Manuals / NCR / Computer Equipment / Server

NCR S16 manual

Models: S16

1 108

Download 108 pages 54.46 Kb

<>

Install Configuring PCI Adapters Documentation Needed for Setup Confirming the Cmos Settings How to Power Management Mode Rebooting the System Enable 4 GB Support Using an Adaptec Controller

Page 36

Performing a Full Installation of Windows NT Server 3.51

4-12	Installing Microsoft Windows NT Server 3.51

Page 35 Page 37

Image 36

NCR S16 manual

Page 35 Page 37

Related pages Troubleshooting for Hotpoint AQCF 852 BU Specification S for JVC AV 27D200 LCD error messages for Muratec F-360 Stereo Pair Bus Out Block Diagram for Yamaha 01v  When or is displayed, skip step for Panasonic CF-53ASUZX1M DSView 3 Software Installer/User Guide for Avocent SPC420 Parts List for Panasonic FV-08VQCL6 Appendix B Country code list for parental lock for JVC XV-D721BK Pausing the picture for Toshiba TDP-MT700 What certifications does the Bosch D9412GV4 have?

Contents

NCR S16 Minitower Server Page Contents Installing Windows NT Server 4.0 Enterprise Edition Installing SCO Unix ViContents Preface About This BookWho Should Read This Book Conventions Used in This Book Related Publications Installation Overview Overview Documentation Needed for Setup Where to Start Step What to Do How to Do It Where to Find Information Confirming the Cmos Settings and Configuring PCI Adapters Confirming the Cmos Settings and Configuring PCI Adapters Confirming the Cmos Settings Return to Page 1, and set parameters as follows ECC Power Management Mode Configuring PCI Adapters Inta Intb Intc Intd Configuring PCI Adapters Configuring PCI Adapters Confirming the Scsi Adapter Settings Confirming the Scsi Adapter Settings Configuring the Scsi Adapters For Wide devices only Configuring the Scsi Adapters Send Start Unit Command Installing Microsoft Windows NT Server Installing Microsoft Windows NT Server Performing a Full Installation of Windows NT Server Entering Windows Setup Inserting the Windows NT Server Setup Disk Installing from the CD-ROMPreparing the Hard Disk Performing a Full Installation of Windows NT Server Performing a Full Installation of Windows NT Server Completing User and Server Information Continue Selecting Network Protocols Providing Additional Setup Information Completing the Installation Performing a Full Installation of Windows NT Server Page Installing Microsoft Windows NT Server Overview Pre-Loaded Installation Starting the Pre-Loaded InstallationEntering the Setup Routine for NCR Server Manager Completing the Pre-loaded Installation Pre-Loaded Installation Non-Pre-Load Installation Performing a Full Installation of Windows NT Server Preparing the Hard Disk Performing a Full Installation of Windows NT Server Installing the Network Selecting Network Protocols Entering Additional Setup Information Installing Windows NT Server 4.0 Enterprise Edition Action Reference Install Service Pack Enable 4 GB Support Boot.ini File Before Modification Example Boot.ini File After Modification Example Enable 4 GB Support Installing Netware Installing Netware Installation Overview Rebooting the Server and Creating a Primary DOS Partition Rebooting the Server and Creating a Primary DOS Partition Using an Adaptec Controller Loading the Controller’s Drivers Loading the CD-ROM as a NetWare Volume Installing NetWare Switching to the System Console Screen Choosing Drivers Completing the Installation Load Smcpwr SLOT=? FRAME=???? NAME=SMCPWR1E83 Installing NetWare Installing SCO Unix Installing SCO Unix Installation Overview Rebooting the Server and Installing the Operating System Entering Setup Information Inserting the Supplement Volume Disk Inserting the CD-ROM Rebooting the System SCO Release 3 Installing TCP/IP Communications Inserting the Latest SMC Driver Disk Completing the Installation SCO Release 5 Installing TCP/IP Communications Inserting the SMC SuperDisk Select Add Protocol. Observe the following Installing UnixWare Installing UnixWare Installation Overview Inserting the Host Bus Adapter HBA Driver Selecting the Installation Method Observing Screen Messages Reinserting the Host Bus Adapter HBA Driver Disk Entering a Password and Completing the Installation Rebooting the Server and Installing the Operating System Installing OS/2 10-2 Installation Overview 10-4 Editing CONFIG.SYS and Rebooting Installing OS/2 Installing MP-RAS Installing MP-RAS Installation Overview Default Installation Overview Restarting the Installation Performing a Default Installation Booting from the Installation Media Selecting the Type of Installation Selecting the Install Media Device Entering the System Name, Date, and Time Specifying the Secondary Disk Installing Licenses Install Licenses Methods Licenses, press a 11-12 Turning the System Off Performing Additional Administrative Tasks Configuration Settings Required for Installing MP-RAS Shadow Options Embedded Adaptec AIC-7880 Scsi Controller Used Resources 11-18

Top Page Image Contents