Panasonic PT-DW100U operating instructions RGB2 input

	Model No.		PT-DW100U
			1 set of high-density, D-sub 15p (female)
			[For YPBPR input]
			Y: 1.0 V [p-p] synchronization signal included, PBPR: 0.7 V [p-p] 75 Ω
		RGB2 input	[For RGB input]
		terminal	0.7 V [p-p] 75 Ω For G-SYNC: 1.0 V [p-p] 75 Ω
			HD/SYNC: TTL, high-impedance, positive/negative polarity automatically adjusted
			VD: TTL, high-impedance, positive/negative polarity automatically adjusted
			• HD/SYNC, and VD terminals are not compliant with 3-value direct SYNC.
		Video input/		1 set BNC
		output terminal	1.0 V [p-p] 75 Ω (Active through for Video output)
		S-video input	1 set Mini DIN 4p
		terminal	Y 1.0 V [p-p] C 0.286 V [p-p] 75 Ω Compliant with S1 signals
Interface		DVI-D input		1 set
			DVI 1.0 compliant
ports		terminal
			HDCP (Single link only) compatible
			1 set (Used for network connection)
		LAN terminal	10BASE-T/100BASE-TX
			PJLink™ compatible
		Serial input	2 sets D-sub 9-pin (female), RS-232C/RS-422 compliant
		terminal	Used for personal computer control
		Serial output	1 set D-sub 9-pin (male), RS-422 compliant
		terminal	Used for personal computer control
		Remote1 input/	1 set each for M3 pin jack
		output terminal	Wired remote control, used for link control
		Remote2 terminal	D-sub 9p (female)
			Used for external control
Length of power supply cord				3.0 m (9.1´)
Cabinet				Molded resin
Outside dimensions			Width: 578 mm (22.8˝), Height : 320 mm (12.6˝), Depth: 643 mm (25.3˝)
Weight			approx. 35 kg (77.1 lb) (without optional projection lens)*2
Working environment			Ambient temperature*3 : 0 °C to 45 °C
condition			Ambient humidity: 10 % to 80 % (no condensation)
		Power source	3 V DC (two AA dry cells)
Remote		Operation range	approx. 30 m (98´5˝) (in front of beam receiver)
control		Mass	134 g (0.31 lb) (including dry cells)
		Outside dimensions	Width: 51 mm (2˝), Thickness: 23 mm (0.9˝), Depth: 176 mm (6.9˝)
			Hanging attachment (For high ceiling):	ET-PKD100H
			Hanging attachment (For low ceiling):	ET-PKD100S
			Projection lens:	ET-D75LE1, ET-D75LE2, ET-D75LE3,
				ET-D75LE4, ET-D75LE5, ET-D75LE6,
				ET-D75LE8
Optional			DVI-D input module:	ET-MD77DV
			SD-SDI input module:	ET-MD77SD1
			HD/SD-SDI input module:	ET-MD77SD3
			Dual link HD/SD-SDI input module:	ET-MD100SD4
			Replacement Lamp Unit:	ET-LAD12K (single bulb),
				ET-LAD12KF (4 bulbs)

*1 70˝ – 300˝ for ET-D75LE5

*2 This is the average value. It may differ depending on each product.

*3 When the projector is used in high altitude mode (1 400 to 2 700 m), the ambient temperature is 0 °C to 40 °C. Furthermore, if the ambient temperature becomes 40 °C or more (35 °C in high altitude mode) when using the projector with lamp 4 lit, light output may be reduced by approximately 30% to protect the projector.

When a smoke cut filter is used, the ambient temperature is 0 °C to 35 °C. However, use at high altitudes is not possible.

Information

ENGLISH – 119