Nuance comm D60709-22 3.1.3 Connect hardware

3 SafeCom Controller

D60709-22

3.1.3 Connect hardware

Make sure that the SafeCom software installation has been completed before

you connect the hardware. When powered up, the hardware automatically

discovers the server software.

Figure 1 SafeCom Controller’s rear panel

1. Switch off the power to the device.

2. Connect a network cable to the LAN port on the rear panel of the

SafeCom Controller. Connect the other end of the cable to the network.

3. Connect a network cable to the device. Connect the other end of the

cable to the SafeCom Controller’s other network port.

4. Connect the SafeCom Controller and the optional SafeCom Card Reader.

5. Connect the power supply to the SafeCom Controller. When you power

on, you must wait approx. 1 minute while SafeCom initializes.

6. Switch on the power to the device.

USB host

LAN

network port

power

serial port test button

USB

device

Contents

Main Page Table of Contents Page 1 Introduction 1.1 SafeCom Go Sharp 1.2 Requirements Page 1.3 SafeCom ID Devices 1.4 Sharp device passwords 1.5 Available documentation 1.6 About this manual 1.7 Document history Page 2 SafeCom Go Sharp - Device server 2.1 Overview 2.2 SafeCom Go Sharp - Device server installation 2.2.1 Installation 2.2.2 Windows Firewall - Ports that must be opened Page 2.3 Configure SafeCom Device Server 2.3.1 Login to SafeCom Device Server 2.3.2 Add SafeCom Server 2.3.3 Device Server config.ini 2.4 Add device to a SafeCom Device Server 2.4.1 Device icons 2.4.2 Add device via SafeCom Device Server 2.4.3 Add device via SafeCom Administrator Page Page 2.5 Configure device in SafeCom Device Server Page Page Page 2.6 SafeCom Go Sharp - How to 2.6.1 Get the SafeCom Go Sharp software 2.6.2 Select login method 2.6.3 Enable Copy 2.6.4 Enable E-mail 2.6.5 Control user access rights 2.6.6 Register device 2.6.7 Enable SafeCom Mobile Pull Print 2.6.8 Restore factory default 2.6.9 At the printer: SafeCom error message when coming out of power save 2.6.10 Uninstall SafeCom Go Sharp 3 SafeCom Controller 3.1.1 Installation with SafeCom Controller 3.1.2 Write down the IP address of the device 3.1.3 Connect hardware 3.1.4 Add device in SafeCom Administrator Page 3.2 Configure the Sharp device web interface 3.2.1 New Sharp devices Page Page Page Page 3.2.2 Sharp Web Interface (old models) Page Page 3.3 Configure the SafeCom Controller Web Interface 3.3.1 Login to the SafeCom Controller Web Interface 3.3.2 Advanced Configuration web page 3.3.3 SafeCom web page 3.3.4 Printer web page 3.4 SafeCom Go for Controller - How to 3.4.1 Enable copy tracking for Controller 3.4.2 Specify SafeCom Server and device connection 3.4.3 Register device 3.4.4 Set password to prevent unauthorized access 3.4.5 Assign a fixed IP address to the SafeCom Controller 3.4.6 Select user identification 3.4.7 Disable the Test button 3.4.8 Enable Copy Control 3.4.9 Enable High Speed Print 3.4.10 Access Sharp MFPs System Settings 3.4.11 Restore factory default 3.4.12 Resend configuration 3.4.13 Uninstall SafeCom Go Sharp 4 Using SafeCom Go Sharp 4.1 Sharp device with SafeCom Device Server 4.1.1 Login Page 4.1.3 Pull Print - Document list 4.1.4 Copy 4.1.5 Account Select billing code 4.1.6 Register card with PUK code 4.1.7 Logout 4.2 Sharp device with SafeCom Controller 4.2.1 Control panel 4.2.2 Login 4.2.3 Main menu 4.2.4 Pull Print - Document list 4.2.5 Copy 4.2.6 Logout 4.2.7 Register card with PUK code 5 Troubleshooting 5.1 SafeCom Help Desk Assistant 5.2 Servlets 5.3 SafeCom Administrator: Unable to locate all SafeCom devices 5.4 Copy jobs are not tracked 5.5 Print performance is slow 5.6 At the printer: No billing codes available 5.7 MFP reports: Could not access the accounting server 5.8 ERROR[5000]: Processing is in motion 5.9 Device Server: Configuration of devices failed 5.10 Device Server: Error when upgrading existing device server installation 5.11 SafeCom reader does not work 6 Regulatory information 7 Index