HP MicroLogix 1761-NET-ENI 75

Connecting 1769-L20 CompactLogix Controllers on Ethernet	7-19

Figure 7.20 ControlLogix 5550 Rung 0 Message Configuration Tab

Figure 7.21 ControlLogix 5550 Rung 0 Message Communication Tab

Publication 1761-UM006A-EN-P - February 2001

Contents

User Manual Important User Information Preface Chapter Product Overview Installation and Wiring Operation E-Mail Messages (Node 50 to 99) Connecting 1769-L20CompactLogix Controllers on Ethernet Troubleshooting Specifications Who Should Use this Manual Purpose of this Manual Common Techniques Used in this Manual Rockwell Automation Support Page Ethernet Connection Non-EthernetDevices Product Overview Hardware Features Default Settings The ENI’s RS-232port has the following default settings: Table 1.1 RS-232Settings Setting Default Operating Modes Device Compatibility Ethernet Networks Page Installation and Wiring European Communities (EC) Directive Compliance Safety Considerations Mounting DIN Rail Mounting Installation Removal Template ENI Port Identification External Power Supply Wiring Ethernet Connections Ethernet Cables Maintain ENI Connections RS-232Port Connections Operation Overview Allocation of Ethernet Connections Operation ENI Functional Overview Program Upload/Download and On-LineSessions Page Host Name RSLogix Page ENI Configuration (Node 248 to 254) Configuration Methods ENI Configuration Utility COM Port Settings RS-232Baud Rate and TCP/IP Parameters Save to ENI RAM or ENI ROM E-MailSettings Message Routing Reset Controller Messaging Configuring ENI Data Parameters Page Configuring ENI String Parameters Page ENI Configuration Parameters Node 248 - Save/Reset Function Node 249 - From String Node 250 - TCP/IP Configuration Subnet Mask Security Mask The security mask acts as a filter on the source IP address such that any mask octet set to the value of 255 becomes “don’t care” octets in the source IP address and all other fields must match exactly The follow examples illustrate the behavior of the security masks: Node 251 - E-MailServer Node 252 - BOOTP Configuration Node 253 - Baud Rate Table 4.7 ENI Baud Rate Options Configuration Value (Integer) Node 254 - Ethernet Hardware Address Peer-to-PeerMessaging Messaging Between the ENI and DF1 Devices Page Message to Configuration Nodes (Nodes 100 to 149) Sending a Message to a Destination Controller (Nodes 0 to 49) Table 5.4 Message Instruction Variables for Sending a Message to a Destination Controller Page E-MailMessages (Node 50 to 99) Overview Configuring E-Mail Destination Addresses Message Text E-Mail E-MailAddress Message Message Fields (to, from, subject) The standard format of the “subject” line is: Sending an E-MailMessage Table 6.1 Message Instruction Variables for Sending an E-MailMessage Connecting 1769-L20CompactLogix Controllers on Ethernet System Diagram Purpose Scope General Ethernet Information Configuring 1761-NET-ENI#1 Page Configuring 1761-NET-ENI#2 Page The 5 rungs used to configure ENI #2 are defined as follows: Table 7.3 ENI #2 Configuration - Rung Descriptions Rung Function BOOTP Rung 4 This rung configures the ENI with its own IP address Page Page Page Page Configure RSLINX and Download The Program To The 1769-L20 Page Create MSG Programs for the SLC 5/05 and the 5550 Controllers Figure 7.15 SLC 5/05 Rung 0 MSG “General” Tab Figure 7.16 SLC 5/05 Rung 0 MSG “Multihop” Tab Page Page Page Page Configuring an Ethernet Driver in RSLINX Page Troubleshooting Network Troubleshooting LED Sequence at Power-Up Troubleshooting Using the LED Indicators Message Instruction Error Codes 15H Local channel configuration parameter error exists 16H Target or Local Bridge address is higher than the maximum node address 17H E6H E7H Target node cannot respond because length requested is too large E8H E9H Page Specifications Physical Specifications Ethernet Specifications MicroLogix Web Site Dimensions BOOTP Configuration Method (default) Using BOOTP Edit the BOOTP Configuration File The boot-serverconfiguration file, BOOTPTAB, is located in the C:\ABIC\BIN directory. BOOTPTAB is an ASCII file that looks like: This file contains the information needed to boot the ENI 1.Open the BOOTPTAB file using a text editor such as Notepad or Wordpad Example BOOTPTAB File Run the Boot Server Utility Running the DOS-BasedUtility DTLBOOTD Running the Windows-BasedUtility Glossary ASA (Advanced System Architecture) Autobaud Auto BCC/CRC Baud Rate Full-duplex IP (Internet Protocol) IP Address NetLinx Services Network PCCC (Programmable Controller Communications Commands) RS-232 Security Mask SMTP (Simple Mail Transfer Protocol) Single-Hop/ Multi-Hop UTP (Unshielded Twisted Pair) The type of cable used in 10BaseT systems Index Allen-Bradley P-3 ASA definition G-1 Fault LED From String 4-11 Full-Duplex definition G-2 Grounding A-1 G-4