the

System Engineering Guide for all the error conditions that may be reported.

StatusAlmTyp

nvoAlarmStatus

alarm_bit[0]

FALSE

0

FALSE

X

X

alarm_bit[0]Byte Offset = 0Bit Offset = 0(InputNVFailAlrm)alarm_bit [n]

Byte Offset = 0

TRUE

1

contains a bit for every possible alarm condition. Each alarm type has a

Bit Offset =

corresponding bit in alarm_bit[n] (Alarm.type: 1.24, without

0(InputNVFailAlrm)

RETURN_TO_NORMAL).

nvoAlarmStatus

alarm_bit[0]

FALSE

0

FALSE

alarm_bit[0]

74

Byte Offset = 0

TRUE

1

Byte Offset = 0

Bit Offset = 1

Bit Offset = 1

-

(NodeDisableAlrm)

(NodeDisableAlrm)

2958— 1

EXCEL 10 W7750A,B,C CONSTANT VOLUME AHU CONTROLLER