Log Messages

B

 

 

 

This appendix contains brief explanations of log messages that are generated by the SP Switch Router Adapter card. You will see most of them in the /var/log/gr.console file.

Alphabetical list of messages

The first line of each error message and the page on which it appears are listed here:

“Access FIFO Sync Error from RC, int1=%d”. . . . . . . . . . . . . . . . . . . . . . . B-3 “Access FIFO Sync Error from TC, int1=%d” . . . . . . . . . . . . . . . . . . . . . . . B-3 "ACK WORDS: 0x%08x, 0x%08x, 0x%08x, 0x%08x, ” . . . . . . . . . . . . . . B-3 “ARP added: IP= %s, SW-node=%d, state=%d” . . . . . . . . . . . . . . . . . . . . . B-4 “Bad Hdr/Svc received, Ret code=%d” . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4 “Board Configuration timed-out, retrying” . . . . . . . . . . . . . . . . . . . . . . . . . B-4 “Broadcasting an ARP Request.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4 “Broadcasting a Gratuitous ARP Request” . . . . . . . . . . . . . . . . . . . . . . . . . B-4 “Configuration Parameters:”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5 “Configuring transmit side.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5 “CPU ready msg received from TX-CPU”. . . . . . . . . . . . . . . . . . . . . . . . . . B-5 “Descriptor Sync Error from RC, int1=%d” . . . . . . . . . . . . . . . . . . . . . . . . B-6 “Descriptor Sync Error from TC, int1=%d”. . . . . . . . . . . . . . . . . . . . . . . . . B-6 “Discarding msg, unknown msg_type 0x%x” . . . . . . . . . . . . . . . . . . . . . . . B-6 “ERR! Duplicated buffer %d” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6 “Expect NODE_INIT but received Stat/Err Request” . . . . . . . . . . . . . . . . . B-7 “Expired IP buffer received: %d” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7 “Hot interrupt detected, ier1=0x%8x, ier2=0x8x” . . . . . . . . . . . . . . . . . . . . B-7 “Hot interrupt detected, ier1=0x%8x, ier2=0x8x” . . . . . . . . . . . . . . . . . . . . B-7 “Initializing Main Task...” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7 “Initializing RX Subsystem data structure.”. . . . . . . . . . . . . . . . . . . . . . . . . B-8 “IOSTB3:RX SET TOD service message received.” . . . . . . . . . . . . . . . . . . B-8 “Loopback routes found for IP adr: 0x%x, sw-node.” . . . . . . . . . . . . . . . . . B-8 “Lost of STI clock, TBIC Status = 0x%x.” . . . . . . . . . . . . . . . . . . . . . . . . . B-8 “Lost of STI clock, TBIC Status = 0x%x.” . . . . . . . . . . . . . . . . . . . . . . . . . B-8 “NetStar GigaRouter %s RX Interface Initializing:” . . . . . . . . . . . . . . . . . . B-9 “NetStar GigaRouter %s TX Interface Initializing:” . . . . . . . . . . . . . . . . . . B-9 “RX: Clock is valid.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9 “RX-CPU Loaded msg received from TX-CPU.” . . . . . . . . . . . . . . . . . . . . B-9 “RX: got TBIC INITED from TX.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10 “RX: Port connected, stat=0x%x.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10

SP Switch Router Adapter Guide - 1.4 Update 2

October 22, 1999 B-1

Page 115
Image 115
Lucent Technologies 9077 04S, 9077 16S, 9076 manual Log Messages, Alphabetical list of messages