Manuals / NCR / Computer Equipment / Server

NCR S16 manual Installing OS/2

Models: S16

1 108

Download 108 pages 54.46 Kb

Install Configuring PCI Adapters Documentation Needed for Setup Confirming the Cmos Settings How to Power Management Mode Rebooting the System Enable 4 GB Support Using an Adaptec Controller

Page 85

Chapter 10

Installing OS/2

NCR S16 Minitower Server Installing Network Operating System

10-1

Page 84 Page 86

Image 85

NCR S16 manual Installing OS/2

Page 84 Page 86

Related pages All Install page Installation dimensions for Miele CS 1028 Installation for Dayton 3VG81 Installation for GSI Outdoors PNEG-377 Filter Installation for Sharp FP-R30CX

Contents

NCR S16 Minitower Server Page Contents Installing Windows NT Server 4.0 Enterprise Edition Installing SCO Unix ViContents About This Book PrefaceWho Should Read This Book Related Publications Conventions Used in This Book Installation Overview Overview Documentation Needed for Setup Step What to Do How to Do It Where to Find Information Where to Start Confirming the Cmos Settings and Configuring PCI Adapters Confirming the Cmos Settings and Configuring PCI Adapters Return to Page 1, and set parameters as follows Confirming the Cmos Settings ECC Power Management Mode Inta Intb Intc Intd Configuring PCI Adapters Configuring PCI Adapters Configuring PCI Adapters Confirming the Scsi Adapter Settings Confirming the Scsi Adapter Settings For Wide devices only Configuring the Scsi Adapters Configuring the Scsi Adapters Send Start Unit Command Installing Microsoft Windows NT Server Installing Microsoft Windows NT Server Entering Windows Setup Performing a Full Installation of Windows NT Server Installing from the CD-ROM Inserting the Windows NT Server Setup DiskPreparing the Hard Disk Performing a Full Installation of Windows NT Server Performing a Full Installation of Windows NT Server Continue Completing User and Server Information Selecting Network Protocols Providing Additional Setup Information Completing the Installation Performing a Full Installation of Windows NT Server Page Installing Microsoft Windows NT Server Overview Starting the Pre-Loaded Installation Pre-Loaded InstallationEntering the Setup Routine for NCR Server Manager Completing the Pre-loaded Installation Pre-Loaded Installation Non-Pre-Load Installation Performing a Full Installation of Windows NT Server Preparing the Hard Disk Performing a Full Installation of Windows NT Server Installing the Network Selecting Network Protocols Entering Additional Setup Information Installing Windows NT Server 4.0 Enterprise Edition Action Reference Install Service Pack Boot.ini File Before Modification Example Enable 4 GB Support Boot.ini File After Modification Example Enable 4 GB Support Installing Netware Installing Netware Installation Overview Rebooting the Server and Creating a Primary DOS Partition Rebooting the Server and Creating a Primary DOS Partition Loading the Controller’s Drivers Using an Adaptec Controller Loading the CD-ROM as a NetWare Volume Installing NetWare Choosing Drivers Switching to the System Console Screen Completing the Installation Load Smcpwr SLOT=? FRAME=???? NAME=SMCPWR1E83 Installing NetWare Installing SCO Unix Installing SCO Unix Installation Overview Entering Setup Information Rebooting the Server and Installing the Operating System Inserting the CD-ROM Inserting the Supplement Volume Disk Rebooting the System Inserting the Latest SMC Driver Disk SCO Release 3 Installing TCP/IP Communications Completing the Installation Inserting the SMC SuperDisk SCO Release 5 Installing TCP/IP Communications Select Add Protocol. Observe the following Installing UnixWare Installing UnixWare Installation Overview Inserting the Host Bus Adapter HBA Driver Observing Screen Messages Selecting the Installation Method Reinserting the Host Bus Adapter HBA Driver Disk Entering a Password and Completing the Installation Rebooting the Server and Installing the Operating System Installing OS/2 10-2 Installation Overview 10-4 Editing CONFIG.SYS and Rebooting Installing OS/2 Installing MP-RAS Installing MP-RAS Installation Overview Default Installation Overview Restarting the Installation Booting from the Installation Media Performing a Default Installation Selecting the Type of Installation Entering the System Name, Date, and Time Selecting the Install Media Device Specifying the Secondary Disk Install Licenses Methods Installing Licenses Licenses, press a 11-12 Turning the System Off Performing Additional Administrative Tasks Shadow Options Configuration Settings Required for Installing MP-RAS Embedded Adaptec AIC-7880 Scsi Controller Used Resources 11-18

Top Page Image Contents