Setting
NTSC indicator | PAL indicator |
|
| ||
OPERATE |
|
|
|
| EJECT |
|
|
|
|
| |
|
|
|
|
| MENIU |
Mini | A.DUB |
| REC | PLAY | PAUSE |
|
| DVCAM NTSC PAL | REC INH. |
|
|
PROFESSIONAL |
|
|
|
| |
MIC REMOTE SEL. | INPUT SEL. | REW | STOP | SET | |
FF | |||||
SERIAL | LINE |
|
|
| |
9PIN WIRELESS | DV Y/C |
|
|
| |
|
|
|
|
| |
INPUT SEL. switch
Rear panel
DIO CH 2/4 LINE VIDEO | Y/C |
IN |
|
|
| REMOTE | DC12V |
|
| |
OUT |
| NTSC/PAL |
|
| |
9PIN |
| SERIAL NTSC PAL |
NTSC/PAL switch
Memo
•For DV signal input, the sig- nal system (NTSC/PAL) is identified automatically.
•For DV signal input, the AU- DIO MODE item cannot be set. It will be the same mode as that of the input signal. (48K or 32K)
AUDIO/VIDEO menu
– – – A U D I O V I D E O – – –
A U D I O MO D E | 4 8 K |
A O U T A T S E A R C H | O N |
A U D I O O U T S E L | C H - 1 / 2 |
A U D I O O U T L E V E L | N O RM |
S E T U P ( N T S C ) | O F F |
P A G E B A C K |
|
SYSTEM (1/2) menu
| – – – S Y S T E M [ 1 / 2 ] – – – | |
S T L / F . A D V | 2 N D | |
B A C K U P R E C T I M E | O F F | |
L O N G | P A U S E T I M E | 5 M I N |
L O N G | P A U S E MO D E | F . A D V |
I N D E X WR I T E | O N | |
R E P E A T MO D E | B L A N K | |
N E X T | P A G E |
|
P A G E | B A C K |
|
Setting the signal system (NTSC/PAL)
The signal system for analogue input is set with the NTSC/PAL switch located at the rear panel. Either the NTSC or the PAL indica- tor on the front lights up, depending on the setting.
*Before setting the NTSC/PAL switch, please set the unit to the OPERATE OFF mode.
Selecting the video input signal
Please use the INPUT SEL. switch on the front panel.
Y/C : Input Y/C separate video signals.
LINE: Input composite video signals.
DV : Input DV signals.
Setting the AUDIO/VIDEO menu (☞ Page 61)
• AUDIO MODE
Use this menu item to set the audio sampling frequency for recording. 32K : Perform recording with an audio sampling frequency of 32kHz.
Use this setting when performing audio dubbing on CH3 and CH4.
48K : Perform recording with an audio sampling frequency of 48kHz. Audio dubbing is not available.
•SET UP (NTSC only)
Set this item to enable/disable setup to composite signals or Y/C separate video during recording.
Setting the SYSTEM menu (☞ Page 57)
•LONG PAUSE TIME
Sets the time period, after the lapse of which the unit will enter the tape protection mode when pause is activated for an extended pe- riod of time.
•INDEX WRITE
This setting turns on/off automatic recording of index signals when recording begins.
Setting the time code recording during DV signal input
Set the TC DUPLICATE item of the TIME CODE menu to determine whether to use the time code from the built in time code generator and clock or the data from the DV terminal. (☞ Page 62)