Kodak 500 - page 97

A-61408 September 1995 D-3

Changing the Vertical Start Print Position

Function Code F46 can be used to change the vertical start print

position of the Front Document Printer. Function Code F47 can be

used to change the Vertical Start Print Position of the Rear

Document Printer.

To change the vertical start print position:

1. Press the F key.

2. Press the numeric keys that correspond to these functions

(4 and then 6, or 4 and then 7).

3. Press Enter.

4. Press the numeric keys that correspond to a value between

0.125 inches (3 mm) and 30 inches (760 mm) in increments

of 0.125 inches (3 mm).

NOTE: The value should not exceed the document length.

5. Press Enter.

Changing the Horizontal Print Position

The horizontal print position of the Front Document Printer is

manually set in one of twelve positions on the Front Document

Printer Mounting Plate. The horizontal print position of the Rear

Document Printer is manually set in one of six positions on the

Rear Document Printer Mounting Plate.

NOTE: The twelve front print positions are indicated with F1–F12,

and the six rear print positions are indicated with R1–R6

on the label on the Feed Tray.

A3

A4

F1 R1 F2 F3 R2 F4 F5 R3 F6 F7 R4 F8 F9 R5 F10 F11 R6 F12

To change the horizontal print position:

1. Set the printer into one of the twelve printer positions so that

the notched tab fits into the notched gap on the Document

Printer Mounting Plate.

NOTE: The Front Document Printer is secured to the mount-

ing plate by magnets. The Rear Document Printer is

secured to the mounting plate with the same magnets

and two spring clips. To remove the Rear Document

Printer, compress the two spring clips and lift the

printer out of the Rear Document Printer Mounting

Plate.

CAUTION: For safety reasons the movement of the Lower

Access Door is intentionally slowed with a two-

way rotary damper. Open and close the door

slowly.

Contents

Main Page Table of Contents Page 1 Introduction Scanner Features 1-2 A-61408 September 1995 Scanner Overview Scanner 500 Front Views Kodak Imagelink Page Page A-61408 September 1995 1-5 Control Panel Two-line Status Display Status Display Enab l e d M O DE 1 ABC/ 2 91 . 25. Operation Keys/Indicators 0 F Front 456 123+ /// // / Page Page 2 Getting Started Kodak Imagelink Enabled Scanner Operation Overview Power-up Process Calibrating the Scanner Unsuccessful Calibration Adjusting the Feed Roller and Separator Roller Page Page Adjusting the Self-Centering Feed Shelf Adjusting the Exit Hopper Page 3 Operating the Scanner Scanning Process Function Codes Using Function Codes Function Code Summary Function Code Listing Page Page Page Page Page Setting Image Levels Setting Application Modes Preparing Documents Document Sizes Kodak Imagelink Document Orientation Scanning Documents Automatic Feed Method Manual Feed Method 4 Error Messages User Actions System Administrator Actions Controlled Power-down Se- quence Controlled Power-down Sequence A-61408 September 1995 4-3 Message Listings Error Code Description Action Adjusting the Feed Roller and Separator Roller A-61408 September 1995 4-5 4-6 A-61408 September 1995 Error Code Description Action Error Code Description Action 5 Scanner Maintenance Cleaning Materials Do NOT use industrial cleaning solvents in any of the cleaning procedures. Daily (or as required) Cleaning the Imaging Guides Page Page Page Weekly (or as required) Cleaning the Feed Roller and Separator Roller Page Page Page Page Page Changing the Lamps Zum Auswechsein Der Lampen WARNING: Calibrating the Scanner. 6 Troubleshooting Clearing the Document Path Document Path Removing Documents Clearing a Jam in Area A Clearing a Jam in Area B Page Page Clearing a Jam in Area C Clearing a Jam in Area D Removing Non-Jammed Documents Appendix A Footswitch 500 Function Codes Page Appendix B Patch Reader 500 Available Patches Patch Location on Documents Printing Patches Changing the Horizontal Read Position Cleaning the Patch Reader Do not remove the Cable Tie from the Patch Reader. Function Codes Performing a Patch Test. Performing the Patch Test Function (Future Function) Appendix C Bar Code Reader 500 Use of Bar Code Information Bar Code Types Printing Bar Codes on Documents Bar Code Specifi- cations Bar Code Made Easy Function Codes Performing a Bar Code Test. Performing a Bar Code T est only when the bar code reader is installed and enabled. Kodak Bar Code Standard Test Documents. customer applica- tion documents. Bar Code Test Option 1 Evaluate Page Page Page Section 5, Scanner Maintenance B C T Y P E = C O D E 3 9 <PARTIAL> M O D = X X X % D E F = X X X % G r a d e = X R e m o v e D o c , C l o s e D o o r , P r e s s E n t e r Page Page Page Fields Displayed Bar Code Specifications Dimensional Field Values Low Bar Code Ratings Bar Code Specifi- cations Bar Code Test Option 2 Display Bar Code Test Option 3Read Rate Bar Code Specifications Page Page Appendix D Document Printer 500 Information Printed Appearance of Printed Information Page Page Page A-61408 September 1995 D-5 Hardware carriage and a Rear Document Printer 500 carriage. D-6 A-61408 September 1995 Rear Document Printer Mounting Plate Function Codes Performing the Print T est Function Cleaning and Priming the Ink Cartridge Ink deposits or spills can occur if you are not careful during the priming procedure. Front Document Printer Page Page Rear Document Printer Page Replacing the Ink Cartridge Page Page Glossary