Specifications | Mitsubishi Electronics SDP-ECO 1630 III instruction

Chapter 9 Specifications

Chapter 9 Specifications

9.1 Basic specifications

- Recording system	...	Flatbed scanning system
- Light source	...	635 nm laser diode
- Resolution	...	1200 dpi, 1500 dpi, 1800 dpi, 2400 dpi
- Exposure speed	...	1236 mm/min (1200 dpi)
		791 mm/min (1500 dpi)
		549 mm/min (1800 dpi)
		309 mm/min (2400 dpi)
- Plates	...	SDP-FR100 (Winding length: 75 meters)
		SDP-FRm175 (Winding length: 61 meters)
		SDP-RR175 (Winding length: 75 meters)
- Plate width [cm (inches)]	...	22.9 (9), 25.4 (10), 27.9 (11), 30.5 (12),
		31.0 (12 1/5),32.4 (12 3/4), 33.5 (13 3/16),
		34.0 (13 3/8),37.0 (14 9/16), 40.0 (15 3/4),
		40.4 (15 7/8),41.4 (16 3/10)
- Effective exposure width	...	404 mm
- Maximum exposure width ...		424 mm
- Plate cut length	...	220 to 580 mm
- Cutter	...	Slide cutter
- Plate joint detector	...	Panel display, automatic over cut
- Dehumidifier	...	Panel heater
- Activation method	...	Coating (Ecology adapted model)
- Tank capacity	...	SLM-EAC 0.55 liters, SLM-EST 0.6 liters
- Processing chemicals	...	SLM-EAC, SLM-EST (2 liters per bottle)
- Rinse water tank	...	0.26 liters
- Rinse water	...	Rinse water replenisher bottle 1.0 liters
- Processor speed	...	15 mm/sec.
- Original speed	...	114 sec. (1200 dpi	450 mm long)
	...	189 sec. (2400 dpi	450 mm long)
- Cycle time	...	44 sec. (1200 dpi	450 mm long)
	...	124 sec. (2400 dpi	450 mm long)
- Solution temperature control ...		140W (AC 115V) panel heater 30 to 34 ˚C
- Plate preheater	...	140W (AC 115V) heat roller
- Dryer	...	600W (AC 115V) fin heater
		Thermo controller switch system (H or L)
- Interface	...	FAST WIDE SCSI (16 bit)
- Power supply capacitance ...		Single phase 100 to 120V, 10A, 1.2 kW, 50/60 Hz
		Single phase 200V 6A/ 220V 5.5A/ 230V 5.5A
		240V 5A/ 1.2 kW 50/60 Hz
- Machine size (mm)	...	W 1000 x D 795 x H 1070
- Weigh	...	100 to 120V type: 185 kg
		200/220/230/240V type: 207 kg
- Installation environment	...	Temperature 18 to 28˚C, Humidity 50 to 70%
- Noise	...	60 dB (A) or lower
- Option	...	Memory module for extension
		Differential unit (Cable 20 meters)
		DS punch unit (Alternately positionable)
		BELL punch unit

- 73 -

Image 81

Mitsubishi Electronics SDP-ECO 1630 III manual Specifications, Basic specifications

Contents

Page III For Your Safety Compliance with Cispr Rules When export the machineCompliance with FCC Rules Limit of responsibility Introductory Note About this manual Contents Menus and panel displays When using the machine On SafetyPower supply Maintenance and safe passage during emergencies Safety switches This machine incorporates a power supply unitSDP-Eco 1630 III is equipped with a leakage circuit breaker This machine incorporates high current electrical circuits For European model Hazard Safe handling method Types of warning labels Locations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Power cables Before connecting the power cable Unacceptable Operation precautions SDP-Eco 1630 III Installation Precautions during transport and installationTransport and installation Installation environment Ventilation Installation space Maintenance Machine disposal Page Main unit Names of Machine Components and PartsPage Operation panel Safety switch Handling plates Plate setting Two set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Cable connection check Operation Turning on the power switch InitializationPanel display flow after machine startup Press the Menu Key to display Amount using the key or Key and register the value with Exposure Remote exposureLocal exposure Exposure Processor section Preparing and pouring processing chemicalProcessing chemical replenishment Preparing rinse water Processing chemical replacement If the machine is not used for a long period Handling waste liquid Collecting exposed plates Turning OFF the power supply and inspection at shutdown Operation Page User menu Menus and panel displays Operation status Remote mode display Power ON/OFF keyMenu/command selection Panel operation Switch the mode between remote and local Shift between commands ExampleCommand execution Plate data User menuData channel Plate type Laser setting Resolution settingLaser menu Remaining amount of plate Laser test exposure Punch specifications Mode menuPre. Feed menu Image Data menu Rinse Maintenance menu Key Procedure In cases where the current values are changed to Maintenance Cutter blade replacementReplacement procedure Dust, clean it off with a blower Cylindrical lens cleaning Filter cleaning Punch dust removal Cleaning the processor section Resetting the punch counterCleaning the processor rack Processor rack Stay Re-attach the supply guides to the processor rack Cleaning the processing chemical tank and filter Cleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion List of expendable parts How to order parts Month Year SDP-Eco 1630 III Maintenance and Inspection Chart Displaying and clearing errors MessageMessage Message Operation status Status display Message Error contents List of error messages ME9 Removing Plate jam 1 Jam removal procedure Removing Plate jam Basic specifications Specifications Overview diagram Silver Digiplater