Kodak 500 Bar Code Test Option 3Read Rate

A-61408 September 1995 C-19

This display gives the first 15 characters (including the *

representing the start character) of the decoded values.

Press the Stop key, wait approximately 2 seconds, then press

the Enter key to proceed to the next page of the decoded

values. The format of the display is the same until the remain-

ing number of characters becomes equal to or less than 15.

B C T Y P E = C O D E 3 9

X X X X X X X X

This display gives the final page of the decoded values. In

order to return to the first page of the decoded values, press

the Enter key. This will allow you to circle through the data.

NOTE: For multiple bar codes on a single document, the

asterisk (*) denotes the start of each bar code data,

but the asterisk can also be displayed within the data

if for some reason a character cannot be read.

2. Upon completion of the test, press the Stop or End key to

return to the menu page of Function 65. Press the Stop key

one more time to return to normal operation.

Bar Code Test Option 3–Read Rate This option provides the read rate (percentage of bar codes

properly read).

1. Feed 100 test documents into the transport system. Until the

number of the fed documents is equal to 100, the following

message will appear on the Status Display, where XXX is the

present number of documents fed:

B C T Y P E = C O D E 3 9

D o c C o u n t = X X X

2. When 100 documents have been fed or when the Stop key

has been pressed, the following message will appear in the

Status Display, where "@ YYY" denotes the number of

documents that have been fed:

B C T Y P E = C O D E 3 9

R a t e = X X X % (@ Y Y Y)

The percentage indicates the read rate of the documents just

processed.

When using Kodak Bar Code Standard Test Documents

which are provided by Parts Services, if the read rate is

significantly lower than that in the past, this indicates that any

reduction in the overall read rate can be caused by a defi-

ciency in the equipment. Perform required maintenance and

rerun the test. If the results of the second test are similar to

the first, contact service.

Contents

Main Page Table of Contents Page 1 Introduction Scanner Features 1-2 A-61408 September 1995 Scanner Overview Scanner 500 Front Views Kodak Imagelink Page Page A-61408 September 1995 1-5 Control Panel Two-line Status Display Status Display Enab l e d M O DE 1 ABC/ 2 91 . 25. Operation Keys/Indicators 0 F Front 456 123+ /// // / Page Page 2 Getting Started Kodak Imagelink Enabled Scanner Operation Overview Power-up Process Calibrating the Scanner Unsuccessful Calibration Adjusting the Feed Roller and Separator Roller Page Page Adjusting the Self-Centering Feed Shelf Adjusting the Exit Hopper Page 3 Operating the Scanner Scanning Process Function Codes Using Function Codes Function Code Summary Function Code Listing Page Page Page Page Page Setting Image Levels Setting Application Modes Preparing Documents Document Sizes Kodak Imagelink Document Orientation Scanning Documents Automatic Feed Method Manual Feed Method 4 Error Messages User Actions System Administrator Actions Controlled Power-down Se- quence Controlled Power-down Sequence A-61408 September 1995 4-3 Message Listings Error Code Description Action Adjusting the Feed Roller and Separator Roller A-61408 September 1995 4-5 4-6 A-61408 September 1995 Error Code Description Action Error Code Description Action 5 Scanner Maintenance Cleaning Materials Do NOT use industrial cleaning solvents in any of the cleaning procedures. Daily (or as required) Cleaning the Imaging Guides Page Page Page Weekly (or as required) Cleaning the Feed Roller and Separator Roller Page Page Page Page Page Changing the Lamps Zum Auswechsein Der Lampen WARNING: Calibrating the Scanner. 6 Troubleshooting Clearing the Document Path Document Path Removing Documents Clearing a Jam in Area A Clearing a Jam in Area B Page Page Clearing a Jam in Area C Clearing a Jam in Area D Removing Non-Jammed Documents Appendix A Footswitch 500 Function Codes Page Appendix B Patch Reader 500 Available Patches Patch Location on Documents Printing Patches Changing the Horizontal Read Position Cleaning the Patch Reader Do not remove the Cable Tie from the Patch Reader. Function Codes Performing a Patch Test. Performing the Patch Test Function (Future Function) Appendix C Bar Code Reader 500 Use of Bar Code Information Bar Code Types Printing Bar Codes on Documents Bar Code Specifi- cations Bar Code Made Easy Function Codes Performing a Bar Code Test. Performing a Bar Code T est only when the bar code reader is installed and enabled. Kodak Bar Code Standard Test Documents. customer applica- tion documents. Bar Code Test Option 1 Evaluate Page Page Page Section 5, Scanner Maintenance B C T Y P E = C O D E 3 9 <PARTIAL> M O D = X X X % D E F = X X X % G r a d e = X R e m o v e D o c , C l o s e D o o r , P r e s s E n t e r Page Page Page Fields Displayed Bar Code Specifications Dimensional Field Values Low Bar Code Ratings Bar Code Specifi- cations Bar Code Test Option 2 Display Bar Code Test Option 3Read Rate Bar Code Specifications Page Page Appendix D Document Printer 500 Information Printed Appearance of Printed Information Page Page Page A-61408 September 1995 D-5 Hardware carriage and a Rear Document Printer 500 carriage. D-6 A-61408 September 1995 Rear Document Printer Mounting Plate Function Codes Performing the Print T est Function Cleaning and Priming the Ink Cartridge Ink deposits or spills can occur if you are not careful during the priming procedure. Front Document Printer Page Page Rear Document Printer Page Replacing the Ink Cartridge Page Page Glossary