5. Specify time-varying change in the tone

Use EG 1 to create time-varying change in the cutoff fre- quency (FILTER “Cutoff”).

If you wish to use the front panel knobs to adjust the EG 1 parameters, use the SEQ EDIT [SELECT] key to make the SEQ 1–3 LED’s go off.

Note onNote off

 

 

 

 

 

 

 

c

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cutoff

 

 

 

 

 

 

 

 

 

 

 

 

 

 

a

 

b

 

 

 

d

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Time

 

 

 

 

 

 

 

 

 

 

 

 

 

a: Attack Time

 

c: Sustain Level

 

b: Decay Time

 

d: Release Time

a b c d

a. Adjust the speed at which the tone will change dur- ing the attack

Rotate the EG 1 [ATTACK] knob.

The LCD screen will show Page 10A: EG 1 “Attack.” Rotating the knob toward the right will cause the tone to change more slowly, and rotating it toward the left will cause the tone to change instantly.

10A EG 1

Attack: 000

If rotating the knob does not produce an effect, try adjusting the FILTER [EG 1 INT] knob, or make sure that the SEQ EDIT SEQ 1–3 LED’s are dark. If these LED’s are lit, it is not possible to edit the EG or LFO. The knobs will function to edit the sequence data.

b. Adjust the speed at which the tone will change dur- ing the decay

Rotate the EG 1 [DECAY] knob.

The LCD screen will show Page 10B: EG 1 “Decay.” Rotating the knob toward the right (increasing the value) will cause a longer decay time until the sustain level is reached.

10B EG 1

Decay: 030

d. Adjust the speed at which the tone will change after the note is released

Rotate the EG 1 [RELEASE] knob.

The LCD screen will show Page 10D: EG 1 “Release.” Rotating the knob toward the right will make the sound change more slowly, and rotating it toward the left will make it change instantly.

10D EG1

Release: 000

6. Adjust the output of the timbre

a

b

c

d

a. Adjust the volume of the timbre

Rotate the [LEVEL] knob.

The LCD screen will show Page 09A: AMP “Level.” If the volume changes over time, this level will be the maximum level that occurs during the change in vol- ume.

09A AMP

Level: 127

b. Adjust the output panpot (stereo position)

Rotate the [PAN] knob.

The LCD screen will show Page 09B: AMP “Panpot.” When the knob is in the center (CNT), the output will be centered.

09B AMP

Panpot: CNT

c. Adjust the brightness of the sustained sound

Rotate the EG 1 [SUSTAIN] knob.

The LCD screen will show Page 10C: EG 1 “Sustain.” The change in brightness produced by the [SUSTAIN] knob will depend on the setting of the [EG 1 INT] knob.

10C EG 1

Sustain: 060

c. Select the envelope source for the volume

Press the [EG 2 /GATE] key.

Each time you press the key, the envelope source will change.

If you want the volume change over time, select EG 2 ([EG 2/GATE] key LED dark).

If you want the volume to sound at a fixed level, as on an organ, select GATE ([EG 2/GATE] key LED lit).

22

Page 28
Image 28
Korg MS2000R manual Specify time-varying change in the tone, Adjust the output of the timbre