Basic Guide | Korg MS2000R specification

Basic Guide

Basic Guide

Introduction

Front and rear panel

Connections

Playing

Editing

Introduction

Front and rear panel

Connections

Playing

Editing

Image 7

Korg MS2000R manual Basic Guide

Contents

Page FCC Regulation Warning for U.S.A Power supplyLocation Interference with other electrical devices Iii About this manualHow this manual is organized Printing conventions in this manual Table of Contents Parameter Guide About Midi How Resolution and Sync Note values correspond Basic Guide Basic Guide Structure MS2000/MS2000R Main featuresModes EG1/2 How a program is structuredSynth programs OSC1/OSC2/NOISE OSC1/NOISE/AUDIO in 1 jack carrier Vocoder programsAudio in 2 jack modulator MS2000 MS2000R Front panel Control 1 knob POWER/VOLUME knobKnob Wave key LCD Original Value LEDLCD Edit and Global modes, this will display parameters Select 1-16 keys Rear panelPhones jack MS2000R Modulation wheel Control panel MS2000Cable hook Pitch Bend wheel Connecting Midi devices Connecting the AC adapterConnecting external devices Connecting pedals and switches Connections to a computer/ sequencer Setting the Midi channel preparations for playingConnecting the MS2000 to a computer/ sequencer Connecting the MS2000R to a com- puter/sequencer Listen to the demo perfor- mance MS2000 Playing a programSelect a program Changing the pitch sounded by the keys in one-octave steps Using the BANK/OCTAVE UP Down keys and the Select 1-16 keysSelecting a program Use the Select 1-16 keys to play the program Playing arpeggios Using the knobs and keys to modify the settingsPlay a program in which the arpeggia- tor is turned on Checking the value recorded for each step Using MOD Sequence to modify the soundPlaying a program in which MOD Sequence is on Checking the parameter that is assigned to each sequence Using an external waveform as the carrier Using external inputUsing the vocoder function Using an internal waveform as the carrier Editing program parameters Basic editing proceduresEditing in Program Play mode Editing in LCD Edit mode Writing saving an edited program Switching timbresReturning to the state before editing Compare Editing a synth program Make oscillator settingsSpecify how notes will be sounded Set the volume of each oscillator Make ﬁlter settings Specify time-varying change in the tone Adjust the output of the timbre Specify time-variant changes in volume Apply modulation to parameters Virtual Patch Make LFO settings Set SEQ Common parameters Make MOD Sequence settingsSpecify sequence data for each step Editing effect parameters Modulation effect settings Editing arpeggio parameters Delay settings Editing vocoder program Adjust the mic input audioSet the ﬁlter Changing the program name Editing parameters Basic editing procedureRestoring settings to their factory state Editing Global parameters Saving data on an external device Data Dump Synchronization with external Midi devicesSynchronizing an external Midi device to the MS2000/MS2000R Screen will ask you to conﬁrm the data transmis- sion Program parameters Global parameters Parameter Guide +3, 2+2, 3+1 Page01 Common GLB VoicePage02 Name Page03 Voice Page05 OSC PitchOscillator Page04 Pitch Dwgs OFF MixerPage06 OSC Page07 Mixer Page08 Filter Filter Page10 EG Page11 EG AMP AmpliﬁerEG Envelope Generator Page09 AMP Page12 LFO Page13 LFO LFO Low Frequency Oscillator32...1/1 Page18 SEQ Common Virtual PatchMOD Sequence Page14 PATCH1 Page15 PATCH2 Page16 PATCH3 Page17 PATCH4 Page20 SEQ2 Page19 SEQ1Page21 SEQ3 Page24 EQ Page23 Delay FXEffects Page22 MOD FX Page25 Arpeggio Arpeggiator Page26 Utility Utility InitSeq SwapTimbreCopySeq SwapSeq CopySeqAllSwap Seq Threshold  000...127 AudioPage06 Audio Wave  Saw...Audio Control1  000 127 Control2  AMP CH Param Init ch Pan Init ch Lvl Const Page1 Global430.0Hz...450.0Hz 001...127 Preload Page2 Memory Page3 MidiInternal...Auto Chg Page4 Midi FilterA00...H16 Page6 PEDAL&SW Page5 Ctrl Change Page8 Calib Page7 User Scale Aftertouch About MidiMidi channels Program change Control changes Bn, cc Control changes Controlling the arpeggiator Parameters transmitted and received via NrpnGate values Controlling the FC MOD source of a vocoder program Filter Other controlsControlling the Virtual Patch 1-4 Source Controlling the Virtual Patch 1-4 Destination SEQ2/CH PAN System exclusive messages Transmitting sound settings etc. Data Dump Wave CC#77 Front panel knob/key control change assignments OSC 2 Semitone values Control 2 values when OSC 1 Wave = Dwgs SEQ Arpeggiator Voice Name List D01 Ana Fuzz Synth Hard Single G01 Square Comp Synth Hard Single Program No Program Name Blank chart Timbre2 Dual/Split Vocoder Program Speciﬁcations and options Troubleshooting Index Symbols Latch Delay FX LFO Midi Implementation Chart