SDP-ECO 1630 III Printer Manual: Safety and Heat Element Information

SDP-Eco1630 III USERS MANUAL

Chapter 1 On Safety

1.6Precautions during transport and installation

•The weight of the SDP-Eco 1630 III is described in "Chapter 9: Specifications"Make sure the floor is fully capable of handling 2500 N/m2 (approx. 55 lbs/ft2) or heavier loading before installing the SDP-Eco 1630 III .

•Transport and installation

This machine's transport and installation must always be handled by engineers and contractors assigned by Mitsubishi Paper Mills Limited. We shall bear no responsibility whatever for any unit breakage, damage, or malfunctions caused by or during transport or installation performed by anyone other than the above specified personnel. Whenever your machine must moved, transferred, or reinstalled, please entrust all procedures to our nearest branch office or dealer.

1.7 SDP-Eco 1630 III Installation

•Installation environment

Installing the machine in the following locations may cause machine damage or malfunctions. Do not install the machine anywhere that is exposed or subject to:

*Locations with strong and/or persistent vibration

*Locations with an uneven floor

- 10 -

Image 18

Mitsubishi Electronics SDP-ECO 1630 III manual Precautions during transport and installation, SDP-Eco 1630 III Installation

Contents

Page III For Your Safety Compliance with FCC Rules When export the machineCompliance with Cispr Rules Limit of responsibility Introductory Note About this manual Contents Menus and panel displays Power supply On SafetyWhen using the machine Maintenance and safe passage during emergencies SDP-Eco 1630 III is equipped with a leakage circuit breaker This machine incorporates a power supply unitSafety switches This machine incorporates high current electrical circuits For European model Types of warning labels Hazard Safe handling method Locations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Before connecting the power cable Power cables Operation precautions Unacceptable Transport and installation Precautions during transport and installationSDP-Eco 1630 III Installation Installation environment Ventilation Maintenance Installation space Machine disposal Page Names of Machine Components and Parts Main unitPage Operation panel Safety switch Plate setting Handling plates Two set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Operation Cable connection check Turning on the power switch InitializationPanel display flow after machine startup Press the Menu Key to display Amount using the key or Key and register the value with Exposure Remote exposureLocal exposure Exposure Processor section Preparing and pouring processing chemicalProcessing chemical replenishment Processing chemical replacement Preparing rinse water Handling waste liquid If the machine is not used for a long period Turning OFF the power supply and inspection at shutdown Collecting exposed plates Operation Page Menus and panel displays User menu Operation status Menu/command selection Power ON/OFF keyRemote mode display Panel operation Switch the mode between remote and local Shift between commands ExampleCommand execution Data channel User menuPlate data Plate type Laser menu Resolution settingLaser setting Remaining amount of plate Laser test exposure Pre. Feed menu Mode menuPunch specifications Image Data menu Maintenance menu Rinse Procedure In cases where the current values are changed to Key Maintenance Cutter blade replacementReplacement procedure Cylindrical lens cleaning Dust, clean it off with a blower Filter cleaning Punch dust removal Cleaning the processor section Resetting the punch counterCleaning the processor rack Processor rack Stay Cleaning the processing chemical tank and filter Re-attach the supply guides to the processor rack Cleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion How to order parts List of expendable parts Month Year SDP-Eco 1630 III Maintenance and Inspection Chart Displaying and clearing errors MessageMessage Status display Message Operation status List of error messages Message Error contents ME9 Jam removal procedure Removing Plate jam 1 Removing Plate jam Specifications Basic specifications Overview diagram Silver Digiplater