Korg MS2000R specs

4Use the [+/YES] [–/NO] keys to specify the data that will be transmitted.

3F MIDI

ALL OK?

If 1PROG is selected, only the data of the currently selected program will be transmitted.

If PROG is selected, all program data will be transmit- ted.

If GLOBAL is selected, Global data will be transmitted.

If ALL is selected, all programs and Global data will be transmitted.

5Press the CURSOR [®] key to move the cursor to OK?

6Press the [+/YES] key.

The screen will ask you to conﬁrm the data transmis- sion.

3F MIDI

Are You Sure OK?

7Press the [+/YES] key.

The data will be transmitted.

ALL DATA

Processing...

When the transmission is completed, the display will indicate “Completed...”

Please do not touch the knobs, keys, keyboard, or wheels etc. of the MS2000/MS2000R while the data is being transmitted.

If you wish to receive a data dump on the MS2000/ MS2000R, you must ﬁrst turn Global mode Page 2A: MEMORY “Protect” OFF. If “Protect” is ON, data dumps cannot be received.

32

Image 38

Korg MS2000R manual Screen will ask you to conﬁrm the data transmis- sion

Contents

Page Interference with other electrical devices Power supplyLocation FCC Regulation Warning for U.S.A Printing conventions in this manual About this manualHow this manual is organized Iii Table of Contents Parameter Guide How Resolution and Sync Note values correspond About Midi Basic Guide Basic Guide Modes Main featuresStructure MS2000/MS2000R OSC1/OSC2/NOISE How a program is structuredSynth programs EG1/2 Audio in 2 jack modulator Vocoder programsOSC1/NOISE/AUDIO in 1 jack carrier Front panel MS2000 MS2000R Wave key POWER/VOLUME knobKnob Control 1 knob LCD Edit and Global modes, this will display parameters Original Value LEDLCD Phones jack MS2000R Rear panelSelect 1-16 keys Pitch Bend wheel Control panel MS2000Cable hook Modulation wheel Connecting pedals and switches Connecting the AC adapterConnecting external devices Connecting Midi devices Connecting the MS2000R to a com- puter/sequencer Setting the Midi channel preparations for playingConnecting the MS2000 to a computer/ sequencer Connections to a computer/ sequencer Listen to the demo perfor- mance Select a program Playing a programMS2000 Use the Select 1-16 keys to play the program Using the BANK/OCTAVE UP Down keys and the Select 1-16 keysSelecting a program Changing the pitch sounded by the keys in one-octave steps Play a program in which the arpeggia- tor is turned on Using the knobs and keys to modify the settingsPlaying arpeggios Checking the parameter that is assigned to each sequence Using MOD Sequence to modify the soundPlaying a program in which MOD Sequence is on Checking the value recorded for each step Using an internal waveform as the carrier Using external inputUsing the vocoder function Using an external waveform as the carrier Editing in LCD Edit mode Basic editing proceduresEditing in Program Play mode Editing program parameters Compare Switching timbresReturning to the state before editing Writing saving an edited program Specify how notes will be sounded Make oscillator settingsEditing a synth program Set the volume of each oscillator Make ﬁlter settings Adjust the output of the timbre Specify time-varying change in the tone Specify time-variant changes in volume Make LFO settings Apply modulation to parameters Virtual Patch Specify sequence data for each step Make MOD Sequence settingsSet SEQ Common parameters Modulation effect settings Editing effect parameters Delay settings Editing arpeggio parameters Set the ﬁlter Adjust the mic input audioEditing vocoder program Changing the program name Editing Global parameters Basic editing procedureRestoring settings to their factory state Editing parameters Synchronizing an external Midi device to the MS2000/MS2000R Synchronization with external Midi devicesSaving data on an external device Data Dump Screen will ask you to conﬁrm the data transmis- sion Parameter Guide Program parameters Global parameters Page01 Common +3, 2+2, 3+1 Page03 Voice VoicePage02 Name GLB Page04 Pitch PitchOscillator Page05 OSC Dwgs Page07 Mixer MixerPage06 OSC OFF Filter Page08 Filter Page09 AMP AMP AmpliﬁerEG Envelope Generator Page10 EG Page11 EG 32...1/1 LFO Low Frequency OscillatorPage12 LFO Page13 LFO Page14 PATCH1 Page15 PATCH2 Page16 PATCH3 Page17 PATCH4 Virtual PatchMOD Sequence Page18 SEQ Common Page21 SEQ3 Page19 SEQ1Page20 SEQ2 Page22 MOD FX Page23 Delay FXEffects Page24 EQ Arpeggiator Page25 Arpeggio Utility Page26 Utility CopySeq SwapTimbreInitSeq Swap Seq CopySeqAllSwapSeq Wave  Saw...Audio Control1  000 127 Control2  AudioPage06 Audio Threshold  000...127 AMP CH Param Init ch Lvl Init ch Pan 001...127 Page1 Global430.0Hz...450.0Hz Const Internal...Auto Page2 Memory Page3 MidiPreload A00...H16 Page4 Midi FilterChg Page5 Ctrl Change Page6 PEDAL&SW Page7 User Scale Page8 Calib Program change About MidiMidi channels Aftertouch Control changes Control changes Bn, cc Gate values Parameters transmitted and received via NrpnControlling the arpeggiator Controlling the Virtual Patch 1-4 Destination Other controlsControlling the Virtual Patch 1-4 Source Controlling the FC MOD source of a vocoder program Filter SEQ2/CH PAN System exclusive messages Transmitting sound settings etc. Data Dump Front panel knob/key control change assignments Wave CC#77 Control 2 values when OSC 1 Wave = Dwgs OSC 2 Semitone values Voice Name List SEQ Arpeggiator D01 Ana Fuzz Synth Hard Single G01 Square Comp Synth Hard Single Blank chart Program No Program Name Timbre2 Dual/Split Vocoder Program Troubleshooting Speciﬁcations and options Symbols Index Latch Delay FX LFO Midi Implementation Chart