Parts and their functions

1

1

2

3

4

 

 

 

 

 

 

 

 

 

 

 

 

 

LEVEL ·

BACKLIGHT

 

 

 

 

 

 

 

 

 

 

 

 

BACKLIGHT

LIGHT

 

 

 

 

 

 

 

 

 

 

 

 

LIGHT

DARK

 

 

 

 

 

 

 

 

 

 

 

 

DARK

OFF

 

 

 

 

 

 

 

 

 

 

 

 

OFF

BRIGHTNESS

 

 

 

 

 

 

 

 

 

 

 

 

BRIGHTNESS

COUNTER/

 

 

 

 

 

 

 

 

 

 

 

 

COUNTER/

REMAIN

 

 

 

 

 

 

 

 

 

 

 

 

REMAIN

CH CONDITION

 

 

 

 

EVENT

 

 

 

CH CONDITION

 

METER

 

 

 

 

 

 

 

 

 

 

 

 

METER

FULL/

 

 

 

 

 

 

 

 

 

 

 

 

FULL/

FINE

 

 

 

 

 

 

 

 

 

 

 

 

FINE

RESET

 

 

 

 

 

 

 

 

 

 

 

 

RESET

CTL

 

 

 

 

V1

V2

 

 

 

 

 

 

CTL

TC

 

 

 

 

 

 

 

 

 

 

TC

 

 

 

 

 

 

 

 

 

 

 

 

UB

 

 

 

VTR 1

 

 

VTR 2

 

 

ANALOG

 

OPERATION

UB

 

 

 

 

 

 

 

 

EDIT MODE

V2

CONTROL

PREROLL SYNCHRO

MODE

TC

REC INHIBIT

MODE

TC

REC INHIBIT

 

IN AUDIO OUT

VIDEO IN

REMOTE

7

CF

TAPE

REGEN

ON

TAPE

REGEN

ON

2 CH

V1-V2

2 CH

INT

SDI

LOCAL

5

ON

 

R-RUN

 

 

R-RUN

 

4 CH

V1

4 CH

EXT

 

EXT VTR

3

OFF

EE

F-RUN

OFF

EE

F-RUN

OFF

 

 

V2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SEPARATE

ANALOG

EJECT

M-cassette

M-cassette

EJECT

 

Caution Do not Insert S-cassette or with adaptor

Caution Do not Insert S-cassette or with adaptor

<

 

 

<

 

 

 

 

VTR 1

 

VTR 2

2

3

4

Panel control area

1Audio monitor speakers

The sound of the VTR1 (or VTR2) signals to be monitored is delivered through the VTR1 (or VTR2) speaker.

Depending on the positions selected for the AUDIO MONITOR SELECT switches, VTR1 or VTR2 sound is selected and output.

2LCD switch

This functions as the LCD monitor power switch, and it also selects the brightness of the display’s backlight.

LIGHT: For increasing the display’s backlight brightness.

DARK: For reducing the display’s backlight brightness.

OFF: The LCD monitor is turned off.

3BRIGHTNESS control

Used to adjust the brightness of the LCD monitor.

4COUNTER/REMAIN switch

This is used to switch what is to be shown on the display tube and the superimposed display position on the monitor screen.

Each time the switch is pressed, the display is changed in the sequence presented below.

TCR00:00:04:14

SHTL+0.0

Counter/operation mode display (top position)

TCR00:00:04:14

Counter display

 

 

 

No on-screen display

TCR00:00:04:14

Counter display

 

 

 

Counter/operation mode

 

 

 

display (bottom position)

TCR00:00:04:14

 

SHTL+0.0

 

 

11.8v

r 82

DC voltage/remaining tape

display

 

 

 

(“11.8V/82 minutes” is

 

 

 

 

 

 

indicated in the figure.)

 

 

 

Counter/operation mode

TCR00:00:04:14

display (bottom position)

 

SHTL+0.0

 

 

TCR00:00:04:14

Counter display

7