TDR6 Remote Command Listing (continued)
Mnemonics | Parameters/ | DVB Defaults |
| Description |
Response Values |
| |||
|
|
|
| |
|
|
|
|
|
BISS MODE | none, mode1, modee | none |
| Sets the BISS mode used to descramble the incoming |
|
|
|
| transport stream. |
|
|
|
| Note: Before setting this command to mode1 or modeE, the |
|
|
|
| appropriate KEY and ID values must first be entered. |
|
|
|
| Note: There may be a slight delay in picture when setting or |
|
|
|
| changing BISS modes. This is due to the routing of the |
|
|
|
| signal to the descrambling chip. |
|
|
|
| Note: To ensure proper BISS operations, ensure that PGCA |
|
|
|
| is set to Off. |
|
|
|
|
|
BISS STATUS | scrambled, | — |
| |
| not_scrambled |
|
| stream: |
|
|
|
| ■ Scrambled: the incoming transport stream is scrambled |
|
|
|
| ■ Not_scrambled: the incoming transport stream is not |
|
|
|
| scrambled |
|
|
|
|
|
DC | — | — |
| When DC is entered, the TDR6 returns the following |
|
|
|
| decompressor information: PSI enable, program number, |
|
|
|
| clock recover, PCR PID, lock transport, PCR filter, and peak |
|
|
|
| PCR jitter. |
|
|
|
| Front panel equivalent: None |
|
|
|
|
|
DC AUTOSEL | On, Off | On |
| Sets how PIDs are selected: |
|
|
|
| ■ On: TDR6 selects the lowest incoming program |
|
|
|
| ■ Off: Operator must enter the program manually |
|
|
|
| Front panel equivalent: Details>Service>Auto Select |
|
|
|
|
|
DC FILTER | Normal, ATM | Normal |
| Sets the PCR (program clock reference) filter for normal |
|
|
|
| operations or operations over an ATM network. |
|
|
|
| ■ Normal: set for normal operations |
|
|
|
| ■ ATM: set for operations over an ATM network |
|
|
|
| Front panel equivalent: Details>input>Config>Filter>PCR |
|
|
|
| Filter |
|
|
|
|
|
DC INPUT | ASI, RF_A, RF_B, | ASI |
| Selects input source. |
| RF_C, RF_D |
|
| ■ ASI: selects an external demodulator as input source |
|
|
|
| ■ RF_A: selects RF input as the transport stream source |
|
|
|
| and LNB 1 as active port |
|
|
|
| ■ RF_B: selects RF input as the transport stream source |
|
|
|
| and LNB 2 as active port |
|
|
|
| ■ RF_C: selects RF input as the transport stream source |
|
|
|
| and LNB 3 as active port |
|
|
|
| ■ RF_D: selects RF input as the transport stream source |
|
|
|
| and LNB 4 as active port |
|
|
|
| Front panel equivalent: Details>Input>Config>Select>Input |
|
|
|
|
|
DC JITTER | 0 to 3500000 ns | — |
| |
|
|
|
| STC and PCR clocks. |
|
|
|
| Front panel equivalent: Details>Input>Status>Peak Jitter |
|
|
|
|
|
DC LOCK TRANSPORT | Locked, Unlocked | — |
| |
|
|
|
| Front panel equivalent: Details>Input>Status>Transport |
|
|
|
|
|
DC PCR PID | — | — |
| |
|
|
|
| which is automatically selected by the TDR6. |
|
|
|
| Front panel equivalent: None |
|
|
|
|
|
DC PROG | <number> | 1 |
| Selects or displays the service. |
|
|
|
| When queried, the response contains the number, the |
|
|
|
| service number and the name, if any. For example: DC |
|
|
|
| PROG 1,Service 1,Unnamed |
|
|
|
| When no services are present, the system returns the |
|
|
|
| message no services available. |
|
|
|
| Front panel equivalent: Details>Service |
|
|
|
|
|
Using a Remote Unit |
| 39 |
