Editing Global parameters, Basic editing procedure

Editing Global parameters

In Global mode you can make settings that affect the entire MS2000/MS2000R, and also create user scales.

Basic editing procedure

a. Enter Global mode

●Press the [GLOBAL] key.

You will enter Global mode. The upper line of the LCD screen will show the page number and page name, and the lower line will show the parameter name and parameter value.

Page number Page name

1A GLOBAL

Mst.Tune:440.0Hz

Parameter name Parameter value

b. Select a page

In the same way as in LCD Edit mode, use the PAGE [+][–] keys and SELECT [1]–[16] keys to select the desired page.

The SELECT [1]–[16] keys correspond to pages as shown below.

Key	Page

SELECT [1]	Page1A: GLOBAL “Mst.Tune”

SELECT [2]	Page1D: GLOBAL “Vel.Curve”

SELECT [3]	Page1F: GLOBAL “AudioInThru”

SELECT [4]	Page2A: MEMORY “Protect”

SELECT [5]	Page3A: MIDI “MIDI Ch”

SELECT [6]	Page3C: MIDI “Clock”

SELECT [7]	Page3D: MIDI “MIDI1”

SELECT [8]	Page3F: MIDI “MIDI Dump”

SELECT [9]	Page4A: MIDI FILTER “ProgChg”

SELECT [10]	Page4B: MIDI FILTER “CtrlChg”

SELECT [11]	Page4C: MIDI FILTER “P.Bend”

SELECT [12]	Page4D: MIDI FILTER “SystemEx”

SELECT [13]	Page6A: PEDAL&SW “A.Pedal”

SELECT [14]	Page6B: PEDAL&SW “A.SwFunc”

SELECT [15]	Page7A: USERSCALE “Key: Detune”

SELECT [16]	Page8A: CALIB (AS)

c. Select a parameter

As in LCD Edit mode, use the CURSOR[√][®] keys to select the desired parameter. (☞p.19)

d. Input the value

●Use the [+/YES] [–/NO] keys to input the value. When you press the [+/YES] [–/NO] keys, the value will increase or decrease in steps of one.

If you hold down the [+/YES] key and press the [–/NO] key, the value will increase in steps of ten.

If you hold down the [–/NO] key and press the [+/YES] key, the value will decrease in steps of ten.

e. Write (save) the Global parameters

Global parameters that you edit will revert to their unedited state if you turn off the power without saving. If you wish to save your settings, you must perform the Write operation.

To write Global parameters, press the [WRITE] key in Glo- bal mode.

The LCD screen will ask you for conﬁrmation. If you wish to write the data, press the [WRITE] key once again. To can- cel the Write operation, press the [EXIT] key in the conﬁr- mation screen.

Global parameters can be saved regardless of the mem- ory protect setting (Global mode Page 2A: MEMORY “Protect”).

Never turn off the power during the Write operation. This can damage the data.

Editing parameters

1. Defeat memory protect

To prevent data from being rewritten accidentally, the MS2000/MS2000R provides a memory protect function that disables writing to memory. In order to write edited data, you must ﬁrst turn memory protect OFF (so that writ- ing will not be disabled).

1Press the [GLOBAL] key. You will enter Global mode.

2Press the SELECT [4] key.

The LCD screen will show Page 2A: MEMORY “Pro- tect.”

2A MEMORY

Protect:ON

3Press the [–/NO] to turn “Protect” OFF.

2A MEMORY

Protect:OFF

Now it will be possible to execute the write operation.

2. Restoring settings to their factory state

The factory settings are called the “preloaded data.” You can load this preloaded data to restore the MS2000/MS2000R’s programs and global settings to the factory state.

When you load this data, all data in the MS2000/ MS2000R will be rewritten to the factory settings. Before you perform this operation, make sure that it is OK to overwrite the data.

If Global mode Page 2A: MEMORY “Protect” is ON, the preload data cannot be loaded. If you wish to load the preload data, you must ﬁrst turn “Protect” OFF.