JVC GY-HD250, GY-HD251 manual Warnings and Responses, Display, Status, Action, Others, Memo

e_hd250.book Page 106 Tuesday, October 24, 2006 3:11 PM

OTHERS

Warnings and Responses

Warnings are displayed on the LCD monitor or the viewfinder if there was a mistaken operation, if the battery or tape is low, or if there is a problem on the VTR.

In addition, if the tape or battery is low or the VTR has a problem, the tally lamp flashes (or lights) and an alarm is output from the monitor speaker or PHONES jack.

MEMO

GY-HD250/GY-HD251 uses microcomputers. It may not operate properly if there is external static or interference. If this hap- pens, turn the power off and then on again.

Display	Status	Action
60/30 INHIBIT	The FRAME RATE item is set to 50/25 or 24, and a tape re-	Sets the FRAME RATE item on the VIDEO FORMAT menu
CHANGE FRAME	corded in 60/30 frame is played back or it is input into the	screen to match the frames.
RATE MENU	IEEE1394 port in VTR mode.	X See page 77.
50/25 INHIBIT	The FRAME RATE item is set to 60/30 or 24, and a tape re-
CHANGE FRAME	corded in 50/25 frame or it is input into the IEEE1394 port
RATE MENU	in VTR mode.
24 INHIBIT CHANGE	The FRAME RATE item is set to 50/25 or 60/30, and a tape
FRAME RATE MENU	recorded in 24 frame is played back or it is input into the
	IEEE1394 port in VTR mode.
AUX IN INHIBIT	• U model	Set the FRAME RATE item as shown below to input exter-
CHANGE	Displays when the FRAME RATE item is set to 50/25 or	nal images.
FRAME RATE MENU	24 and the GENLOCK/AUX IN switch is set to AUX IN.	U model : 60/30
	• E model	E model : 50/25
	Displays when the FRAME RATE item is set to 60/30 or
	24 and the GENLOCK/AUX IN switch is set to AUX IN.
SYNC LOCKING	• Camera image is locking to external synchronization sig-	It is not possible to enter recording mode while “SYNC
	nals.	LOCKING” is displayed. Wait until the indication disap-
		pears.
PLEASE WAIT	Displays when external synchronization signal is input and
	REC trigger button is pressed while SYNC LOCKING is dis-
	played.
INVALID SYNC	• Displays when the FRAME RATE item is set to 60/30 or	Input supported external synchronization signals.
	24 and signals not supported by GENLOCK are input.	X See page 66.
	• Displays when the FRAME RATE item is set to 50/25 and
	signals not supported by GENLOCK are input.
DV-60I INVALID!	A tape recorded in DV-60I, DV-24P, or DV-24PA format	The E model cannot play back tapes recorded in DV-60I,
DV-24P INVALID!	was played back or input into the IEEE1394 connector in	DV-24P or DV-24PA format or input into the IEEE1394 con-
DV-24PA INVALID!	VTR mode on the E model.	nector in VTR mode.
DV-50I INVALID!	A tape recorded in DV-50I or DV-25P format was played	The U model cannot play back tapes recorded in DV-50I or
DV-25P INVALID!	back or input into the IEEE1394 connector in VTR mode on	DV-25P format or input into the IEEE1394 connector in
	the U model.	VTR mode.
HDV-SD60P	A tape recorded in HDV-SD60P format was played back or	GY-HD250/GY-HD251 cannot play back or input an HDV-
INVALID!	input into IEEE1394 connector in VTR mode.	SD60P/HDV-SD50P signal.
HDV-SD50P	A tape recorded in HDV-SD50P format was played back or
INVALID!	input into IEEE1394 connector in VTR mode.
INVALID TAPE!	A computer data tape or a DVC PRO cassette was used.	Use a MiniDV videocassette.
LP TAPE INVALID!*	Tried to play back a tape recorded in LP mode.	GY-HD250/GY-HD251 cannot record or play back in LP
		mode.
NO DV SIGNAL*	DV signal was not input.	Set the IEEE1394 switch to DV and input a DV signal.
NO HDV SIGNAL*	HDV signal was not input.	Set the IEEE1394 switch to HDV and input an HDV signal.
COPY INHIBIT*	Tried to record a copyguarded signal.	Cannot record a copyguarded signal.
REC INHIBIT*	A tape that cannot be recorded (back switch is set to SAVE)	Set the switch on the back of the cassette tape to REC.
	was inserted.
NO TAPE*	No videocassette tape is inserted.	Insert a cassette tape.

106