Manuals / Lantronix / Computer Equipment / Network Card

Lantronix Ethernet manual Compliance Information

Models: Ethernet

1 92

Download 92 pages 13.42 Kb

Page 88

Compliance

Compliance Information

Manufacturer’s Name & Address:

Lantronix 15353 Barranca Parkway, Irvine, CA 92618 USA

Declares that the following product:

Product Name: WiBox Device Server Model: WBX2100E

Conforms to the following standards or other normative documents:

Safety:

UL 60950-1

CAN/CSA-C22.2 No. 60950-1-03

EN 60950-1:2001, Low Voltage Directive (73/23/EEC)

EMC & Radio:

CFR Title 47 FCC Part 15, Subpart B and C, Class B

Industry Canada ICES-003 Issue 4 (2004), Class B

Industry Canada RSS-Gen Issue 1 (2005)

Industry Canada RSS-210 Issue 6 (2005)

EN 301 489-1 v1.4.1 (2002-08), EMC Directive (1999/5/EC)

EN 301 489-17 v.1.2.1 (2002-08), EMC Directive (1999/5/EC)

EN 300 328 v1.4.1 (2003-04), R&TTE Directive (1999/5/EC)

Australia / New Zealand AS/NZS CISPR 22 (2006), Class B

AS/NZS 4771 (2000 + A1:2003) (radio)

Japan VCCI (EMC emissions) V-3/2006-04

EN55022: 1998 + A1: 2000 + A2: 2003

EN55024: 1998 + A1: 2001 + A2: 2003

EN61000-3-2: 2000 + A2: 2005

EN61000-3-3: 1995 + A1: 2001

Manufacturer’s Contact:

Director of Quality Assurance, Lantronix

15353 Barranca Parkway, Irvine, CA 92618 USA

Tel: 949-453-3990

Fax: 949-453-3995

WiBox2100E User Guide

88

Image 88

Lantronix Ethernet manual Compliance Information

Contents

WiBox2100E User Guide Lantronix Corporate Headquarters Technical Support Sales OfficesContents Setup Mode Server Configuration ContentsSetup Mode Advanced Settings List of Tables ComplianceList of Figures Serial Tunneling Infrastructure Network ExamplePurpose and Audience Using This GuideChapter Summary Using This Guide Additional DocumentationApplications IntroductionName Model Part Numbers Serial Tunneling Network Application ExamplesIntroduction Ad Hoc Network Serial Tunneling InfrastructureConfiguration Methods Protocol SupportAd Hoc WiBox Connection WiBox with EthernetWlan Settings Addresses and Port NumbersHardware Address IP AddressSerial Connector Pinouts DB9M DTE Serial ConnectorRS-485 2-Wire Pinouts WBX2100E Network InterfaceLEDs Ethernet Connector PinoutsWiBox LEDs Technical Specifications Quick Start Required InformationHardware Address 00-20-4a IP Address Subnet Mask GatewayInstalling and Configuring the WiBox WEP Enabled Y/N? WEP Key 64 bit or 128 bit?WPA Enabled Y/N WPA Key Type hex or passphrase? Quick StartSyntax is SetZone IP address zone abbreviation WEP Using Device Installer To install the DeviceInstallerViewing the Current Configuration To view the WiBox’s configuration settingsFirmware Upgradeable Rate Supports Wired EthernetWebPort Maximum Baud RateQuick Start Web-Manager Configuration Accessing Web-Manager through a Web BrowserNetwork Configuration Web-Manager ConfigurationAutomatic IP Address Configuration Select Obtain IP address automaticallyAuto-IP Dhcp Host NameServer Configuration Static IP Address ConfigurationEthernet Configuration Select Use the following IP configurationServer Configuration To configure the WiBox’s device server settingsAdvanced Hostlist Configuration To configure the WiBox’s hostlistCPU Performance Mode Http Server PortChannel 1 and Channel 2 Configuration Serial SettingsRetry Settings Host InformationPort Settings Disable Serial PortChannel ProtocolPack Control Flush Input Buffer Serial to NetworkConnection Settings TCP Flush Output Buffer Network to SerialConnect Protocol At Time of DisconnectConnect Mode Passive Connection Connect Mode Active ConnectionEndpoint Configuration Common OptionsConnection Settings UDP Disconnect ModeDatagram Mode Datagram TypeTo configure the WiBox’s Wlan settings Wlan ConfigurationDevice Address Table Wireless Network Configuration Wireless Network SecurityNetwork Name Network Type Select Infrastructure or Ad Hoc ChannelWEP Options Advanced SettingsWPA Options Updating Settings Applying DefaultsTelnet or Serial Port Setup Mode Configuration Accessing Setup ModeTelnet Connection To establish a Telnet connectionExiting Setup Mode Telnet or Serial Port Setup Mode ConfigurationTo exit Setup Mode Serial Port ConnectionSetup Mode Server Configuration Server Configuration OptionNetwork Mode IP AddressChange Telnet Configuration Password Setup Mode Server ConfigurationSet Gateway IP Address Netmask Number of Bits for Host PartDhcp Name Channel 1 Option Setup Mode Channel ConfigurationBaudrate Interface Mode Setup Mode Channel ConfigurationMode Option Common I/F Mode Setting Binary HexConnect Mode Port NumberFlow Control Option Hex Port Numbers Reserved forConnect Mode Option Connect Mode OptionsIncoming Connection ResponseResponse Incoming ConnectionActive Startup Manual Connection Manual Connection Address ExampleTo enable the hostlist Autostart AutomaticConnection HostlistModem Mode Datagram Type11. Modem Mode Messages Message MeaningFull Verbose Numeric ResponseSend the Escape Sequence +++ in Modem Mode Modem Mode Function CommandModem Mode Commands Auto Increment Source PortDisconnect Mode Option Disconnect Mode OptionsRemote IP Address Remote PortFlush Mode Buffer Flushing Pack ControlDisConnTime Inactivity Timeout Packing IntervalTrailing Characters Send CharactersChannel Port Password Wlan SettingsSend Characters Telnet Terminal TypeAdhoc Network Channel Network Name SsidSecurity Fixed or Automatic Data Rate Transmission Data RateEnable Power Management Expert Settings Option Setup Mode Advanced SettingsTCP Keepalive time in seconds ARP Cache timeout in seconds Disable Monitor Mode at bootupCPU Performance Http Port NumberSecurity Settings Disable Port 77FE Hex Disable Web ServerDisable Web Setup Disable Echo PortsGenerally, one of two situations applies Channel 1 Configuration Default SettingsChannel 2 Configuration Expert Settings Security SettingsEnable Power Management Channel SecurityExit Configuration Mode Monitor Mode Entering Monitor Mode via the Serial PortEntering Monitor Mode via the Network Port Monitor Mode CommandsMonitor Mode Command Response CodesResponse Meaning G0, G1, ....,Ge, GfUsing Tftp Graphical User Interface Updating FirmwareObtaining Firmware Reloading Firmware ROM FileNetwork Upgrade Using Tftp Command Line InterfaceUpdating Firmware To download new firmware from a computerWlan Country Setting Syntax is SetZone IP address zone abbreviationConfiguring the WiBox in Bridging Mode Wireless BridgingMethod Troubleshooting Troubleshooting Diagnostic LED StatesProblems and Error Messages Problem/Message Reason SolutionLater, there is only one setting for WiBox2100E only Caps Lock is not onTechnical Support Technical Support Europe, Middle East, and AfricaBinary to Hexadecimal Conversions Converting Binary to HexadecimalConversion Table Scientific CalculatorBinary to Hexadecimal Conversions Compliance Compliance InformationRegulatory Information USA Federal Communications Commission FCC NoticeCanada Industry Canada Notice ComplianceEurope R&TTE Directive 99/5/EC, Wireless Notice Australia & New Zealand Wireless NoticeAntenna Notice Exposure of Humans to RF FieldsCompliance Warranty